Methyl sebacate

C11H20O4 mono-methyl sebacate 818-88-2 21.09 1.0133 2 23240 C12H7CI02 1 -chlorodibenzo-p-dioxin 39227-53-7 25.00 1.3237 2... 

Dimethyl decanedioate Dimethyl octane-1,8-dicarboxylate DMS Methyl sebacate Sebacic acid, dimethyl ester... 

Methyl sebacate 38 288d 216 133,subl 2431s -97 64 65 mono di 201 108 Phenylhydrazide, 194... 

The same extraction technique may be followed by GC on a special, sufficiently rapid, column. A single plasticiser is identified by its retention data with, however, an imcertainty which may be practically eliminated by the use of a chromatogram obtained on a column of different polarity Figure 4.16 shows on the one hand the poor resolution of three plasticisers (a) di-ethyl phthalate, (b) di-methyl sebacate and (c) tributyl phosphate on a non-polar column and on the other hand, the good separation of these substances on a... 

Chlorinated diphenyl Di-methyl sebacate Butyl laurate... 

By increasing the molar proportion of the monocarboxylic acid, the yield of (II) is improved. Thus electrolysis of a mixture of decanoic acid (n-decoic acid capric acid) (V) (2 mols) and methyl hydrogen adipate (VI) (1 mol) in anhydrous methanol in the presence of a little sodium methoxide gives, after hydrolysis of the esters formed, n-octadecane (VII), tetradecanoic or myristic acid (VIH) and sebacic acid (IX) ... 

An excellent synthesis of myristic acid is thus achieved from readily accessible starting materials. An alternative synthesis of myristic acid utilises hexanoic acid (M-caproic acid n-hexoic acid) (X) (2 mols) and methyl hydrogen sebacate (XI) (1 mol) the products, after hydrolysis, are Ji-decane (XII), myristic acid (XIII) and hexadecane-1 16-dlcarboxylic acid (XIV) ... 

Sebacic acid. Dissolve 40 g. of methyl hydrogen adipate in 100 ml. of absolute methanol to which 01 g. of sodium has been added. Pass a current of about 2 0 amps, until the pH of the solution is about 8 (ca. 5 hours) test with B.D.H. narrow-range indicator paper. Transfer the contents of the electrolysis cell to a 500 ml. round-bottomed flask, render neutral with a little acetic acid, and distil off the methanol on a water... 

Myristic acid from hexanoic acid and methyl hydrogen sebacate). Dissolve 23 -2 g. of redistilled hexanoic acid (re caproic acid), b.p. 204-6-205-5°/760 mm., and 21-6 g. of methyl hydrogen sebacate in 200 ml. of absolute methanol to which 0 13 g. of sodium has been added. Electrolyse at 2 0 amps., whilst maintaining the temperature between 30° and 40°, until the pH is about 8 0 (ca. 6 hours). Neutralise the contents of the electrolysis cell with a little acetic acid and distil off the methyl alcohol on a water bath. Dissolve the residue in 200 ml. of ether, wash with three 50 ml. portions of saturated sodium bicarbonate solution, once with water, dry with anhydrous magnesium sulphate, and distil with the aid of a fractionating column (see under Methyl hydrogen adipate). Collect the re-decane at 60°/10 mm. (3 0 g.), the methyl myristate at 158-160°/ 10 mm. (12 5g.) and dimethyl hexadecane-1 16-dicarboxylate at 215-230°/ 7 mm. (1 -5 g.)... 

Alkali Fusion. Tha alkaU fusion of castor oil using sodium or potassium hydroxide in the presence of catalysts to spHt the ricinoleate molecule, results in two different products depending on reaction conditions (37,38). At lower (180—200°C) reaction temperatures using one mole of alkah, methylhexyl ketone and 10-hydroxydecanoic acid are prepared. The 10-hydroxydecanoic acid is formed in good yield when either castor oil or methyl ricinoleate [141-24-2] is fused in the presence of a high boiling unhindered primary or secondary alcohol such as 1- or 2-octanol. An increase to two moles of alkali/mole ricinoleate and a temperature of 250—275°C produces capryl alcohol [123-96-6] CgH gO, and sebacic acid [111-20-6] C QH gO, (39—41). Sebacic acid is used in the manufacture of nylon-6,10. 

Another alternative method to produce sebacic acid iavolves a four-step process. First, butadiene [106-99-0] is oxycarbonylated to methyl pentadienoate which is then dimerized, usiag a palladium catalyst, to give a triply unsaturated dimethyl sebacate iatermediate. This unsaturated iatermediate is hydrogenated to dimethyl sebacate which can be hydrolyzed to sebacic acid. Small amounts of branched chain isomers are removed through solvent crystallizations giving sebacic acid purities of greater than 98% (66). 

Of interest is the manner in which cavities of the appropriate size are introduced into ion-selective membranes. These membranes typically consist of highly plasticized poly(vinyl chloride) (see Membrane technology). Plasticizers (qv) are organic solvents such as phthalates, sebacates, trimelLitates, and organic phosphates of various kinds, and cavities may simply be the excluded volumes maintained by these solvent molecules themselves. More often, however, neutral carrier molecules (20) are added to the membrane. These molecules are shaped like donuts and have holes that have the same sizes as the ions of interest, eg, valinomycin [2001-95-8] C H QN O g, and nonactin [6833-84-7] have wrap around stmctures like methyl monensin... 

Sebacoin has been prepared only by cyclization of methyl or ethyl sebacate with sodimn metal. ... 

---