Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Media impact

FIGURE 4M Flviid-particle interaction at grinding media impact. [Pg.104]

Type of release Size of release Major media impacted Description of category... [Pg.85]

The third area of media impact is in presenting norms media attempt to reflect our arts and social customs. There is no question that media homogenize culture in a regretable way. There are those who devote their lives to improving this content and form dilemma. [Pg.154]

Publicity (Mass Media impact) Local media and scare repercussions abroad the country Global... [Pg.99]

Affected Environmental Media Presence of soil, groundwater, or other environmental media impacted by release. Conduct site inspection or fleld/laboratory measurements. [Pg.228]

Facihties located in non-attainment areas or that are increasing emissions in such areas must apply for a state permit prior to starting construction. The permit must codify that they are applying Lowest Achievable Emissions Rate (LAER). LAER is also estabhshed on a case by case basis. They also need to obtain equivalent offsetting emissions reductions (Offsets) from existing soxuces within the non-attainment area. Unlike BACT, a LAER determination does not consider economic, energy, or other cross-media impacts. [Pg.1286]

For a smaller size 0 mill with a diameter of 5-7/8" (.49 foot) the critical speed is 109 rpm. Most laboratory jar rollers either have variable speed controls or are preset to fall in the 35 to 115% range. Most of our dispersion milling takes place at 50 to 80 rpm. From a practical "hands-on perspective, if the mill is rolling at a correct speed, the sound of media impact against the jar should be audible. [Pg.71]

Properties ASTM Method High impact Medium impact Heat resistant... [Pg.202]

Property Units G.P. polystyrene Medium-impact PS-SBR blend Very high impact PS-SBR blend Styrene acrylonitrile Medium impact ABS High impact ABS MBS... [Pg.445]

Unit Ratio Material Balance for Medium Impact Polystyrene (MIPS)... [Pg.99]

The medium impact-sensitivity of this solid propellant component is greatly increased by co-crystallisation of certain impurities, notably nitryl perchlorate, potassium periodate and potassium permanganate [1]. The presence of certain minimum amounts of mono-, di, tri- or tetra-methylammonium perchlorates in the salt leads to a single step decomposition, at around 290°C for the monoderivative [2],... [Pg.1367]

Ammonium hexanitrocobaltate(3—) [14652-46-1] [NH4]3[Co(N02)6] Explodes at 230°C, medium impact-sensitivity. See entry amminemetal oxosalts (reference 2) CoH12N9012... [Pg.1472]

Suitable Plastics Acrylics, polystyrenes, cellulose acetates, cellulose buy rates, ionomers, rigid vinyls, polycarbonates, and medium-impact styrenes. [Pg.122]

Property Summary Acrylics recommended for general-purpose applications, especially for optical decorative, and outdoor use. In sheet stock, cast acrylic has greater strength and transparency extruded acrylic costs less (especially in thin members), and has better formability. Polycarbonates for maximum strength, as in explosion shields. Butyrates for excellent impact resistance, and deep formability. Vinyls for maximum formability and printability. Acetates and vinyls for flexible glazing and guards. Medium-impact styrene and rigid vinyls for lowest-cost molded transparent parts. [Pg.124]

Explodes at 325°C medium impact-sensitivity. See entry AMMINEMETAL OXOSALTS (reference 3)... [Pg.229]

Since these rubber particles are highly filled with a homopolymer or a copolymer, the rubber is already reinforced with a resin to give a higher modulus particle than the grafted rubber latex. On the basis of the uniqueness of these rubber particles, this process is also more appropriate in manufacturing high-strength medium-impact ABS polymer (31), or rubber-reinforced styrene-methyl methacrylate copolymer (32). The... [Pg.99]


See other pages where Media impact is mentioned: [Pg.110]    [Pg.154]    [Pg.155]    [Pg.35]    [Pg.418]    [Pg.409]    [Pg.543]    [Pg.331]    [Pg.652]    [Pg.72]    [Pg.75]    [Pg.129]    [Pg.228]    [Pg.324]    [Pg.206]    [Pg.361]    [Pg.853]    [Pg.853]    [Pg.1471]    [Pg.559]    [Pg.877]    [Pg.402]    [Pg.122]    [Pg.331]    [Pg.543]    [Pg.402]    [Pg.924]    [Pg.924]    [Pg.199]    [Pg.354]    [Pg.853]    [Pg.853]    [Pg.1471]    [Pg.36]    [Pg.171]    [Pg.172]   
See also in sourсe #XX -- [ Pg.963 , Pg.964 ]




SEARCH



Impact Factors of Polymer Rheology in Porous Media

Medium impact polystyrene

Medium impact polystyrene MIPS)

© 2024 chempedia.info