Plants Modem

Figure 4. S/C atomic ratios from kerogens of living plants, modem sediments, and buried sediments of the three main types of organic matter encountered in the Abu Dhabi recent sedimentary system, (A) the microbial mats, (B) the Avicennia mangrove, (C) the lagoonal seaweeds.

Modem board and interface SW a bidirectional modem is used to connect the host system, located in the plant, with a remote PC. It is asynchronous, with a throughput of 28000 b/s. The remote PC must match the characteristics of the in-plant PC of the AEBIL system. 

In addition, NDT plays an important part in industrial maintenance. During plant shutdowns for instance, many thousands of ultrasonic wall thickness measurements are taken on piping, vessels, furnace tubes etc. All these thickness readings have to go into extensive data bases, and this process is, thanks to modem computers and data loggers, ever more automated. 

In plant maintenance, the availability of quantitative and non-invasive screening NDT methods will reduce the time needed for shutdowns and increase the intervals between them. Modem NDT methods will become just as important a tool for Risk Based Inspection approaches and maintenance planning as operational parameters and degradation mechanisms already are. 

H. F. Linskens and J. F. Jackson, Wine Analysis, Vol. 6 in Modem Methods of Plant Analysis, Springer Vedag, Berlin, 1988. 

The toxicological problems associated with asbestos have been widely pubHshed and asbestos has been banned from most uses by the EPA. However, modem diaphragm cell chlorine plants have not had difficulty meeting the required exposure limits for asbestos fibers, and, as of 1990, the chlorine industry had an exemption allowing the continued use of asbestos as a diaphragm material. 

Approximately 50—55% of the product from a coal-tar refinery is pitch and another 30% is creosote. The remaining 15—20% is the chemical oil, about half of which is naphthalene. Creosote is used as a feedstock for production of carbon black and as a wood preservative. Because of modifications to modem coking processes, tar acids such as phenol and cresyUc acids are contained in coal tar in lower quantity than in the past. To achieve economies of scale, these tar acids are removed from cmde coal tar with a caustic wash and sent to a central processing plant where materials from a number of refiners are combined for recovery. 

Gut Rubber and Extruded Latex. The manufacturing technology for cut and extmded mbber thread is much older and more widely known than that for spandex fibers. Because production faciUties can be installed with relatively modest capital investment, manufacture of mbber thread is fragmented and more widely distributed with a few major and many minor producers. On a worldwide basis, Fikattice of Italy is the largest mbber thread producer with modem extmded latex plants in Italy, Spain, Malaysia, and the United States. Second in production capacity is the Globe Manufacturing Co., Fall River, Massachusettes with production operations in the United States and the UK. These firms also produce spandex fibers. 

It is possible to add modifiers or delustrants at the dissolving stage. However, modem viscose dope plants feed several spinning machines which are often expected to make different grades of fiber. It is therefore now more common to add the materials needed to make special fibers by injection close to the spinning machines. 

Na AlFg, 5—7% AIF., 5—7% CaF2, 2—6% AI2O2, and 0—7% LiF with an operating temperature of 950°C. Ideally fluorine is not consumed in the process, but substantial quantities of fluorine are absorbed by the cell lining and fluorine is lost to the atmosphere. Modem aluminum industry plants efficiently recycle the fluorine values. 

The roof of the typical furnace collapses unless it is built as a spmng or self-supporting arch, or is flat but suspended, along with the rest of the furnace, from an enclosing stmctural framework. All modem power-plant waterwaH furnaces of any significant megawatt rating are of suspended constmction. 

An example of a modem, tangentially fired, supercritical, lignite-fuel furnace is shown in Figure 5. This unit, at maximum continuous ratings, supplies 2450 metric tons pet hour superheat steam at 26.6 MPa (3850 psi) and 544°C, and 2160 t/h reheat steam at 5.32 MPa (772 psi) and 541°C. These ate the values at the superheater and reheater oudet, respectively. Supercritical fluid-pressure installations ate, however, only rarely needed. Most power plants operate at subcritical pressures in the range of 12.4—19.3 MPa (1800—2800 psi). 

Hair coloring preparations have been in use since the ancient Egyptians, and recorded recipes exist in many cultures. These followed the traditional apphcation of plant extracts or metallic dyes, both of which still are used. In the latter part of the nineteenth century, synthetic organic compounds were discovered which eventually led to modem hair coloring. 

Fig. 5. Flow diagram depicting the principal units and auxiliaries in a modem blast furnace plant, and showing the steps in the manufacture of pig iron from...

Gravity concentration, ie, the separation of ore from gangue based on the differences in specific gravities, using jigs, heavy—medium separators, or spiral concentrators for example, is appHcable for lead ores. However, the predominant beneficiation technique used in modem plants is the bubble or froth flotation (qv) process (4,5). 

Adsorption. Adsorption processes have been used to recover hydrocarbons that are heavier than ethane from natural gas. Although the adsorption process has appHcations for the recovery of pentane and heavier hydrocarbons from lean gas, the percentage recovery of LPG components in these plants usually is low compared to the normal recovery of LPG in modem turboexpander or oil-absorption plants. 

The four process control parameters are temperature, pressure, flow, and level. Modem process level detection systems are varied and ubiquitous in modem chemical plants there are thousands of processes requiring Hquid level indication and Hquid level control. From accumulators to wet wells, the need for level devices is based on the need for plant efficiency, safety, quaUty control, and data logging. Unfortunately, no single level measurement technology works rehably on all chemical plant appHcations. This fact has spawned a broad selection of level indication and control device technologies, each of which operates successfully on specific appHcations. 

Obtainable only in modem plants. Average for U.S. plants is 32.8% Total oxygen concentration is 32 mol %. 

The sulfur dioxide produced by the process is usually converted to sulfuric acid, or sometimes Hquified, and the design of modem roasting faciUties takes into account the need for an efficient and environmentally clean operation of the acid plant (see SuLFURiC ACID AND SULFURTRIOXIDe). 

The standard electrode potential for zinc reduction (—0.763 V) is much more cathodic than the potential for hydrogen evolution, and the two reactions proceed simultaneously, thereby reducing the electrochemical yield of zinc. Current efficiencies slightly above 90% are achieved in modem plants by careful purification of the electrolyte to bring the concentration of the most harmful impurities, eg, germanium, arsenic, and antimony, down to ca 0.01 mg/L. Addition of organic surfactants (qv) like glue, improves the quaUty of the deposit and the current efficiency. 

Molybdenite concentrate contains about 90% M0S2. The remainder is primarily siUca, with lesser amounts of Fe, Al, and Cu. The concentrate is roasted to convert the sulfide to technical molybdic oxide. Molybdenum is added to steel in the form of this oxide. In modem molybdenum conversion plants, the oxidized sulfur formed by roasting M0S2 is converted to sulfuric acid. 

---