Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Polarization corrosion rates

Linear polarization Corrosion rate General/specialist 1 reading in 5-30 min depending on equipement used... [Pg.49]

Corrosion protection of metals can take many fonns, one of which is passivation. As mentioned above, passivation is the fonnation of a thin protective film (most commonly oxide or hydrated oxide) on a metallic surface. Certain metals that are prone to passivation will fonn a thin oxide film that displaces the electrode potential of the metal by +0.5-2.0 V. The film severely hinders the difflision rate of metal ions from the electrode to tire solid-gas or solid-liquid interface, thus providing corrosion resistance. This decreased corrosion rate is best illustrated by anodic polarization curves, which are constructed by measuring the net current from an electrode into solution (the corrosion current) under an applied voltage. For passivable metals, the current will increase steadily with increasing voltage in the so-called active region until the passivating film fonns, at which point the current will rapidly decrease. This behaviour is characteristic of metals that are susceptible to passivation. [Pg.923]

Other techniques to detennine the corrosion rate use instead of DC biasing, an AC approach (electrochemical impedance spectroscopy). From the impedance spectra, the polarization resistance (R ) of the system can be detennined. The polarization resistance is indirectly proportional to j. An advantage of an AC method is given by the fact that a small AC amplitude applied to a sample at the corrosion potential essentially does not remove the system from equilibrium. [Pg.2720]

Linear polarization re.slstance probe.s. LPR probes are more recent in origin, and are steadily gaining in use. These probes work on a principle outlined in an ASTM guide on making polarization resistance measurements, providing instantaneous corrosion rate measurements (G59, Standard Practice for Conducting Potentiodynamic Polarization Resistance Measurements ). [Pg.2439]

When these conditions are met, the current density associated with a small polarization of the metal (less than +10 mV) is directly proportional to the corrosion rate of the metal. [Pg.2439]

Polarization probes rely on the relationship of the applied potential to the output current per unit area (current density). The slope of applied potential versus current density extrapolated through the origin, yields the polarization resistance Rp, which can be related to the corrosion rate. [Pg.2440]

Information on the process reaction conditions may be impoi tant to prolonging the lifetime of process equipment. Techniques such as EIS and potentiodynamic polarization can provide just such information without being tied to a specific corrosion-rate measurement. [Pg.2440]

Measurements of polarization resistance Rp, given by LPR probes, can lead to measurement of the corrosion rate at a specific instant, since values of Rp are instantaneous. [Pg.2441]

Equation (2-38) is valid for every region of the surface. In this case only weight loss corrosion is possible and not localized corrosion. Figure 2-5 shows total and partial current densities of a mixed electrode. In free corrosion 7 = 0. The free corrosion potential lies between the equilibrium potentials of the partial reactions and U Q, and corresponds in this case to the rest potential. Deviations from the rest potential are called polarization voltage or polarization. At the rest potential = ly l, which is the corrosion rate in free corrosion. With anodic polarization resulting from positive total current densities, the potential becomes more positive and the corrosion rate greater. This effect is known as anodic enhancement of corrosion. For a quantitative view, it is unfortunately often overlooked that neither the corrosion rate nor its increase corresponds to anodic total current density unless the cathodic partial current is negligibly small. Quantitative forecasts are possible only if the Jq U) curve is known. [Pg.44]

When cathodic polarization is a result of negative total current densities 7., the potential becomes more negative and the corrosion rate lower. Finally, at the equilibrium potential it becomes zero. In neutral water equilibrium potentials are undefined or not attainable. Instead, protective potentials are quoted at which the corrosion rate is negligibly low. This is the case when = 1 flA cm (w = lOjUm a ) which is described by the following criteria for cathodic protection ... [Pg.45]

Here U/ is measured after switching off of the protection current and after step polarization. The potential difference corresponds to an IR-fiee potential decay. From the slope in Fig. 2-9, a reduction in the corrosion rate of 100 to 4 /im a" results. [Pg.104]

Oxygen dissolved in aqueous solutions, even in very low concentrations, is a leading cause of corrosion problems (i.e., pitting) in drilling. Its presence also accelerates the corrosion rate of other corrodents such as hydrogen sulfide and carbon dioxide. Oxygen plays a dual role both as a cathodic depolarizer and an anodic polarizer or passivator. Within a certain range of concentration the... [Pg.1300]

The aggressive ions either break down the protective films or prevent their formation and, in effect, increase the corrosion rate. In presence of chloride and sulfate ions the corrosion attack is more localized and, as a result, causes deep pitting. Inhibitive ions, on the other hand, tend to limit the attack and decrease the corrosion rate by forming protective films. The film is similiar to adherent carbonate-containing rust, which polarizes the anodic areas. When aggressive and inhibitive ions are present together, the aggressive ions, if present in sufficient quantities, interfere with the deposition of the protective layers. [Pg.1309]

Linear polarization instruments provide an instantaneous corrosion-rate data, by utilizing polarization phenomena. These instruments are commercially available as two-electrode Corrater and three electrode Pairmeter (Figure 4-472). The instruments are portable, with probes that can be utilized at several locations in the drilling fluid circulatory systems. In both Corrater and Pairmeter, the technique involves monitoring electrical potential of one of the electrodes with respect to one of the other electrodes as a small electrical current is applied. The amount of applied current necessary to change potential (no more than 10 to 20 mV) is proportional to corrosion intensity. The electronic meter converts the amount of current to read out a number that represents the corrosion rate in mpy. Before recording the data, sufficient time should be allowed for the electrodes to reach equilibrium with the environment. The corrosion-rate reading obtained by these instruments is due to corrosion of the probe element at that instant [184]. [Pg.1312]

Duncan and Frankenthal report on the effect of pH on the corrosion rate of gold in sulphate solutions in terms of the polarization curves. It was found that the rate of anodic dissolution is independent of pH in such solutions and that the rate controlling mechanism for anodic film formation and oxygen evolution are the same. For the open circuit behaviour of ferric oxide films on a gold substrate in sodium chloride solutions containing low iron concentration it is found that the film oxide is readily transformed to a lower oxidation state with a Fe /Fe ratio corresponding to that of magnetite . [Pg.943]

Thus, a useful method of corrosion control is to slow down the driving force of the corrosion cell by reducing the difference in potential at the cathode (cathodic polarization). In practice, this can be achieved by maintaining reducing conditions at the boiler surface (typically by dosing an oxygen scavenger), which increases the rate of cathodic polarization and drives down the corrosion rate. [Pg.150]

Anodic polarization also may occur. Typically, this begins with the formation of a thin, impervious oxide film, chemisorbed at the anode (as on the surface of stainless steels). However, for most metals used in boiler plant systems this chemisorption process must be aided by anodic corrosion inhibitors to reduce corrosion rates to tolerable levels. An example is the application of nitrite-based inhibitors, widely used in HW heating systems. [Pg.151]

Polarization resistance (Rp) techniques can be used to continuously monitor the instantaneous corrosion rate of a metal. Mansfeld provided a thorough review of the use of the polarization resistance technique for the measurement of corrosion currents. R is defined as ... [Pg.209]

A simplification of the polarization resistance technique is the linear polarization technique in which it is assumed that the relationship between E and i is linear in a narrow range around E . Usually only two points ( , 0 are measured and B is assumed to have a constant value of about 20 mV. This approach is used in field tests and forms the basis of commercial corrosion rate monitors. Rp can also be determined as the dc limit of the electrochemical impedance. Mansfeld et al. used the linear polarization technique to determine Rp for mild steel sensors embedded in concrete exposed to a sewer environment for about 9 months. One sensor was periodically flushed with sewage in an attempt to remove the sulfuric acid produced by sulfur-oxidizing bacteria within a biofilm another sensor was used as a control. A data logging system collected Rp at 10-min intervals simultaneously for the two corrosion sensors and two pH electrodes placed at the concrete surface. Figure 2 shows the cumulative corrosion loss (Z INT) obtained by integration of the MRp time curves as ... [Pg.211]


See other pages where Polarization corrosion rates is mentioned: [Pg.1945]    [Pg.2720]    [Pg.277]    [Pg.277]    [Pg.2429]    [Pg.2430]    [Pg.2431]    [Pg.2435]    [Pg.2437]    [Pg.124]    [Pg.54]    [Pg.59]    [Pg.59]    [Pg.104]    [Pg.400]    [Pg.1263]    [Pg.1265]    [Pg.1265]    [Pg.1268]    [Pg.1268]    [Pg.1301]    [Pg.1328]    [Pg.911]    [Pg.123]    [Pg.233]    [Pg.152]    [Pg.216]    [Pg.18]    [Pg.20]    [Pg.20]    [Pg.22]    [Pg.23]   


SEARCH



Corrosion Rate Measurement by Fitting Polarization Curve to Wagner-Traud Equation

Corrosion Rate Measurement by Linear Polarization

Polarization behavior, corrosion rate

Polarization corrosion rates from

Polarization rates

Polarization resistance techniques corrosion-rate measurements

Tafel polarization corrosion rate determination

© 2024 chempedia.info