Particulate problem

Bradway, R. M., and Record, F. A. (1976). National Assessment of the Urban Particulate Problem. EPA-450/3-76-025, Research Triangle Park, North Carolina. 

In 1970, new efforts were underway to solve Portland s suspended particulate problem. Early efforts relied on available emission factors and industrial source testing, as a basis for the emission Inventory. The inventory was then used, with a proportional rollback model, as a basis for the new strategy. New industrial controls were Installed which resulted in a 60,000 tons per year region-wide reduction in industrial emissions. Although progress toward cleaner air was made, air quality standard violations caused by then unknown sources continued and modeling efforts failed to account for over one-half of the particulate mass. 

There are disadvantages of IR tunnels they are large, their belt speeds are slow, product heat-up may be less uniform, and they may create particulate problems. These particles are generated from the deterioration of the heating element and the moving belt. This problem can be helped by installing HEPA filters at the entrance of the tunnel and at the cooling zone junction... 

Utility systems as sources of waste. The principal sources of utility waste are associated with hot utilities (including cogeneration systems) and cold utilities. Furnaces, steam boilers, gas turbines, and diesel engines all produce waste from products of combustion. The principal problem here is the emission of carbon dioxide, oxides of sulfur and nitrogen, and particulates (metal oxides, unbumt... 

For other physical properties, the specification differences between diesel fuel and home-heating oil are minimal. Note only that there is no minimum distillation end point for heating oil, undoubtedly because tbe problem of particulate emissions is much less critical in domestic burners than in an engine. 

Gasoline engine equipment such as carburetors, injectors, intake manifolds, valve systems and combustion chambers, are subject to fouling by the fuel itself, the gases recycled from the crankcase, or even dust and particulates arriving with poorly filtered air. Three types of problems then result ... 

Diesel fuels, like gasoline, are formulated with additives that affect the process of combustion, in this case to improve the cetane number. Diesel fuels also contain detergents for irijection systems as well as compounds for improving the fuel s low tempierature rheology. Finally, decreasing particulate emissions is a problem of increasing concern, but the mechanism of action to promote this effect is not clearly understood. 

Figure 5.22 Problem domain in the micro-mechanical analysis of the particulate polymer composite...

An aerosol is a suspension of either a solid or a liquid in a gas. Fog, for example, is a suspension of small liquid water droplets in air, and smoke is a suspension of small solid particulates in combustion gases. In both cases the liquid or solid particulates must be small enough to remain suspended in the gas for an extended time. Solid aerosol particulates, which are the focus of this problem, usually have micrometer or submicrometer diameters. Over time, solid particulates settle out from the gas, falling to the Earth s surface as dry deposition. 

Accuracy Under normal conditions relative errors of 1-5% are easily obtained with UV/Vis absorption. Accuracy is usually limited by the quality of the blank. Examples of the type of problems that may be encountered include the presence of particulates in a sample that scatter radiation and interferents that react with analytical reagents. In the latter case the interferant may react to form an absorbing species, giving rise to a positive determinate error. Interferents also may prevent the analyte from reacting, leading to a negative determinate error. With care, it maybe possible to improve the accuracy of an analysis by as much as an order of magnitude. 

Pollutants. The problems posed by ak pollutants are very serious. Within a museum, measures can be taken to remove harmful substances as efficiently as possible by means of the installation of appropriate filter systems in the ventilation equipment. Proposed specification values for museum climate-control systems requke filtering systems having an efficiency for particulate removal in the dioctyl phthalate test of 60—80%. Systems must be able to limit both sulfur dioxide and nitrogen dioxide concentrations <10 /ig/m, and ozone to <2 /ig/m. ... 

In some cases particles have been added to electrical systems to improve heat removal, for example with an SF -fluidized particulate bed to be used in transformers (47). This process appears feasible, using polytetrafluoroethylene (PTFE) particles of low dielectric constant. For a successful appHcation, practical problems such as fluidizing narrow gaps must be solved. 

---