P-Toluenesulfonate anion

Cyanide and thiocyanate anions in aqueous solution can be determined as cyanogen bromide after reaction with bromine [686]. The thiocyanate anion can be quantitatively determined in the presence of cyanide by adding an excess of formaldehyde solution to the sample, which converts the cyanide ion to the unreactive cyanohydrin. The detection limits for the cyanide and thiocyanate anions were less than 0.01 ppm with an electron-capture detector. Iodine in acid solution reacts with acetone to form monoiodoacetone, which can be detected at high sensitivity with an electron-capture detector [687]. The reaction is specific for iodine, iodide being determined after oxidation with iodate. The nitrate anion can be determined in aqueous solution after conversion to nitrobenzene by reaction with benzene in the presence of sulfuric acid [688,689]. The detection limit for the nitrate anion was less than 0.1 ppm. The nitrite anion can be determined after oxidation to nitrate with potassium permanganate. Nitrite can be determined directly by alkylation with an alkaline solution of pentafluorobenzyl bromide [690]. The yield of derivative was about 80t.with a detection limit of 0.46 ng in 0.1 ml of aqueous sample. Pentafluorobenzyl p-toluenesulfonate has been used to derivatize carboxylate and phenolate anions and to simultaneously derivatize bromide, iodide, cyanide, thiocyanate, nitrite, nitrate and sulfide in a two-phase system using tetrapentylammonium cWoride as a phase transfer catalyst [691]. Detection limits wer Hi the ppm range. 

Preparation and Reactions of S-b-MM. As mentioned in the introduction, we were interested in block copolymers of styrene and alkali metal methacrylates with overall molecular weights of about 20,000 and methacrylate contents on the order of 10 mol%. The preparation of such copolymers by the usual anionic techniques is not feasible. An alternative is to prepare block copolymers of styrene and methacrylic esters by sequential anionic polymerization, followed by a post-polymerization reaction to produce the desired block copolymers. The obvious first choice of methacrylic esters is methyl methacrylate. It is inexpensive, readily available, and its block copolymers with styrene are well-known. In fact, Brown and White have reported the preparation and hydrolyses of a series of S-b-MM copolymers of varying MM content using p-toluenesulfonic acid (TsOH) (6). The resulting methacrylic acid copolymers were easily converted to their sodium carboxylates by neutralization with sodium hydroxide. 

The water-soluble palladium complex prepared from [Pd(MeCN)4](Bp4)2 and tetrasulfonated DPPP (34, n=3, m=0) catalyzed the copolymerization of CO and ethene in neutral aqueous solutions with much lower activity [21 g copolymer (g Pd) h ] [53] than the organosoluble analogue in methanol. Addition of strong Brpnsted acids with weakly coordinating anions substantially accelerated the reaction, and with a catalyst obtained from the same ligand and from [Pd(OTs)2(MeCN)2] but in the presence of p-toluenesulfonic acid (TsOH) 4 kg copolymer was produced per g Pd in one hour [54-56] (Scheme 7.16). Other tetrasulfonated diphosphines (34, n=2, 4 or 5, m=0) were also tried in place of the DPPP derivative, but only the sulfonated DPPB (n=4) gave a catalyst with considerably higher activity [56], Albeit with lower productivity, these Pd-complexes also catalyze the CO/ethene/propene terpolymerization. 

More synthetic interest is generated by the potentially very useful hydration of dienes. As shown on Scheme 9.6, methylethylketone (MEK) can be produced from the relatively cheap and easily available 1,3-butadiene with combined catalysis by an acid and a transition metal catalyst. Ruthenium complexes of several N-N chelating Hgands (mostly of the phenanthroline and bipyridine type) were found active for this transformation in the presence of Bronsted acids with weakly coordinating anions, typically p-toluenesulfonic acid, TsOH [18,19]. In favourable cases 90 % yield of MEK, based on butadiene, could be obtained. 

The sulfones 367 (R = H and Me) obtained from 3-(indol-3-yl)propionate esters with the anion of dimethyl sulfoxide were cyclized, losing methylthiol, via 368 in the presence of p-toluenesulfonic acid in hot acetonitrile, ... 

If the diazonium salt is derived from alkoxyanilines in which the alkoxy moiety contains heptyl, decyl, or cetyl groups and the anion is fluoroborate, perchlorate, or p-toluenesulfonate, the salt is soluble in organic solvents such as benzene or ether and the azo compounds derived therefrom may be prepared in nonaqueous systems [8a]. 

Different behavior was found for the p-toluenesulfonate and chloride derivatives containing ligands derived from pyrimidine. This could be due to a competitive coordination of these anions against the heterocyclic ligands. For the chloride complexes, a clear resonance broadening is observed at room temperature. Considering the chemical shifts it must be accepted that the free ligand is the dominant species. 

Irradiation of certain 1-p-toluenesulfonate-1,2,3-triazole anions has been employed in the preparation of alkynes.95... 

The reaction proceeds to form the alkyl p-toluenesulfonate as expected, but the chloride anion formed in this step subsequently acts as a nucleophile and displaces p-toluenesulfonate from RCH2OTs. 

Table3.11 Nucleophilicityofvarious anions (A ) in the presence of [18] crown-6 (leaving group, X = p toluenesulfonate).

---