Pipe bonding

Keywords Adhesive modulus Adhesys expert system Co-axial joints Compression Concealed joints Creep Elastic limit Epoxy Epoxy composite Einite element analysis Glue line thickness Goland and Reissner Hart-Smith Heat exchanger Hooke s Law Joint designs Joint thickness Lap shear strength Peel Plastic behaviour Polyurethane Pipe bonding Shear stresses Shear modulus Stress distribution Thick adherend shear test Tubular joints Volkersen equation Young s modulus... 

Primary benefits of the second-generation acrylics included increased toughness and impact strength of metal-to-metal bonds, as well as the ability to bond metal surfaces, even oily metal surfaces, with little or no surface preparation. The products were also shown to be capable of effective performance as 100% solids alternatives to solvent cements in application such as plastic pipe bonding and decorative lamination of vinyl and high-pressure laminates to metals and particle board [2]. 

If produced gas contains water vapour it may have to be dried (dehydrated). Water condensation in the process facilities can lead to hydrate formation and may cause corrosion (pipelines are particularly vulnerable) in the presence of carbon dioxide and hydrogen sulphide. Hydrates are formed by physical bonding between water and the lighter components in natural gas. They can plug pipes and process equipment. Charts such as the one below are available to predict when hydrate formation may become a problem. 

The molecular structure input requires atom types to be assigned, which are not the same from one force field to the next. The input also includes a list of bonds in the molecule. There is not a module to automatically assign atom types. Most of the modules use a Cartesian coordinate molecular structure, except for a few that work with torsional space. The same keyword file is read by all the executables. A little bit of input is obtained by the program either interactively or from an ASCII file piped to standard input, which makes for a somewhat cryptic input file. This system of common input files and the user choosing which executables to run give TINKER the ability to run very sophisticated simulations while keeping the input required for simple calculations fairly minimal within the limitations mentioned here. 

Corrosion Resistant Fiber-Reinforced Plastic (FRP). Fiber glass reinforcement bonded with furfuryl alcohol thermosetting resias provides plastics with unique properties. Excellent resistance to corrosion and heat distortion coupled with low flame spread and low smoke emission are characteristics that make them valuable as laminating resins with fiber glass (75,76). Another valuable property of furan FRP is its strength at elevated temperature. Hand-layup, spray-up, and filament-win ding techniques are employed to produce an array of corrosion-resistant equipment, pipes, tanks, vats, ducts, scmbbers, stacks, and reaction vessels for industrial appHcations throughout the world. 

Chemical-Process Vessels. Explosion-bonded products are used in the manufacture of process equipment for the chemical, petrochemical, and petroleum industries where the corrosion resistance of an expensive metal is combined with the strength and economy of another metal. AppHcations include explosion cladding of titanium tubesheet to Monel, hot fabrication of an explosion clad to form an elbow for pipes in nuclear power plants, and explosion cladding titanium and steel for use in a vessel intended for terephthaHc acid manufacture. 

The simplest method of reduciag stresses and reactions is to provide additional pipe ia the system ia the form of loops or offset-bonds. When physical limitations restrict the use of additional bends, a multiple arrangement of several small-size pipe mns may sometimes be used. Owiag to stress intensification, the maximum stress generally occurs at elbows, bends, and Ts. Thus, heavier-walled fittings may reduce the stress without significantly impairing flexibiUty. FiaaHy, effectively located restraints can reduce thermal effects on the equipment. 

When loading or unloading a tank tmck or tank car, static bonding lines must be attached between the vehicle and the fixed piping system. Tank tmck drivers may be inexperienced in the handling of chemicals and, therefore, it is essential that the plant personnel be alert in checking the driver s operations and in correcting any possible deficiencies (see Transportation). 

Polypropylene can be fabricated by almost any process used for plastics (see Plastics processing). The extmsion of pipe and injection mol ding of fittings present no unusual problem. However, there is no way to bond the fittings to the pipe except by remelting the polymer, which is impractical on most constmction sites. The resin can be reinforced by glass fibers, mineral fillers, or other types of fillers and can be pigmented readily. 

In joining reinforced thermosetting pipe it is particularly important that the pipe be cut without chipping or cracking it. It is also important to sand, file, or grind any mold-release agent from the surfaces to be cemented. Joints are built up layer by layer of adhesive-saturated reinforcement by following the manufacturer s recommended procedure. Application of adhesive to the surfaces to be joined and assembly of these surfaces shall produce a continuous bond and provide an adhesive seal to protect the reinforcement from attack by the contents of the pipe. Unfilled or unbonded areas of the joint are considered defects and must be repaired. 

Protect against the accumulation of electrostatic charges which can cause ignition. This may include the bonding and grounding of the tank, piping. 

Sample containers are discussed in 5-8.4.2. Eor tanks containing a flammable atmosphere this is most safely accomplished using a sampling well, also known as a gauge well. This is a metal pipe, sometimes perforated, through which a sample container or gauging device is lowered into the liquid. The metal pipe is permanently fixed and electrically bonded to the top and... 

---