Measurement of fluid flow

Measurement of Fluid Flow hy Means of Orifice Plates, Nobles and Venturi Tubes Inserted in Circular Cross Section Conduits Punning Full, ISO 5167-1980(e), International Organization for Standardization, Geneva, Switzerland, 1980. [Pg.68]

There are do2ens of flow meters available for the measurement of fluid flow (30). The primary measurements used to determine flow include differential pressure, variable area, Hquid level, electromagnetic effects, thermal effects, and light scattering. Most of the devices discussed herein are those used commonly in the process industries a few for the measurement of turbulence are also described. [Pg.109]

ISO 3966. Measurements of fluid flow in closed conduits—Velocity area method using Pitot static tube. 1977, p. 39. [Pg.1023]

ISO Standard 3966. Measurement of Fluid Flow in Closed Conduits—Velocity Area Method Using Pitot Static Tubes. International Organisation fot Standardisation, 1977. [Pg.1175]

ISO 5167-1 1991. Measurement of Fluid Flow by Means of Pressure Differential Devices-Fart 1 Orifice Plates, Nozzles and Venturi Tubes Inserted in Circular Cross-section Conduits Running Full. International Organisation for Standardisation, 1991. [Pg.1175]

ISO/TR 5168 1998. Measurement of Fluid Flow—Evaluation of Uncertainties. International Organi-sation fot Standardisation, 1998. [Pg.1175]

Hot wire microphone anemometer An instrument for the measurement of fluid flow. [Pg.1448]

Measurement of fluid flow by means of orifice plates, nozzles etc. 1980... [Pg.180]

BS EN ISO 5167-1. .. -4, Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full, BSI. [Pg.95]

Rahman, M.M. and Gui, F., Experimental Measurements of Fluid Flow and Heat Transfer in MicroChannel Cooling Passages in A Chip Substrate, Advances in Electronic Packaging, ASME EEP-4-2, 1993, 685-692. [Pg.23]

Mead K, Koehl MAR (2000) Particle image velocimetry measurements of fluid flow through a model array of mantis shrimp chemosensory sensilla. J Exp Biol 203 3795-3808... [Pg.237]

ASME recently approved a Standard covering Measurement of Fluid Flow in Closed Conduits with Orifice, Nozzle and Venturi. This has been proposed to ANSI. [Pg.3]

Measurement of fluid flow in pipes, udng oti e, nozzle, and Venturi... [Pg.66]

Viscosity describes the tendency of fluids to resist reciprocal laminar displacement of two adjacent layers the so-called "inner friction". Viscosity is therefore a measure of fluid flow resistance. 1 % solutions of sodium hyaluronate (e.g., Hea-lon or Proviso ) show a viscosity 400,000 times higher than aqueous fluid. They are dependent on concentration, molecular weight, addition of solvent, and temperature. Viscosity can usually be determined by placing a certain amount of viscous fluid between two parallel plates of equal size at a predetermined distance from one another and sliding them in the same direction, at different speeds (Fig. 10). [Pg.8]

A temperature-sensitive resistor has a high enough temperature coefficient of resistance, indicating a variation of electrical resistivity with temperature. A temperature-sensitive resistor used for the measurement of fluid flow generally takes the form of either a hot wire or a hot film. When cooled by the surrounding fluid, its electrical resistance decreases, which reflects the flow rate of the fluid. [Pg.3245]

The measurement of fluid flow characteristics in real processes is quite difficult due to the opacity and high temperature characteristics. In addition, model experiments using molten metals as in the real process are often cumbersome. The situation is further complicated when heat and mass transfer, and chemical reactions occur simultaneously. Under these severe and complex conditions, it is very difficult to carry out experimental investigations on the real processes in order to improve efficiency or to develop novel processes. [Pg.1]

ISO Recommendations R-541, Measurement of Fluid Flow by Means of Orifice Plates and Nozzles, January 1967. [Pg.550]

MFC-lM-1991 Glossary of Terms Used in the Measurement of Fluid Flow in Pipes Order No. J06591 29.00... [Pg.884]

MFC-14M-1995 Measurement of Fluid Flow Using Small Bore Precision Orifice Meters... [Pg.884]

MFC-16M-1995 Measurement of Fluid Flow in Closed Conduits by Means of Electromagnetic Flowmeters Order No. K13895 30.00... [Pg.884]

American Society of Mechanical Engineers Standard, Measurement of Fluid Flow in Pipes Using Orifice, Nozzle, and Venturi. [Pg.200]

Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...