Mechanisms sulfone

Nitration in the 3-position with N205 and a sulfur nucleophile Scope, limitations and mechanism Sulfonation of Pyridines... 

Lithiation at C2 can also be the starting point for 2-arylatioii or vinylation. The lithiated indoles can be converted to stannanes or zinc reagents which can undergo Pd-catalysed coupling with aryl, vinyl, benzyl and allyl halides or sulfonates. The mechanism of the coupling reaction involves formation of a disubstituted palladium intermediate by a combination of ligand exchange and oxidative addition. Phosphine catalysts and salts are often important reaction components. 

When unsubstituted, C-5 reacts with electrophilic reagents. Thus phosphorus pentachloride chlorinates the ring (36, 235). A hydroxy group in the 2-position activates the ring towards this reaction. 4-Methylthiazole does not react with bromine in chloroform (201, 236), whereas under the same conditions the 2-hydroxy analog reacts (55. 237-239. 557). Activation of C-5 works also for sulfonation (201. 236), nitration (201. 236. 237), Friede 1-Crafts reactions (201, 236, 237, 240-242), and acylation (243). However, iodination fails (201. 236). and the Gatterman or Reimer-Tieman reactions yield only small amounts of 4-methyl-5-carboxy-A-4-thiazoline-2-one. Recent kinetic investigations show that 2-thiazolones are nitrated via a free base mechanism. A 2-oxo substituent increases the rate of nitration at the 5-position by a factor of 9 log... 

The mechanisms by which sulfonate esters undergo nucleophilic substitution are the same as those of alkyl halides Inversion of configuration is observed m 8 2 reac tions of alkyl sulfonates and predominant inversion accompanied by racemization m 8 1 processes... 

Among the variety of electrophilic species present m concentrated sulfuric acid sulfur tnoxide (Figure 12 4) is probably the actual electrophile m aromatic sulfonation We can represent the mechanism of sulfonation of benzene by sulfur tnoxide by the sequence of steps shown m Figure 12 5... 

Complexation of bromine with iron(III) bromide makes bromine more elec trophilic and it attacks benzene to give a cyclohexadienyl intermediate as shown m step 1 of the mechanism (Figure 12 6) In step 2 as m nitration and sulfonation loss of a proton from the cyclohexadienyl cation is rapid and gives the product of electrophilic aromatic substitution... 

Write a stepwise mechanism for the conversion of p-toluene sulfonic acid to p-cresol under the conditions shown in the preceding equation... 

Fig. 21. Representative nonionic photoacid generators. A variety of photochemical mechanisms for acid production ate represented. In each case a sulfonic acid derivative is produced (25,56,58—60). (a) PAG that generates acid via 0-nitrobenzyl rearrangement (b) PAG that generates acid via electron transfer with phenohc matrix (c) PAG that is active at long wavelengths via electron-transfer sensitization (d) PAG that generates both carboxylic acid and...

Soluble Salt Flotation. KCl separation from NaCl and media containing other soluble salts such as MgCl (eg, The Dead Sea works in Israel and Jordan) or insoluble materials such as clays is accompHshed by the flotation of crystals using amines as coUectors. The mechanism of adsorption of amines on soluble salts such as KCl has been shown to be due to the matching of coUector ion size and lattice vacancies (in KCl flotation) as well as surface charges carried by the soflds floated (22). Although cation-type coUectors (eg, amines) are commonly used, the utUity of sulfonates and carboxylates has also been demonstrated in laboratory experiments. 

Some amorphous copoly(ether—sulfone) fkms have been prepared (117) with Ts around 130°C with no loss in weight up to 400°C in ak or N2. Other backbones iavestigated in this class of polymers are copoly(ether—amides) (118) and copoly(ether—ketones) (119). These polymers show good mechanical properties, flow characteristics, and abrasion resistance. 

Delignification Chemistty. The chemical mechanism of sulfite delignification is not fully understood. However, the chemistry of model compounds has been studied extensively, and attempts have been made to correlate the results with observations on the rates and conditions of delignification (61). The initial reaction is sulfonation of the aUphatic side chain, which occurs almost exclusively at the a-carbon by a nucleophilic substitution. The substitution displaces either a hydroxy or alkoxy group ... 

The mechanism for sulfonation of hydrogenated fatty esters is accepted as a two-stage process. A rapid sequence of reactions leads to the formation of intermediates having approximately 2 1 stoichiometry of sulfur trioxide to ester. In the subsequent slower and higher temperature aging step, the SO is released for further reactions and the starting material conversion proceeds to completion (133). 

The Albright Wilson continuous SO loop sulfonation system claims use of a static mixer or mechanical mixer system under conditions of... 

Modification of the membranes affects the properties. Cross-linking improves mechanical properties and chemical resistivity. Fixed-charge membranes are formed by incorporating polyelectrolytes into polymer solution and cross-linking after the membrane is precipitated (6), or by substituting ionic species onto the polymer chain (eg, sulfonation). Polymer grafting alters surface properties (7). Enzymes are added to react with permeable species (8—11) and reduce fouling (12,13). 

The azo coupling reaction proceeds by the electrophilic aromatic substitution mechanism. In the case of 4-chlorobenzenediazonium compound with l-naphthol-4-sulfonic acid [84-87-7] the reaction is not base-catalyzed, but that with l-naphthol-3-sulfonic acid and 2-naphthol-8-sulfonic acid [92-40-0] is moderately and strongly base-catalyzed, respectively. The different rates of reaction agree with kinetic studies of hydrogen isotope effects in coupling components. The magnitude of the isotope effect increases with increased steric hindrance at the coupler reaction site. The addition of bases, even if pH is not changed, can affect the reaction rate. In polar aprotic media, reaction rate is different with alkyl-ammonium ions. Cationic, anionic, and nonionic surfactants can also influence the reaction rate (27). 

The main by-products of the Ullmaim condensation are l-aniinoanthraquinone-2-sulfonic acid and l-amino-4-hydroxyanthraquinone-2-sulfonic acid. The choice of copper catalyst affects the selectivity of these by-products. Generally, metal copper powder or copper(I) salt catalyst has a greater reactivity than copper(Il) salts. However, they are likely to yield the reduced product (l-aniinoanthraquinone-2-sulfonic acid). The reaction mechanism has not been estabUshed. It is very difficult to clarify which oxidation state of copper functions as catalyst, since this reaction involves fast redox equiUbria where anthraquinone derivatives and copper compounds are concerned. Some evidence indicates that the catalyst is probably a copper(I) compound (28,29). 

Early recommendations for cross-linking CSM involved the use of divalent metal oxides to form metal sulfonate cross-links (24). The mechanism involves the hydrolysis of the sulfonyl chloride group with a carboxyHc acid, ie, stearic acid, which produces water at curing temperatures. 

---