Piston power

A force Is applied to the gel s surface by a syringe piston powered by compressed air. Measurements can be Influenced by a skin on the jelly s surface or uneven application of pressure (3 ). Swenson et al. (48) modified the Tarr-Baker apparatus to produce a balance-plunger type Instrument. Although they found a linear stress-strain region within the elastic limits of the gel they also found elasticity was somewhat dependent on the rate of loading. 

The principle of operation of the hydraulic reciprocating pump is similar to the beam pump, with a piston-like sub-surface pump action. The energy to drive the pump, however, is delivered through a hydraulic medium, the power fluid, commonly oil or water. The power fluid drives a downhole hydraulic motor which in turn drives the pump. A separate surface pump delivers the hydraulic power. The power fluid system can be of the closed loop or of the open type. In the latter case, the power fluids are mixed with the produced fluid stream. The performance of the hydraulic pump is primarily monitored by measuring the discharge pressures of both surface and sub-surface pumps. 

In 1840 a hydrauHc power network, which involved large reciprocating pumps that were driven by steam engines, suppHed fluid power to London. However, concurrent technology in steam (qv) turbines and the electric generators outmoded such networks until hydrauHc systems were improved with the use of rotary pumps and oil. The rotary piston pump marked the transition from use of water to oil as the hydrauHc fluid (4). The use of vacuum-distilled, refined mineral oils were instmmental in the success of rotary axial piston pumps and motors such as the Waterbury variable speed gear... 

A homogenize is a high pressure positive pump with three, five, or seven pistons, that is driven by a motor and equipped with an adjustable homogenizing valve. Smoother flow and greater capacity are obtained with more pistons, which force the product iato a chamber that feeds the valve. In design and operation, it is desirable to minimize the power requirements for obtaining an acceptable level of homogenization. At 17.2 MPa (2500 psi) and a volume of 0.91 t/h (2000 lb/h), a 56-kW (75-hp) motor is required. 

Trip Valves The trip valve is part of a system that is used where a specific valve action (i.e., fail up, Fail down, or lock in last position) is required when pneumatic supply pressure to the control valve falls befow a preset level. Trip systems are used primarily on springless piston ac tuators requiring fail-open or fail-closed acrion. An air storage or Volume tank and a check v ve are used with the trip valve to provide power to stroke the valve when supply pressure is lost. Trip valves are designed with hysteresis around the trip point to avoid instabihty when the trip pressure and the reset pressure settings are too close to the same value. 

COMPRESSOR WILL NOT START 1. Power supply failure. 2. Switchgear or starting panel. 3. Low oil pressure shut down switch. 4. Controi panel. NOISE IN CYLINDER 1. Loose piston. 2. Piston hitting outer head or frame end of cylinder. 3. Loose crosshead lock nut. 

Its operation ean be seen as analogous to a meehanieal flywheel and a one-piston engine. The L-C Alter, like the flywheel, stores energy between the power pulses of the driver. The input to the L-C Alter choke input filter) is the ehopped input voltage. The L-C Alter volt-time averages this duty-cyele modulated input voltage waveform. The L-C Altering funetion ean be approximated by... 

Carburetors, pistons, piston rings, and valves Fluid power cylinders and actuators Fluid power pumps and motors Scales and balances, except laboratory Industrial and commercial machinery and equipment, n.e.c ... 

The highest effectiveness can be achieved with the piston strategy. The contaminant concentration, temperature or humidity, and the local effectiveness are functions of the location and the power of the sources in relation to the supply and exhaust openings. With a homogeneous distribution... 

Figure 8 19. Glycol powered pump—piston moving to left. (Source Kimroy, Inc.]...

High-speed units are normally separable. That is, the compressor frame and driver are separated by a coupling or gear box. This is opposed to an integral unit where power cylinders are mounted on the same frame as the compressor cylinders, and the power pistons are attached to the same drive shaft as the compressor cylinders. 

---