Plastic block copolymer

More recently, it has been demonstrated that many of the unusual rheological behavior of block copolymers will disappear when the measurements were carried out at temperatures higher than the separation temperature proposed by Leary and Williams (43). Figure 11 shows that for bulk SBS block copolymers with a composition of 7-43-7 (xlO3), the transition occurs around 145°C (especially clear at low frequencies) (76, 77). These data are consistent with those of Pico and Williams on plasticized block copolymers (78). 

Figure 5 shows the structural model for elastomers. Table 3 presents the classification and applications of elastomers. TPE are two-phase or multiphase plastics (block copolymers) with elastic properties similar to those of elastomers, but with a melting temperature that allows for processing as with thermoplastics. Figure 6 illustrates the classification of TPE. 

Styrene block copolymers have been used as compatihilizers for mixed plastics to permit their processing for appHcations such as those outlined earlier (52,61). 

Similarly, the random introduction by copolymerization of stericaHy incompatible repeating unit B into chains of crystalline A reduces the crystalline melting point and degree of crystallinity. If is reduced to T, crystals cannot form. Isotactic polypropylene and linear polyethylene homopolymers are each highly crystalline plastics. However, a random 65% ethylene—35% propylene copolymer of the two, poly(ethylene- (9-prop5lene) is a completely amorphous ethylene—propylene mbber (EPR). On the other hand, block copolymers of the two, poly(ethylene- -prop5iene) of the same overall composition, are highly crystalline. X-ray studies of these materials reveal both the polyethylene lattice and the isotactic polypropylene lattice, as the different blocks crystallize in thek own lattices. 

Fig. 10. Viscosity vs shear rate for solutions of a styrene—butadiene—styrene block copolymer (42). A represents cyclohexanone, where c = 0.248 g/cm (9-xylene, where c = 0.246 g/cm C, toluene, where c = 0.248 g/cm. Courtesy of the Society of Plastics Engineers, Inc.

Adhesives, Coatings, and Sealants. Eor these appHcations, styrenic block copolymers must be compounded with resins and oils (Table 10) to obtain the desired properties (56—58). Materials compatible with the elastomer segments soften the final product and give tack, whereas materials compatible with the polystyrene segments impart hardness. The latter are usually styrenic resins with relatively high softening points. Materials with low softening points are to be avoided, as are aromatic oils, since they plasticize the polystyrene domains and reduce the upper service temperature of the final products. 

Multiblock Copolymers. Replacement of conventional vulcanized mbber is the main appHcation for the polar polyurethane, polyester, and polyamide block copolymers. Like styrenic block copolymers, they can be molded or extmded using equipment designed for processing thermoplastics. Melt temperatures during processing are between 175 and 225°C, and predrying is requited scrap is reusable. They are mostiy used as essentially pure materials, although some work on blends with various thermoplastics such as plasticized and unplasticized PVC and also ABS and polycarbonate (14,18,67—69) has been reported. Plasticizers intended for use with PVC have also been blended with polyester block copolymers (67). 

In the absence of impurities there is frequently no termination step in anionic polymerisations. Hence the monomer will continue to grow until all the monomer is consumed. Under certain conditions addition of further monomer, even after an interval of several weeks, will eause the dormant polymerisation process to proceed. The process is known as living polymerisation and the products as living polymers. Of particular interest is the fact that the follow-up monomer may be of a different species and this enables block copolymers to be produced. This technique is important with certain types of thermoplastic elastomer and some rather specialised styrene-based plastics. 

Among the different pressure sensitive adhesives, acrylates are unique because they are one of the few materials that can be synthesized to be inherently tacky. Indeed, polyvinylethers, some amorphous polyolefins, and some ethylene-vinyl acetate copolymers are the only other polymers that share this unique property. Because of the access to a wide range of commercial monomers, their relatively low cost, and their ease of polymerization, acrylates have become the dominant single component pressure sensitive adhesive materials used in the industry. Other PSAs, such as those based on natural rubber or synthetic block copolymers with rubbery midblock require compounding of the elastomer with low molecular weight additives such as tackifiers, oils, and/or plasticizers. The absence of these low molecular weight additives can have some desirable advantages, such as ... 

Block copolymers can contain crystalline or amorphous hard blocks. Examples of crystalline block copolymers are polyurethanes (e.g. B.F. Goodrich s Estane line), polyether esters (e.g. Dupont s Hytrel polymers), polyether amides (e.g. Atofina s Pebax grades). Polyurethanes have enjoyed limited utility due to their relatively low thermal stability use temperatures must be kept below 275°F, due to the reversibility of the urethane linkage. Recently, polyurethanes with stability at 350°F for nearly 100 h have been claimed [2]. Polyether esters and polyether amides have been explored for PSA applications where their heat and plasticizer resistance is a benefit [3]. However, the high price of these materials and their multiblock architecture have limited their use. All of these crystalline block copolymers consist of multiblocks with relatively short, amorphous, polyether or polyester mid-blocks. Consequently they can not be diluted as extensively with tackifiers and diluents as styrenic triblock copolymers. Thereby it is more difficult to obtain strong, yet soft adhesives — the primary goals of adding rubber to hot melts. 

Another area of recent interest is covulcanization in block copolymers, thermoplastic rubbers, and elasto-plastic blends by developing an interpenetrating network (IPN). A classical example for IPN formation is in polyurethane elastomer blended acrylic copolymers [7]. 

Polyarylate (PAR)-b-PSt and PAR-b-PMMA for compatibiiizers are described 135,39,40). The addition of PAR-b-PSt (1-10 parts) to 100 parts of a blend of PAR-PSt (7w-3w) resulted in improvement of the tensile and flexural modulus (Fig. 4), and PSt dispersed particles were diminished from 1-5 microns to an order that is undetectable by SEM, indicating the excellent, compatibilizing effect of the block copolymer. The alloy thus formed exert the characteristic of PAR, an engineering plastic, as well as easy processability of PSt. Addition of PAR-b-PMMA (3 or 8 parts) to 100 parts of a blend of PAR-polyvinylidenefluoride (PVDF) (7w-3w) resulted in improved microdispersed state of PVDF due to compatibility of PMMA with PVDF, while segregation of PVDF onto the surface was controlled. 

The most desirable annealing temperatures for amorphous plastics, certain blends, and block copolymers is just above their glass transition temperature (Tg) where the relaxation of stress and orientation is the most rapid. However, the required temperatures may cause excessive distortion and warping. 

In a block copolymer, a long segment made from one monomer is followed by a segment formed from the other monomer. One example is the block copolymer formed from styrene and butadiene. Pure polystyrene is a transparent, brittle material that is easily broken polybutadiene is a synthetic rubber that is very resilient, but soft and opaque. A block copolymer of the two monomers produces high-impact polystyrene, a material that is a durable, strong, yet transparent plastic. A different formulation of the two polymers produces styrene-butadiene rubber (SBR), which is used mainly for automobile tires and running shoes, but also in chewing gum. 

Microdomain stmcture is a consequence of microphase separation. It is associated with processability and performance of block copolymer as TPE, pressure sensitive adhesive, etc. The size of the domain decreases as temperature increases [184,185]. At processing temperature they are in a disordered state, melt viscosity becomes low with great advantage in processability. At service temperamre, they are in ordered state and the dispersed domain of plastic blocks acts as reinforcing filler for the matrix polymer [186]. This transition is a thermodynamic transition and is controlled by counterbalanced physical factors, e.g., energetics and entropy. 

Among the many unusual properties that the arborescent architecture leads to, most notable is the discovery that block copolymers with a high MW dendritic (arborescent) polyisobutylene core and poly(para-methylstyrene) end blocks can manifest themselves either as a rubber, or as a plastic, depending on their environment (Figures 7.16 and 7.17). The behavior is thermally irreversible. 

Styrene-butadiene-styrene (SBS) block copolymers are adequate raw materials to produce thermoplastic mbbers (TRs). SBS contains butadiene—soft and elastic—and styrene— hard and tough—domains. Because the styrene domains act as cross-links, vulcanization is not necessary to provide dimensional stability. TRs generally contain polystyrene (to impart hardness), plasticizers, fillers, and antioxidants processing oils can also be added. Due to their nature, TR soles show low surface energy, and to reach proper adhesion a surface modification is always needed. 

Surfactants used as lubricants are added to polymer resins to improve the flow characteristics of the plastic during processing they also stabilise the cells of polyurethane foams during the foaming process. Surfactants are either nonionic (e.g. fatty amides and alcohols), cationic, anionic (dominating class e.g. alkylbenzene sulfonates), zwitterionic, hetero-element or polymeric (e.g. EO-PO block copolymers). Fluorinated anionic surfactants or super surfactants enable a variety of surfaces normally regarded as difficult to wet. These include PE and PP any product required to wet the surface of these polymers will benefit from inclusion of fluorosurfactants. Surfactants are frequently multicomponent formulations, based on petro- or oleochemicals. 

---