Methyl methacrylate structure

Brown, D., Natansohn, A., Rochon, P. (1995). Azo polymers for reversible optical storage 5. Orientation and dipolar interactions of azobenzene side groups in copolymers and blends containing methyl methacrylate structural units. Macromolecules 28, 6116-6123. 

It is not the purpose of this book to discuss in detail the contributions of NMR spectroscopy to the determination of molecular structure. This is a specialized field in itself and a great deal has been written on the subject. In this section we shall consider only the application of NMR to the elucidation of stereoregularity in polymers. Numerous other applications of this powerful technique have also been made in polymer chemistry, including the study of positional and geometrical isomerism (Sec. 1.6), copolymers (Sec. 7.7), and helix-coil transitions (Sec. 1.11). We shall also make no attempt to compare the NMR spectra of various different polymers instead, we shall examine only the NMR spectra of different poly (methyl methacrylate) preparations to illustrate the capabilities of the method, using the first system that was investigated by this technique as the example. 

Figure 7.10 shows the 60-MHz spectra of poly (methyl methacrylate) prepared with different catalysts so that predominately isotactic, syndiotactic, and atactic products are formed. The three spectra in Fig. 7.10 are identified in terms of this predominant character. It is apparent that the spectra are quite different, especially in the range of 5 values between about 1 and 2 ppm. Since the atactic polymer has the least regular structure, we concentrate on the other two to make the assignment of the spectral features to the various protons. 

The hydrogens of the methylene group in the backbone of the poly (methyl methacrylate) produce a single peak in a racemic dyad, as illustrated by structure [XVI]. 

Poly(methyl methacrylate) (Figure 15.1, I) is, commercially, the most important member of a range of acrylic polymers which may be considered structurally as derivatives of acrylic acid (II). 

Commercial poly(methyl methacrylate) is a transparent material, and microscopic and X-ray analyses generally indicate that the material is amorphous. For this reason the polymer was for many years considered to be what is now known as atactic in structure. It is now, however, known that the commercial material is more syndiotactic than atactic. (On one scale of assessment it might be considered about 54% syndiotactic, 37% atactic and 9% isotactic. Reduction in the temperature of free-radical polymerisation down to -78°C increases the amount of syndiotacticity to about 78%). 

Monodispersed poly (methyl methacrylate-ethyleneglycol dimethacrylate) is prepared by a multistep swelling and polymerization method. When a good solvent such as toluene is applied as a porogen, the seed polymer severely affects the pore structure, whereas no effects are observed with poor solvents, such as cyclohexanol, as a porogen, in comparison with the conventional suspension polymerization (68,69). 

Kondo maintained his interest in this area, and with his collaborators [62] he recently made detailed investigations on the polymerization and preparation of methyl-4-vinylphenyl-sulfonium bis-(methoxycarbonyl) meth-ylide (Scheme 27) as a new kind of stable vinyl monomer containing the sulfonium ylide structure. It was prepared by heating a solution of 4-methylthiostyrene, dimethyl-diazomalonate, and /-butyl catechol in chlorobenzene at 90°C for 10 h in the presence of anhydride cupric sulfate, and Scheme 27 was polymerized by using a, a -azobisi-sobutyronitrile (AIBN) as the initiator and dimethylsulf-oxide as the solvent at 60°C. The structure of the polymer was confirmed by IR and NMR spectra and elemental analysis. In addition, this monomeric ylide was copolymerized with vinyl monomers such as methyl methacrylate (MMA) and styrene. 

Amorphous thermoplastics These are made from polymers which have a sufficiently irregular molecular structure to prevent them from crystallising in any way. Examples of such materials are polystyrene, poly methyl methacrylate and polyvinyl chloride. 

IUPAC recommendations suggest that a copolymer structure, in this case poly(methyl methacrylate-co-styrene) or copoly(methyl methacrylate/slyrene), should be represented as 1. The most substituted carbon of the configurational repeat unit should appear first. This same rule would apply to the copolymer segments shown in Section 7.1. However, as was mentioned in Chapter I, in this book, because of the focus on mechanism, we have adopted the more traditional depiction 2 which follows more readily from the polymerization mechanism. 

O.P. Korobeinichev et al, Structure of the Extinguished Surface of a Catalyzed Ammonium Perchlorate-Poly(Methyl Methacrylate) Mixture , FizzGoreniyaVzryva 10 (3), 345-53 (1974)... 

Waters61 have measured relative rates of p-toluenesulfonyl radical addition to substituted styrenes, deducing from the value of p + = — 0.50 in the Hammett plot that the sulfonyl radical has an electrophilic character (equation 21). Further indications that sulfonyl radicals are strongly electrophilic have been obtained by Takahara and coworkers62, who measured relative reactivities for the addition reactions of benzenesulfonyl radicals to various vinyl monomers and plotted rate constants versus Hammett s Alfrey-Price s e values these relative rates are spread over a wide range, for example, acrylonitrile (0.006), methyl methacrylate (0.08), styrene (1.00) and a-methylstyrene (3.21). The relative rates for the addition reaction of p-methylstyrene to styrene towards methane- and p-substituted benzenesulfonyl radicals are almost the same in accord with their type structure discussed earlier in this chapter. 

Using these macroinitiators PDMS-polystyrene and PDMS-poly(methyl methacrylate) multiblock copolymers were synthesized 305). Due to the backbone Structure of these macroinitiators and their thermolysis mechanisms, the copolymers obtained... 

Siloxane containing interpenetrating networks (IPN) have also been synthesized and some properties were reported 59,354 356>. However, they have not received much attention. Preparation and characterization of IPNs based on PDMS-polystyrene 354), PDMS-poly(methyl methacrylate) 354), polysiloxane-epoxy systems 355) and PDMS-polyurethane 356) were described. These materials all displayed two-phase morphologies, but only minor improvements were obtained over the physical and mechanical properties of the parent materials. This may be due to the difficulties encountered in controlling the structure and morphology of these IPN systems. Siloxane modified polyamide, polyester, polyolefin and various polyurethane based IPN materials are commercially available 59). Incorporation of siloxanes into these systems was reported to increase the hydrolytic stability, surface release, electrical properties of the base polymers and also to reduce the surface wear and friction due to the lubricating action of PDMS chains 59). 

This paper presents the physical mechanism and the structure of a comprehensive dynamic Emulsion Polymerization Model (EPM). EPM combines the theory of coagulative nucleation of homogeneously nucleated precursors with detailed species material and energy balances to calculate the time evolution of the concentration, size, and colloidal characteristics of latex particles, the monomer conversions, the copolymer composition, and molecular weight in an emulsion system. The capabilities of EPM are demonstrated by comparisons of its predictions with experimental data from the literature covering styrene and styrene/methyl methacrylate polymerizations. EPM can successfully simulate continuous and batch reactors over a wide range of initiator and added surfactant concentrations. 

As the majority of stabilisers has the structure of aromatics, which are UV-active and show a distinct UV spectrum, UV spectrophotometry is a very efficient analytical method for qualitative and quantitative analysis of stabilisers and similar substances in polymers. For UV absorbers, UV detection (before and after chromatographic separation) is an appropriate analytical tool. Haslam et al. [30] have used UV spectroscopy for the quantitative determination of UVAs (methyl salicylate, phenyl salicylate, DHB, stilbene and resorcinol monobenzoate) and plasticisers (DBP) in PMMA and methyl methacrylate-ethyl acrylate copolymers. From the intensity ratio... 

Ethylene vinyl acetate has also found major applications in drug delivery. These copolymers used in drug release normally contain 30-50 wt% of vinyl acetate. They have been commercialized by the Alza Corporation for the delivery of pilocarpine over a one-week period (Ocusert) and the delivery of progesterone for over one year in the form of an intrauterine device (Progestasert). Ethylene vinyl acetate has also been evaluated for the release of macromolecules such as proteins. The release of proteins form these polymers is by a porous diffusion and the pore structure can be used to control the rate of release (3). Similar nonbiodegradable polymers such as the polyurethanes, polyethylenes, polytetrafluoroethylene and poly(methyl methacrylate) have also been used to deliver a variety of different pharmaceutical agents usually as implants or removal devices. 

Iso tactic poly(methyl methacrylate) (it-PMMA) can form a stereocomplex with st-PMMA. Recent X-ray studies 179) of this material indicate that the two polymer chains probably interact to form a double helical structure. The it-PMMA chain forms the inner helix and is surrounded by the st-PMMA helical chain which winds around it. If subsequent work confirms this model, this material would constitute a most unusual inclusion compound involving only one monomeric substance. 

---