Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Screw nails

Materials The cost of items purchased for use in the project. Includes such things as lumber, cement, steel, nails, screws, rivets, bolts, and paint. [Pg.826]

The use of PVC wood, which includes PVC foam and PVC/wood flour composite, as an alternative to wood and wood-like products is discussed. Compared with traditional products, the PVC wood is shown to exhibit improved termite resistance and weathering resistance, lower moisture absorption and ease of installation. It is demonstrated that PVC wood can be nailed, screwed, sawed, cut and bonded like wood by conventional tools without any special skills being required. The bending strength of PVC wood is lower, but it can still be used for... [Pg.87]

Using nails, screws or glue, assemble the box. There will be no top to it. [Pg.37]

Polyethylene is rather soft, making PE-based composite deck boards easier to nail, screw, cut, and saw. Polyethylene, as well as polypropylene, shows near-zero moisture absorption (typically below 0.02% after 24 h underwater immersion) and... [Pg.51]

Wire - available in sizes up to 10 mm diameter, wire is used in the production of rivets, nails, screws, bolts and welding rods, in metal spraying, and for electrical cables. [Pg.223]

Adhesives have many advantages over other joining materials such as nails, screws, threads, etc. They permit a greater stress distribution over a wider area, act as moisture barrier or electrostatic insulators, allow very thin sections to be joined, can be worked quicker and, in addition, often cost less. [Pg.789]

With up to 70% of the WPC being cellulose material, the materials behave like wood and can be turned, drilled, sanded, sawed, mitred, routed, tenoned and planed like wood using conventional woodworking tools. WPC products can also be used with fasteners such as nails, screws and staples and can hold fasteners up to two to four times better than wood. This permits further design freedom since smaller fasteners may be used to achieve equal hold. Special adhesives can be used to provide excellent adhesion on all types of joints. During installation, silicone or acrylic seals and wood fillers can be used successfully. [Pg.364]

Each of these composite wood product types can be manufactured in a variety ways, comprising different physical or chemical attributes that may affect composting procedures and end-product applications. Furthermore, the prior use of these wood products will determine the presence or absence of such components as fasteners, nails, screws, bolts, plastic coatings and paint. It is therefore critical for the production of quality compost to be aware of how a wood residual was manufactured, its prior use, and its condition at time of recycling, (e.g., presence of fasteners, paint, etc., and moisture content). [Pg.372]

Dental applicances, fracture plates, heart valves, joint components, nails, screws Conductive leads, joint components, pacemaker cases, nails, screws Fracture plates... [Pg.42]

WOOD. Wet wood has caused varying degrees of corrosion of contacting aluminum aJIoys in labora-tmy tests. The degree of corrosion varied with the type of wood tested. It is good engineering practice to apply protection where aluminum alloys will contact wood which may become wet. Aluminum alloy nails, screws, and bolts have been used in wood. See also Ref (Dp. 147, (3) p. 231. [Pg.629]

Nails, screws, and bolts. Even the most basic home repair tool kit should include a range of nails—ranging from 4d (1 / ") to 16d (3Vi")—and screws. Wood and drywall screws have coarse threads, whereas metal screws have finer threads. Get a range of both. It s also worth having a couple of carriage bolts, eye bolts, and screw eyes on hand. [Pg.216]

Mild steel Sheet strip for presswork, wire and rod for nails, screws, concrete reinforcement bar... [Pg.106]

Dimethylcarbonate (DMC) has found some use as an alkylating agent to produce either methocarbonate quats or bicarbonate quats (after hydrolysis). DMC is a fairly weak alkylating agent and reactions are often run at elevated temperatures with an excess of DMC and methanol as a solvent/catalyst. Other carbonates can be used to make bicarbonate and carbonate quats by an in situ transesterification-quaternization process [35]. The attraction of dimethyl carbonate is that it has a good environmental profile and the quats produced do not have the corrosivity shown by chloride quats, making them favoured for wood preservation where corrosion of nails, screws and staples is a concern. [Pg.29]

The technology of suicide bombings can be quite varied. However, the common perception and indeed the majority of attacks conform to the model of an explosive package worn as a belt or waistcoat, commonly with fragmentation weapons incorporated in the design (often just bags of nails, screws or nuts on the victim-facing side of the weapon). [Pg.94]


See other pages where Screw nails is mentioned: [Pg.1133]    [Pg.188]    [Pg.1166]    [Pg.70]    [Pg.216]    [Pg.219]    [Pg.39]    [Pg.140]    [Pg.1690]    [Pg.140]    [Pg.252]    [Pg.1133]    [Pg.122]    [Pg.81]    [Pg.126]    [Pg.113]    [Pg.285]    [Pg.845]    [Pg.219]    [Pg.93]    [Pg.386]    [Pg.319]    [Pg.142]    [Pg.78]   
See also in sourсe #XX -- [ Pg.285 ]




SEARCH



Nails

© 2024 chempedia.info