Mold engineering

Buckleitner, E. L., et al., Plastics Mold Engineering Handbook, 5th Edition, Kluwer, 1995. 

DuBois JH and Pribble WI (Eds), "Plastic Mold Engineering Handbook, Van Nostrand Reinhold Co, New York, 3rd Ed, 1978. 

DuBois, J. H., and Pribble, W. I., Plastics Mold Engineering, Chicago, American Technical... 

Georgia Gulf. [Georgia Gulf] Vinyl compds. for profile extmsion, molding, engineering applies. 

Uniform thiefcaess is possible to achieve but is rarely the case in fact, in most cases, it is ip ssible. However, Ae designer should make every effort to make Ae thickne in a y area of y product m uniform as possible. Thereasons are quite simple (teisr to Mold Engineering [1] by this auAor) ... 

The product designer who wants more information on venting is referred to Mold Engineering [1], also bv this author. 

Rees, Herbert. Mold Engineering. Munich Hanser Publishers, 1995. 

Opportunities and Risks of Structural Component Design and Mold Engineering. 337... 

The principles that apply to material selection and process engineering, i.e., those of simultaneous engineering, apply most particularly to structural component design and mold engineering. 

In this section as well, examples provide insights into the opportunities and risks involved in structural component design and mold engineering. 

Understanding Injection Mold Design. Hauser, Munich, 2001 Mold Engineering, 2nd ed. Hauser, Munich 2001... 

Plastic Mold Engineering Handbook, 4th ed., edited by J. H. Bubois and W. I. Pribble (Van Nostrand Reinhold, New York, 1987). 

Figures 7.4 and 7.5 show the effects of increasing glass concentration on the tensile moduli and Charpy impact strength values of several injection-molded engineering thermoplastics data on polypropylene, a much lower modulus commodity resin commonly reinforced with glass fibers, are also included for comparison purposes.

Figure S.7 Cross section of a split cavity mold for producing a molded spool. A and B form the two halves of the cavity. Chase, C, folds the halves together. Other parts are D, core pin E bottom plate and F, the force plug or plunger. (Ref Buckleitner, E.V., ed., Basic Mold Types and Features , Plastics Mold Engineering Handbook, S " ed.. Chapman Hall, New YotIc)...

Zhou H, Li DQ (2004) Modeling and prediction of weld line location and properties based on injection molding simulation. Int J Mater Prod Technol 21 526-538 Zhou H, Zhang Y, Wen J, Li DQ (2009) An acceleration method for the BEM-based cooling simulation of injection molding. Engineering Analysis with Boundary Elements 33 1022-1030... 

A review (16) and a book (17) on the chemistry and properties of poly(ether ketones) have been published. PEEK is present in the market also in reinforced grades (glass or carbon fibers) as well as in yams or in powder for coatings. Fibers are marketed by ICI imder the trade name Zyex. PEEK found application in the transport, teletronics, and aerospace sectors, with the fabrication of injection-molded engineering components and circuit boards. PEEK materials have also foimd a place in medical technologies. For this purpose, their biological and toxicological safety has been certified (14). 

These are some of the considerations that the designer must make in the design of a molded part. Plastics Mold Engineering gives a... 

DuBois and Fribble, Plastics Mold Engineering, 3rd Edition, New York, Van Nostrand Rein-hold Co. 1977. 

Plastics Mold Engineering, Written by J.H. DuBois and W.I. Pribble, 5th edition published by Chapman and Hall in 1995. ISBN 0412989514 Library Of Congress 94-17065. It s a large and expensive book with about 700 pages covering all aspects of mold engineering. You might check with the library and see if they have a copy. 

KR 4070 - injection molding (engineering parts with enhanced impact strength, housings and... 

---