Permeability measurements

The pores between the rock components, e.g. the sand grains in a sandstone reservoir, will initially be filled with the pore water. The migrating hydrocarbons will displace the water and thus gradually fill the reservoir. For a reservoir to be effective, the pores need to be in communication to allow migration, and also need to allow flow towards the borehole once a well is drilled into the structure. The pore space is referred to as porosity in oil field terms. Permeability measures the ability of a rock to allow fluid flow through its pore system. A reservoir rock which has some porosity but too low a permeability to allow fluid flow is termed tight . 

Other logs employed to determine N/G ratio include the spontaneous potential (SP) log and the microlog, which differentiate permeable from non-permeable intervals. The N/ G ratio can also be measured directly on cores if there is visible contrast between the reservoir and non-reservoir sections, or from permeability measurements on core samples, providing sample coverage is sufficient. 

Permeabilities measured on small core samples, whilst accurate, are not necessarily representative of the reservoir. Averaging a number of samples can allow comparisons with well test permeabilities to be made. 

A sensitive metal sorting bridge Conductivity measurements Permeability measurements Pulsed eddy currents Skin effect All 120 years ago. 

Let us first consider experiments without composition gradients. These are permeability measurements, in which flow is induced by a pressure gradient Consider first the flow of pure substance 1, setting x = 1, = 0 and... 

Air flow/air permeability Measure of the amount of air that flows through a filter - a variable of the degree of contamination, differential pressure, total porosity, and filter area. Expressed in either cubic feet/minute/square foot or liters/minute/square centimeter at a given pressure. 

This is very important as several other properties are dependent upon it. If the porosity is too high, the article will be weak and will not retain liquid. The pore structure should also be taken into account. When a ceramic material is hred, although the internal surface area decreases as the material approaches zero porosity, the mean radius of the pores increases. Thus, when the internal surface area is 3 mVg the mean pore radius may be of the order of 10 m, while when the internal surface has dropped to 0-5 mVg the mean pore radius may be about 4-5 x 10 m. The mean pore radius may reach a value as high as 9 x 10 m as the ware approaches zero porosity during firing. It is thus obvious that at some point the pores must start to close up. This closing of the pores with the approach of vitrification is borne out by results of permeability measurements. 

The evaluation of the apparent ionization constants (i) can indicate in partition experiments the extent to which a charged form of the drug partitions into the octanol or liposome bilayer domains, (ii) can indicate in solubility measurements, the presence of aggregates in saturated solutions and whether the aggregates are ionized or neutral and the extent to which salts of dmgs form, and (iii) can indicate in permeability measurements, whether the aqueous boundary layer adjacent to the membrane barrier, Umits the transport of drugs across artificial phospholipid membranes [parallel artificial membrane permeation assay (PAMPA)] or across monolayers of cultured cells [Caco-2, Madin-Darby canine kidney (MDCK), etc.]. 

HISTORICAL DEVELOPMENTS IN ARTIFICIAL-MEMBRANE PERMEABILITY MEASUREMENT... 

Measurements of Pe in fixed-pH solutions but at various different stirring speeds need to be made. The double-reciprocal analysis, HPe versus 1/v , for Caco-2 permeability measurements in the Transwell (Corning Costar) system produced a linear plot for x- 0.8 [514]. The intercept yields the membrane permeability for the particular pH value in the study the slope determines the k constant. From the analysis of testosterone transport, for the stirring speed of 25 rpm (planar rotating shaker), the thickness of each UWL (assuming symmetric geometry) was calculated to be 465 pm at 150 rpm, haq= 110 pm [514], Karlsson and Artursson [512] found x = 1.0 to best represent their stirring-based analysis of the UWL permeability. 

Iso-pH Permeability Measurements using Soy Lecithin-Dodecane-Impregnated Filters... 

The above iso-pH measurements are based on the 2% DOPC/dodecane system (model 1.0 over pH 3-10 range). Another membrane model was also explored by us. Table 7.16 lists iso-pH effective permeability measurements using the soy lecithin (20% wt/vol in dodecane) membrane PAMPA (models 17.1, 24.1, and 25.1) The negative membrane charge, the multicomponent phospholipid mixture, and the acceptor sink condition (Table 7.1) result in different intrinsic permeabilities for the probe molecules. Figure 7.40 shows the relationship between the 2% DOPC and the 20% soy iso-pH PAMPA systems for ketoprofen. Since the intrinsic permeability of ketoprofen in the soy lecithin membrane is about 20 times greater than in DOPC membrane, the flat diffusion-limited transport region of the log Pe... 

How Well Do Caco-2 Permeability Measurements Predict Human Jejunal Permeabilities ... 

In conclusion, the double-sink su m-P, PAMPA in vitro GIT assay seems to predict human absorption as well as in vivo human permeability measurements (see Figs. 7.66a,b) and in vitro Caco-2 permeability measurements (see Figs. 7.60 and 7.63), but at a lower cost and higher speed. 

The BCS scheme can be made more useful by incorporating a further improved basis of physicochemical profiling. For example, the role of pH in permeability measurements could be better defined. The use of simulated intestinal fluids for solubility measurements could be better promoted. The effects of fed/fasted states on absorption could be better address, in methods that have optimum clinical relevance. 

Xiang, T.-X. Anderson, B. D., Development of a combined NMR paramagnetic ion-induced line-broadening dynamic light scattering method for permeability measurements across lipid bilayer membranes, J. Pharm. Sci. 84, 1308-1315 (1995). 

In addition to the above measurements, indexes using soil concentrations in combination with permeability measurements have been suggested by some researchers.4142 As elaborated on later in this section, these methods have been successful in establishing relationships between some of the site measurements and indexes, and indoor radon concentrations for specific areas and regions. 

Lee CP, RLA Devrueh, PL Smith. (1997). Selection of development candidates based on in vitro permeability measurements. Adv Drug Delivery Rev 23 47-62. 

Use of carefully selected surfactants in well treatment fluids is a way to accomplish this. Rock wettability can be altered by adsorption of polar materials such as surfactants and corrosion inhibitors, or by the deposition of polar crude oil components (173). Pressure appears to have little influence on rock wettability (174). The two techniques used to study wettability, contact and and relative permeability measurements, show qualitative agreement (175-177). Deposition of polar asphaltenes can be particularly significant in carbon dioxide enhanced oil recovery. 

Key Historical Developments in Artificial-Membrane Permeability Measurement 47... 

To reach such a site, a molecule must permeate through many road blocks formed by cell membranes. These are composed of phospholipid bilayers - oily barriers that greatly attenuate the passage of charged or highly polar molecules. Often, cultured cells, such as Caco-2 or Madin-Darby canine kidney (MDCK) cells [1-4], are used for this purpose, but the tests are costly. Other types of permeability measurements based on artificial membranes have been considered, the aim being to improve efficiency and lowering costs. One such approach, PAMPA, has been described by Kansy et al. [5],... 

---