Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Nozzle impact

Nebulizers can be divided into several main types. The pneumatic forms work on the principle of breaking up a stream of liquid into droplets by mechanical means the liquid stream is forced through a fine nozzle and breaks up into droplets. There may be a concentric stream of gas to aid the formation of small droplets. The liquid stream can be directed from a fine nozzle at a solid target so that, on impact, the narrow diameter stream of liquid is broken into many tiny droplets. There are variants on this approach, described in the chapter devoted to nebulizers (Chapter 19). [Pg.106]

Fig. 4. (a) Type-S pitot tube and thermocouple (b) side view of the correct pitot tube configuration when used ia conjunction with a sampling nozzle, where A is the static pressure opening plane and B is the impact pressure opening plane and (c) bottom view. [Pg.300]

In calculating the impact point of spray, one should recognize that the spray angle closes in as the spray moves away from the nozzle. This is caused by loss of momentum of the spray to the gas. [Pg.1412]

The second, additive term carrying the viscosity impact in Eq. (14-199) is small at viscosities around 1 centipoise but can become controlling as viscosity increases. For example, for air at atmospheric pressure atomizing water, with nozzle conditions. [Pg.1412]

Goldberg and Rubin [Ind. Eng. Chem. Proce.s.s Des. Dev., 6 195 (1967)] showed in tests with a disk spinning vertically to the foam layer that most mechanical procedures, whether centrifugation, mixing, or blowing through nozzles, consist basically of the application of shear stress. Subjecting foam to an air-jet impact can also provide a source... [Pg.1443]

Deterioration of tubes near the inlet nozzle of condenser shells due to impingement of water and steam mixtures can be alleviated through the use of appropriately placed and sized baffles or impact plates or by applying clip-on impingement shields to the tubes (see Case History 11.3). [Pg.249]

Nozzle arrangements for various applications vary considerably. For subcritical flow measurement at the outlet end, where nozzle differential pressure p is less than the barometric pressure, flow should be measured with impact tubes and manometers as shown in Figure 20-3. [Pg.699]

Gases or vapours that are water soluble or miscible or that are only soluble or highly reactive in other agents Absorption with multiple surface contact by atomizing liquid with spray nozzle or jet impaction Crabtree ozone analyser or midget venturi scrubber Water, acid, or alkali 5-25 60-100 Venturi scrubber satisfactory if dust is present Atomizer absorber will plug... [Pg.320]

The shuttle shifter moves the plates back one by one towards the fixed header. When each plate parks the cloth is washed at 100 bar with a mechanism that lowers and lifts a pair of symmetrical manifolds with high impact nozzles. [Pg.191]

The two manifolds that wash the cloth on both sides of the plate have high impact nozzles at a pressure of 100 bar. When some nozzles of one manifold are plugged the jet impact is uneven and the plates tend to swing. [Pg.191]

O When the cake tends to clog the cloth its continuous removal after cake discharge enables dislodging of particles by thorough washing of the cloth on both sides with high impact nozzles. [Pg.211]

The twisting rubber hoses or o ringed elbows which connect the rotating pan necks with pipe and the wear plate to the face of the stationary valve The condition of the high impact nozzles mounted on the cloth wash manifold and, for wet cake discharge, the sluicing manifold The support rollers which take the vertical load of the entire machine and the horizontal thrust rolls that maintain the rotating frame concentric The toothed rim and sprocket which drives the pan filter... [Pg.230]

A general appreciation of some of the effect of gas pulsation on the performance and impact on the compressor pulsation drums, their nozzles, the piping system, and the cylinder valve performance, as well as possible other effects in some unique systems or items of equipment, can be discovered by examining the cylinder performance using an indicator card. This examination (see Chapter 12) can reveal acceptable and unacceptable performance in terms of pressure variations within the cylinder as the piston passes through its cycle. Hicks presents a helpful analysis see Figures 13-3 and 13M. [Pg.582]

Optimal hydraulics is the proper balance of hydraulic parameters (flowrate and equivalent nozzle size) that satisfy chosen criteria of optimization. Hydraulic quantities used to characterize jet bit performance include hydraulic horsepower, jet impact force, jet velocity, Reynolds number at the nozzle, generalized drilling rate or cost per foot drilled. While designing the hydraulic program the limitations due to cuttings transport in the annulus and pump performance characteristics must be included. [Pg.1097]

Absorption with multiple surface contact by atomizing liquid with spray nozzle or jet impaction... [Pg.209]

When ammonia is injected, NH2, NH, N, and H radicals are formed in the region close to the nozzles by the following electron impact dissociation reactions [59,60] ... [Pg.374]


See other pages where Nozzle impact is mentioned: [Pg.787]    [Pg.787]    [Pg.403]    [Pg.7]    [Pg.145]    [Pg.90]    [Pg.285]    [Pg.242]    [Pg.2389]    [Pg.15]    [Pg.700]    [Pg.158]    [Pg.591]    [Pg.19]    [Pg.190]    [Pg.864]    [Pg.1183]    [Pg.492]    [Pg.494]    [Pg.182]    [Pg.373]    [Pg.455]    [Pg.31]    [Pg.2]    [Pg.27]    [Pg.28]    [Pg.48]    [Pg.397]    [Pg.363]    [Pg.50]    [Pg.59]    [Pg.60]    [Pg.81]    [Pg.83]   
See also in sourсe #XX -- [ Pg.183 ]




SEARCH



Nozzle

Nozzle, nozzles

© 2024 chempedia.info