Manganese corrosion resistant alloys

Al—Mg—Mn. The basis for the alloys used as bodies, ends, and tabs of the cans used for beer and carbonated beverages is the Al—Mg—Mn alloy system. It is also used in other appHcations that exploit the excellent weldabiUty and corrosion resistance. These alloys have the unique abiUty to be highly strain hardened yet retain a high degree of ductOity. Some of the manganese combines with the iron to form AF(Fe,Mn) or constituent... 

Iron is added in small (usually 0.5—1.0 wt %) amounts to increase strength. More importantly, iron additions also enhance corrosion resistance, especially when precautions are taken to retain the iron in solution. Precipitation of the iron—nickel-rich phase does not result in strengthening and can cause degradation of corrosion resistance (47). A small (up to 1.0 wt %) amount of manganese is usually added to both react with sulfur and deoxidi2e the melt. These copper alloys are most commonly applied where corrosion resistance is paramount, as in condenser tube or heat exchangers. 

Aluminum Aluminum alloys have unusual ability to maintain strength and shock resistance at temperatures as low as —250°C (—425°F). Good corrosion resistance and relatively low cost make these alloys very popular for low-temperature equipment. For most welded construction the 5000-series aluminum alloys are widely used. These are the aluminum-magnesium and aluminum-magnesium-manganese materials. 

Steel is essentially iron with a small amount of carbon. Additional elements are present in small quantities. Contaminants such as sulfur and phosphorus are tolerated at varying levels, depending on the use to which the steel is to be put. Since they are present in the raw material from which the steel is made it is not economic to remove them. Alloying elements such as manganese, silicon, nickel, chromium, molybdenum and vanadium are present at specified levels to improve physical properties such as toughness or corrosion resistance. 

Most published work has focused on the deposition of Ni, Co, and NiCo alloys from hypophosphite electrolytes [14], and this part of the review will deal primarily with these alloys. Other Co alloys studied include CoZnP [15, 16], the recording characteristics of which were described by Soraya [17] CoSnP [18], which is reported to have enhanced corrosion resistance and the rhenium and manganese alloys used for vertical recording, discussed below. Other reductants, such as hydrazine [19], dimethylamine borane [20-22], pyridine borane [23], and borohydride [24, 25], can be used for the chemical deposition of nickel and cobalt, but to date there has been no significant application of these to the technology of magnetic media. 

Ferro-alloys Master alloys containing a significant amount of bon and a few elements more or less soluble in molten bon which improve properties of bon and steels. As additives they give bon and steel better characteristics (increased tensile sbength, wear resistance, corrosion resistance, etc.). For master alloy production carbothermic processes are used for large-scale ferro-sihcon, ferro-chromium, ferro-tungsten, ferro-manganese, ferro-nickel and metallothermic processes (mainly alumino and sihco-thermic) for ferro-titanium, ferro-vanadium, ferro-molybdenum, ferro-boron. 

High-carbon austenitic structures can be preserved at ambient temperatures if the iron is alloyed with sufficient nickel or manganese, since these metals form solid solutions with 7-Fe but not with a-Fe. If over 11% chromium is also present, we have a typical austenitic stainless steel. Such steels are corrosion resistant, nonmagnetic, and of satisfactory hardness, but, because the a-Fe 7-Fe transition is no longer possible, they cannot be hardened further by heat treatment. Figure 5.9 summarizes these observations. 

Most of these alloys are of proprietary compositions and are known by a variety of trade names. Silicon content ranges from 1.5 to 3.5% usually less than 1.5% zinc content. Tin, manganese, and iron also may be added in small quantities. Because of their excellent strength, ease of welding, and corrosion resistance, the alloys have become important construction materials. As the silicon content increases, the allays become mure subject to fire cracking. 

An acid-resisting alloy known as illium contains Ni 60-65, Cu 6-42, Cr 21-07, Mo 4-67, W 2-13, with traces of aluminium, silicon, iron, and manganese. It melts at 1300° C., and has a tensile strength of 50,000 lb. per square inch. It is remarkably resistant to corrosion, a 25 per cent, solution of nitric acid having no apparent influence upon it in twenty-four hours.2... 

---