Peel back

In order to see the effect of the compatibilizer more clearly, SEM (scanning electron microscopy) micrographs of the peeled back exposed surface of the spun fibers are shown in Fig. 7. In a noncompatibilized blend, the long TLCP fibrils are bundled together (Fig. 7A). The fibril surface looks quite clean and smooth along the... 

Figure 7 SEM photographs of peeled back surfaces of PEI-TLCP blend fibers. Draw ratio is 4 (x 2000). The amount of PEsI in the blends are (A) 0 phr, (B) 0.75 phr, and (C) 3.75 phr. Source Ref. 11.

Note that olanzapine is available as a tablet to swallow or as an orally disintegrating tablet. When using the orally disintegrating tablet, peel back the foil on the blister. Using dry hands, remove the tablet and place the entire tablet in the mouth. The tablet will disintegrate with or without liquid. 

Figure 6. Same set as in Figure 5 with cellophane wrapper peeled back. II sticks slightly and IV sticks considerably...

Figure 8. Set shown in Figure 7 with wrapper peeled back. Note...

The adhesion of the UVC lacquer was tested immediately after radiation with Scotch tape in a "peel back" puU-adhesion test and was evaluated by a... 

Immediately before using the tiotropium dose, peel back the aluminum foil using the tab until 1 capsule is fully visible. Peel back the foil lidding only as far as the STOP line printed on the blister foil to prevent exposure of more than 1 capsule. Immediately use the drug after opening the packaging over an... 

Administration - Administer the tablets with water by swallowing the tablet whole. Administer the orally disintegrating tablet as follows After opening the pouch, peel back the foil on the blister. Do not push the tablet through foil. 

When cleaning the fish, always wear good rubber gloves. Cut off the head and carefully peel back the skin, like a glove, from neck to tail. The internal organs will drop out. Pick out the liver intestines and gonads (see illustration) and discard the rest of the fish. 

Yet, in the end, the hound proved mortal, not supernatural its unearthly flickering flame the result of a cunning preparation of phosphorus. (For other cunning preparations of phosphorus, see the discussion of phosphinidenes in Chapter 11 in this volume.) We too have peeled back much of the mystery and cleared away most of the fog that once surrounded the strucmres, electronic... 

Further improvement of this principle of factory-metered blistered unit doses was achieved when GlaxoSmithKline developed the Accuhaler device (also named Diskus in some countries (Fig. 8.7). This multiple-dose DPI device contains a blister strip of 60 unit doses that is transported to the next filled unit dose by pulling a small ergonomic lever prior to inhalation. The powder is presented for aerosolization by peeling back the foil from the blister, which is superior to simple piercing because it is not associated with variability in foil flap shape and device retention. The dose indicator on top of the device tells the patient how many doses are left and decreases each time the lever is pulled. This means that as with most other devices, operation of the dose indicator is associated with the loading operation and not with the inhalation maneuver. 

Many vertical low-pressure storage tanks containing flammable or combustible liquids are designed with a weak weld seam on the wall-to-roof connection. This loss prevention feature allows the roof to separate and peel back if an internal fire, an internal explosion, or just a pneumatic overpressure situation occurs within the tank. If the roof relieves or is blown off, the liquid is still contained within the walls if these tanks are properly designed and fabricated. These conical roof tanks are often built to the American Petroleum Institute (API) Standard 650 Welded Steel Storage Tanks. ... 

Peeling Film peels back from edge exposing tablet surface... 

Batteries are typically produced with deep drawn metal cans on which a pressure sensitive adhesive label is applied for product identification, branding and safety information. Customers began complaining of batteries becoming jammed in various types of equipment. Devices returned to the manufacturer showed that the pressure sensitive labels had peeled back, resulting in adhesion between the overturned label and the device. Further examination of batteries on store shelves for more than a year also indicated peeling labels in a low frequency of batteries. These labels consisted of laminates of paper and polyester. The labels are normally flat and stiff and when applied over a battery, the labels will return to the flat condition if the adhesive fails. This results in peel-back at the edges of the label. 

When ironing is complete, peel back the transfer film. 

Because of its surface sensitivity, AES has been a valuable tool for identification of contaminants at Interfaces where delamlnatlon has occurred. Sometimes no contaminants are detected at Interfaces where delamlnatlon has occurred. Lack of evidence for contaminants can indicate mechanical reasons for the delamlnatlon. Specimens can be prepared by using adhesive tape to separate films or using a sharp point to peel back blister like features. Whenever possible both sides of the failed Interface should be analyzed. 

Peel back flip over coat with Ti/Au laminate crystal... 

References to the pinch stage of the impact refer to the terminal stage when the nose cap has been completely split open longitudinally and peeled back to the steel projectile body, which is raindly being brought to a halt TNT... 

A man was going for him. Beefy and hard-set, crouched low for a pro football tackle. A1 waved a hand, almost casually, and white fire squirted into the hero s face. Black petals of flesh peeled back from the bone, sizzling. Thick chestnut hair flamed to ash. A dull agonized grunt, cutting off as pain overloaded his consciousness, and the man collapsed. 

Exactly what has got you so all-fired het up " Captain Layia asked. Her couch webbing peeled back allowing her to glide over towards the three of them. 

Yeah." Joshua datavised an instruction into the flight computer. Harlequin schematics of the starship s principal systems vanished from his mind, and the webbing peeled back. 

Fig. 3.8 Illustration of the steps for transfer printing SNAP nanowires onto plastic substrates, (a) Nanowires are etched into a single-crystal sihcon-on-msulator substrate, (b) The exposed oxide is etched and a piece of poly(dimethylsiloxane) (PDMS) makes conformal contact with the nanowire surfaces, (c) The PDMS with adhered nanowires is peeled back from the host substrate, (d) A plastic substrate is spin-cast with epoxy, (e) The PDMS makes conformal contact with the plastic and the epoxy is cured, (g) Peeling back the PDMS leaves behind the SNAP nanowires in their original orientation, but on plastic. Image courtesy of Prof. Jim Heath, California Institute of Technology ...

---