Olefin catalytic cycle

Wilkinson Hyd.rogena.tion, One of the best understood catalytic cycles is that for olefin hydrogenation in the presence of phosphine complexes of rhodium, the Wilkinson hydrogenation (14,15). The reactions of a number of olefins, eg, cyclohexene and styrene, are rapid, taking place even at room temperature and atmospheric pressure but the reaction of ethylene is extremely slow. Complexes of a number of transition metals in addition to rhodium are active for the reaction. 

The Wilkinson hydrogenation cycle shown in Figure 3 (16) was worked out in experiments that included isolation and identification of individual rhodium complexes, measurements of equiUbria of individual steps, deterrnination of rates of individual steps under conditions of stoichiometric reaction with certain reactants missing so that the catalytic cycle could not occur, and deterrnination of rates of the overall catalytic reaction. The cycle demonstrates some generally important points about catalysis the predominant species present in the reacting solution and the only ones that are easily observable by spectroscopic methods, eg, RhCl[P(CgH 2]3> 6 5)312 (olefin), and RhCl2[P(CgH )2]4, are outside the cycle, possibly in virtual equiUbrium with... 

The most widely accepted mechanism of reaction is shown in the catalytic cycle (Scheme 1.4.3). The overall reaction can be broken down into three elementary steps the oxidation step (Step A), the first C-O bond forming step (Step B), and the second C-O bond forming step (Step C). Step A is the rate-determining step kinetic studies show that the reaction is first order in both catalyst and oxidant, and zero order in olefin. The rate of reaction is directly affected by choice of oxidant, catalyst loadings, and the presence of additives such as A -oxides. Under certain conditions, A -oxides have been shown to increase the rate of reaction by acting as phase transfer catalysts. ... 

As stated above, olefin metathesis is in principle reversible, because all steps of the catalytic cycle are reversible. In preparatively useful transformations, the equilibrium is shifted to one side. This is most commonly achieved by removal of a volatile alkene, mostly ethene, from the reaction mixture. An obvious and well-established way to classify olefin metathesis reactions is depicted in Scheme 2. Depending on the structure of the olefin, metathesis may occur either inter- or intramolecularly. Intermolecular metathesis of two alkenes is called cross metathesis (CM) (if the two alkenes are identical, as in the case of the Phillips triolefin process, the term self metathesis is sometimes used). The intermolecular metathesis of an a,co-diene leads to polymeric structures and ethene this mode of metathesis is called acyclic diene metathesis (ADMET). Intramolecular metathesis of these substrates gives cycloalkenes and ethene (ring-closing metathesis, RCM) the reverse reaction is the cleavage of a cyclo-... 

The general catalytic cycle for the coupling of aryl-alkenyl halides with alkenes is shown in Fig. 9.6. The first step in this catalytic cycle is the oxidative addition of aryl-alkenyl halides to Pd(0). The activity of the aryl-alkenyl halides still follows the order RI > ROTf > RBr > RC1. The olefin coordinates to the Pd(II) species. The coordinated olefin inserts into Pd—R bond in a syn fashion, p-Hydrogen elimination can occur only after an internal rotation around the former double bond, as it requires at least one /I-hydrogen to be oriented syn perpendicular with respect to the halopalladium residue. The subsequent syn elimination yields an alkene and a hydridopalladium halide. This process is, however, reversible, and therefore, the thermodynamically more stable (E)-alkene is generally obtained. Reductive elimination of HX from the hydridopalladium halide in the presence of a base regenerates the catalytically active Pd(0), which can reenter the catalytic cycle. The oxidative addition has frequently assumed to be the rate-determining step. 

The formation of isomeric aldehydes is caused by cobalt organic intermediates, which are formed by the reaction of the olefin with the cobalt carbonyl catalyst. These cobalt organic compounds isomerize rapidly into a mixture of isomer position cobalt organic compounds. The primary cobalt organic compound, carrying a terminal fixed metal atom, is thermodynamically more stable than the isomeric internal secondary cobalt organic compounds. Due to the less steric hindrance of the terminal isomers their further reaction in the catalytic cycle is favored. Therefore in the hydroformylation of an olefin the unbranched aldehyde is the main reaction product, independent of the position of the double bond in the olefinic educt ( contrathermodynamic olefin isomerization) [49]. 

Iron hydride complexes can be synthesized by many routes. Some typical methods are listed in Scheme 2. Protonation of an anionic iron complex or substitution of hydride for one electron donor ligands, such as halides, affords hydride complexes. NaBH4 and L1A1H4 are generally used as the hydride source for the latter transformation. Oxidative addition of H2 and E-H to a low valent and unsaturated iron complex gives a hydride complex. Furthermore, p-hydride abstraction from an alkyl iron complex affords a hydride complex with olefin coordination. The last two reactions are frequently involved in catalytic cycles. 

The proposed catalytic cycle, which is based on experimental data, is shown in Scheme 6. Loss of 2 equiv. of N2 from 5 (or alternatively 1 equiv. of N2 or 1 equiv. of H2 from complexes shown in Scheme 3) affords the active species a. Olefin coordination giving b is considered to be preferred over oxidative addition of H2. Then, oxidative addition of H2 to b provides the olefin dihydride intermediate c. Olefin insertion giving d and subsequent alkane reductive elimination yields the saturated product and regenerates the catalytically active species a. 

The initially formed tetra-alkylferrate(II) represents the reactive intermediate in both reactions that undergoes a carboferration of the triple bond in eq. 2, Scheme 29. Transmetallation from Fe to Mg yields a vinyl-magnesium species, which liberates the desired olefin upon hydrolysis within the acidic work-up procedure. In the above two reactions, a competing p-hydride elimination from the ferrate yields the unreactive Fe-H species and hence is considered to be the deactivation step in the catalytic cycle. 

The proposed catalytic cycle is shown in Scheme 31. Hence, FeCl2 is reduced by magnesium and subsequently coordinates both to the 1,3-diene and a-olefin (I III). The oxidative coupling of the coordinated 1,3-diene and a-olefin yields the allyl alkyl iron(II) complex IV. Subsequently, the 7i-a rearrangement takes place (IV V). The syn-p-hydride elimination (Hz) gives the hydride complex VI from which the C-Hz bond in the 1,4-addition product is formed via reductive elimination with regeneration of the active species II to complete the catalytic cycle. Deuteration experiments support this mechanistic scenario (Scheme 32). 

Olefin metathesis is a rearrangement reaction that includes a transition metal carbene and an olefin. After the catalytic cycle, a new olefin and a new active metal carbene are formed (Scheme 3.5) [90],... 

ROMP is without doubt the most important incarnation of olefin metathesis in polymer chemistry [98]. Preconditions enabling this process involve a strained cyclic olefinic monomer and a suitable initiator. The driving force in ROMP is the release of ring strain, rendering the last step in the catalytic cycle irreversible (Scheme 3.6). The synthesis of well-defined polymers of complex architectures such as multi-functionaUsed block-copolymers is enabled by living polymerisation, one of the main benefits of ROMP [92, 98]. 

The Mizoroki-Heck reaction is a metal catalysed transformation that involves the reaction of a non-functionalised olefin with an aryl or alkenyl group to yield a more substituted aUcene [11,12]. The reaction mechanism is described as a sequence of oxidative addition of the catalytic active species to an aryl halide, coordination of the alkene and migratory insertion, P-hydride elimination, and final reductive elimination of the hydride, facilitated by a base, to regenerate the active species and complete the catalytic cycle (Scheme 6.5). 

The catalytic cycles that have been documented, namely alkyne eyelotrimerization and olefin isomerization, demonstrate that addition and elimination from dimetal centers can occur readily in the presence of metal-metal bonds and alkoxide 1igands. 

The product of the dimerization of an unsymmetrical substituted olefin, such as propene, is dependent on the direction of coupling of the two olefinic units in general, a mixture of isomers is obtained. In order to obtain a high yield of a particular dimer, the control of the regioselectivity of the individual addition steps in the catalytic cycle or even the reversal of the direction of addition in consecutive steps is required (Section IV,E). 

Successive hydrogen transfers within 60, followed by coordination of olefin and then H2 (an unsaturate route), constitute the catalytic cycle, while isomerization is effected through HFe(CO)3(7r-allyl) formed from 59. Loss of H2 from 60 was also considered to be photoinduced, and several hydrides, including neutral and cationic dihydrides of iridium(III) (385, 450, 451), ruthenium(II) (452) and a bis(7j-cyclopentadienyltungsten) dihydride (453), have been shown to undergo such reductive elimination of hydrogen. Photoassisted oxidative addition of H2 has also been dem-... 

Kinetic data were interpreted in terms of a mechanism in which initial heterolytic cleavage of H2 involved the basic 0 ligand coordination of olefin at the generated free equatorial site, followed by insertion to give alkyl and then protonation of the Pd-alkyl bond by the phenolic OH group, completes the catalytic cycle ... 

The catalytic cycle proposed for the cyclization-hydrosilylation with the cationic palladium catalyst is classified into the type D in Scheme 2. The reaction consists of an olefin insertion into palladium-silicon bond and the metathesis between palladium-carbon and hydrogen-silicon bond, regenerating the silylpalladium intermediate and releasing the product where migratory insertion of the pendant olefin into the alkylpalladium is involved before the metathesis (Scheme 26).83a... 

Shortly after the key mechanistic papers on rhodium-catalyzed hydroboration, Marks reported a hydroboration reaction catalyzed by lanthanide complexes that proceeds by a completely different mechanism.63 Simple lanthanide salts such as Sml3 were also shown to catalyze the hydroboration of a range of olefins.64 The mechanism for this reaction was found to be complex and unknown. As in other reactions catalyzed by lanthanides, it is proposed that the entire catalytic cycle takes place without any changes in oxidation state on the central metal. 

First, solvent molecules, referred to as S in the catalyst precursor, are displaced by the olefinic substrate to form a chelated Rh complex in which the olefinic bond and the amide carbonyl oxygen interact with the Rh(I) center (rate constant k ). Hydrogen then oxidatively adds to the metal, forming the Rh(III) dihydride intermediate (rate constant kj). This is the rate-limiting step under normal conditions. One hydride on the metal is then transferred to the coordinated olefinic bond to form a five-membered chelated alkyl-Rh(III) intermediate (rate constant k3). Finally, reductive elimination of the product from the complex (rate constant k4) completes the catalytic cycle. 

---