PH buffering

Table 8.14 National Bureau of Standards (U.S.) Reference pH Buffer Solutions 8.105...

Table 8.15 Compositions of Standard pH Buffer Solutions [National Bureau of...

The buffer values for the NBS reference pH buffer solutions are given below ... 

To prepare the standard pH buffer solutions recommended by the National Bureau of Standards (U.S.), the indicated weights of the pure materials in Table 8.15 should be dissolved in water of specific conductivity not greater than 5 micromhos. The tartrate, phthalate, and phosphates can be dried for 2 h at 100°C before use. Potassium tetroxalate and calcium hydroxide need not be dried. Fresh-looking crystals of borax should be used. Before use, excess solid potassium hydrogen tartrate and calcium hydroxide must be removed. Buffer solutions pH 6 or above should be stored in plastic containers and should be protected from carbon doxide with soda-lime traps. The solutions should be replaced within 2 to 3 weeks, or sooner if formation of mold is noticed. A crystal of thymol may be added as a preservative. 

Direct Titrations. The most convenient and simplest manner is the measured addition of a standard chelon solution to the sample solution (brought to the proper conditions of pH, buffer, etc.) until the metal ion is stoichiometrically chelated. Auxiliary complexing agents such as citrate, tartrate, or triethanolamine are added, if necessary, to prevent the precipitation of metal hydroxides or basic salts at the optimum pH for titration. Eor example, tartrate is added in the direct titration of lead. If a pH range of 9 to 10 is suitable, a buffer of ammonia and ammonium chloride is often added in relatively concentrated form, both to adjust the pH and to supply ammonia as an auxiliary complexing agent for those metal ions which form ammine complexes. A few metals, notably iron(III), bismuth, and thorium, are titrated in acid solution. 

Reagent layer 1 porous gelatin coating film of urease and pH buffer... 

Uses. The principal use of monosodium phosphate is as a water-soluble soHd acid and pH buffer, primarily in acid-type cleaners. The double salt, NaH2P04 H PO, referred to as hemisodium orthophosphate or sodium hemiphosphate, is often generated in situ from monosodium phosphate and phosphoric acid in these types of formulations. Mixtures of mono- and disodium phosphates are used in textile processing, food manufacture, and other industries to control pH at 4—9. Monosodium phosphate is also used in boiler-water treatment, as a precipitant for polyvalent metal ions, and as an animal-feed supplement. 

The iodometric analysis method for CIO2 and its coproducts is based on the pH-dependant oxidation of potassium iodide to selectively distinguish the various oxychlorine species from each other (42,89). The reactions of the oxidizer species with iodide at various pH buffered conditions ate... 

Use of a pH buffer of 8—9 has been suggested as a substitute for the pH 7 buffer for more accurate analysis. Sodium thiosulfate [10102-17-7] Na2S202, or phenylarsine oxide [637-03-6] C H AsO, are the typical titrants. 

Concentration limits of the diphosphate-ion, admissible to determination of magnesium and cobalt, manganese and cobalt, zinc and cobalt by spectrophotometric method with application of the l-(2-pyridylazo)-resorcinol (PAR) are presented. Exceeding maintenance of the diphosphate-ion higher admissible supposes a preliminary its separation on the anionite in the H+-form. The optimum conditions of cobalt determination and amount of the PAR, necessary for its full fastening are established on foundation of dependence of optical density of the cobalt complex with PAR from concentration Co + and pH (buffer solutions citrate-ammoniac and acetate-ammoniac). 

Heavy metal contamination of pH buffers can be removed by passage of the solutions through a Chelex X-100 column. For example when a solution of 0.02M HEPES [4-(2-HydroxyEthyl)Piperazine-l-Ethanesulfonic acid] containing 0.2M KCl (IL, pH 7.5) alone or with calmodulin, is passed through a column of Chelex X-100 (60g) in the K" " form, the level of Ca ions falls to less than 2 x 10" M as shown by atomic absorption spectroscopy. Such solutions should be stored in polyethylene containers that have been washed with boiling deionised water (5min) and rinsed several times with deionised water. TES [, N,N, -Tetraethylsulfamide] and TRIS [Tris-(hydroxymethyl)aminomethane] have been similarly decontaminated from metal ions. 

A second way to achieve constancy of a reactant is to make use of a buffer system. If the reaction medium is water and B is either the hydronium ion or the hydroxide ion, use of a pH buffer can hold Cb reasonably constant, provided the buffer capacity is high enough to cope with acids or bases generated in the reaction. The constancy of the pH required depends upon the sensitivity of the analytical method, the extent of reaction followed, and the accuracy desired in the rate constant determination. 

Those which maintain certain conditions but do not take part in electrode reactions examples are electrolytes added to improve conductivity, pH buffer systems and ions which maintain complex ion equilibria. 

The third main type of alkalising agent is the alkali phosphate. Sodium mono-, di- and triphosphates in appropriate proportions may be used to achieve the desired conditions. In addition to their use to prevent scale phosphates have the advantage for corrosion control of being pH buffers so that they limit the attainable concentration of free hydroxide ion in solution and so restrain the scope for corrosion of the caustic type. 

Metal Titration type pH Buffer Indicator (Note 1) Colour change (Note 2) Notes... 

In low ionic strength solutions (I < 0.005 panel A), the curves obtained with the pH buffers MOPS and glycylglycine and also with a weak Ca2+-chelator citric acid are nearly superimposable on each other, whereas those obtained with the buffers that contain strong chelators EDTA and NTA are shifted almost 2 pCa units to the right. The curve for NTA is somewhat atypical probably the Ca2+-NTA ratio of the Ca2+-NTA complex used was not exactly 1.0. In the... 

---