Nylon melt

Nylon Melting Point (°C) Nylon Melting Point (°C)... 

Other perfluoroalkyl polymers have been produced with sufficient thermal stability to withstand the temperatures of nylon melts from which carpet fihers are spun. During the subsequent heat treatment of the fiher the perfluoroalkyl groups diffuse to the surface to form a soil-resistant coating. Although such coatings add to the initial cost of the carpet they eventually save money by increasing the time intervals between cleanings. 

NYLON Melts no flame Like celery Melts to black beod, hard to crush... 

Nylon Melts and burns with Burning Hard, round. 

Mallon, F.K Ray, W.H. A comprehensive model for nylon melt equihbria and kinetics, J. Appl... 

Polyamides (nylons) melt and drip on ignition so that when held horizontally they tend to be selfextinguishing. However, the molten drips can continue to bum. Grades reinforeed with glass or minerals tend to have inereased burning rates. 

Pisipati, R. and Baird, D.G. (1981) Correlation of rheological properties of filled nylon melts with processing performance, SPE ANTEC, 27,32-4. 

Figure 4.40 (a) Velocity and (b) temperature profiles for the spinning of industrial nylon melts at... 

Nylon melts, bubbles and chars slightly before it burns with molten drops falling. The smell is like burning hair or wool. 

Add 40 ml. of ethyl alcohol to 21 -5 g. of 70 per cent, ethylenediamine solution (0 -25 mol) dissolve 36 -5 g. of adipic acid (0 -25 mol) in 50 ml. of a 6 1 mixture of ethyl alcohol and water. Mix the two solutions, stir and cool. Filter off the resulting salt and recrystalliae it from 60 ml. of a 6 1 ethyl alcohol - water mixture, and dry the salt in the air. Heat the salt in an atmosphere of oxygen-free nitrogen or of carbon dioxide in an oil bath until it melts (ca. 160°) the product will sohdify after a short time. Reduce the pressure to 15 mm. of mercury or less and raise the temperature of the oil bath until the product remelts (about 290°) and continue the heating for 4r-5 hours. Upon coohng, a nylon type polymer is obtained. 

Nylon 6 and 6/6 possess the maximum stiffness, strength, and heat resistance of all the types of nylon. Type 6/6 has a higher melt temperature, whereas type 6 has a higher impact resistance and better processibility. At a sacrifice in stiffness and heat resistance, the higher analogs of nylon are useful primarily for improved chemical resistance in certain environments (acids, bases, and zinc chloride solutions) and for lower moisture absorption. 

Other elastomeric-type fibers iaclude the biconstituents, which usually combine a polyamide or polyester with a segmented polyurethane-based fiber. These two constituents ate melt-extmded simultaneously through the same spinneret hole and may be arranged either side by side or ia an eccentric sheath—cote configuration. As these fibers ate drawn, a differential shrinkage of the two components develops to produce a hehcal fiber configuration with elastic properties. An appHed tensile force pulls out the helix and is resisted by the elastomeric component. Kanebo Ltd. has iatroduced a nylon—spandex sheath—cote biconstituent fiber for hosiery with the trade name Sidetia (6). 

However, because of the low melting poiats and poor hydrolytic stabiUty of polyesters from available iatermediates, Carothers shifted his attention to linear ahphatic polyamides and created nylon as the first commercial synthetic fiber. It was nearly 10 years before. R. Whinfield and J. T. Dickson were to discover the merits of poly(ethylene terephthalate) [25038-59-9] (PET) made from aromatic terephthaUc acid [100-21-0] (TA) and ethylene glycol [107-21-1] (2G). 

Thermoplastic Fibers. The thermoplastic fibers, eg, polyester and nylon, are considered less flammable than natural fibers. They possess a relatively low melting point furthermore, the melt drips rather than remaining to propagate the flame when the source of ignition is removed. Most common synthetic fibers have low melting points. Reported values for polyester and nylon are 255—290°C and 210—260°C, respectively. 

Regulatory Legislation. In Febmary 1978, the Consumer Products Safety Commission approved changes in the FF-3 and FF-5 standards for children s sleepwear. It eliminated the melt—drip time limit and coverage for sizes below 1 and revised the method of testing the trim. This permits the use of untreated 100% nylon and 100% polyester for children s sleepwear (157—162). 

Many polymers, including polyethylene, polypropylene, and nylons, do not dissolve in suitable casting solvents. In the laboratory, membranes can be made from such polymers by melt pressing, in which the polymer is sandwiched at high pressure between two heated plates. A pressure of 13.8—34.5 MPa (2000—5000 psi) is appHed for 0.5 to 5 minutes, at a plate temperature just above the melting point of the polymer. Melt forming is commonly used to make dense films for packaging appHcations, either by extmsion as a sheet from a die or as blown film. 

The packaging (qv) requirements for shipping and storage of thermoplastic resins depend on the moisture that can be absorbed by the resin and its effect when the material is heated to processing temperatures. Excess moisture may result in undesirable degradation during melt processing and inferior properties. Condensation polymers such as nylons and polyesters need to be specially predried to very low moisture levels (3,4), ie, less than 0.2% for nylon-6,6 and as low as 0.005% for poly(ethylene terephthalate) which hydrolyzes faster. 

Polyamides, often also lefeiied to as nylons, are liigli polymers which contain the amide repeat linkage in the polymer backbone. They are generally characterized as tough, translucent, semicrystalline polymers that ate moderately low cost and easily manipulated commercially by melt processing. 

---