Loading out

The accept and downgrade buttons are interlocked with a sensor device, so that a block must be scanned at least once before the block can be accepted and loaded out by the operator This function will however always be overruled by the programmed safety time limit, which will automatically reject and outload the block when the allowed exposure time has elapsed. 

A novel global LNG market is for vehicle fuels. Liquefaction facilities for vehicle usage may essentially be the same as peak shaving units however, LNG storage is much smaller and is prone to load out the fuel as a liquid rather than vaporized gas. Different process cycles are developed. 

The cooled discharge mass is loaded out of the reactor into the bin and transported into the baking department. 

The solid product of hydrolysis is loaded out of the nutsch filter, weighed and sent into reactor 14 through a hatch the reactor also receives solid sodium hydroxide. After that, backflow condenser 13 is filled with water, the agitator is switched on and the reactive mixture is gradually filled with ethyl alcohol (or hydrosite) from batch box 72 at such speed that the temperature in the reactor does not exceed 80 °C. After the whole mixture has been introduced, the jacket is filled with vapour and agitated for 1-2 hours at 75-80 °C. The mixture is cooled to 20 °C and poured into... 

To purify TMPhT from mechanical impurities, the product is subjected to additional filtration in vacuum filter 12. The ready product is loaded out of vacuum filter 12 into collector 13. 

The mixture is loaded out of the reactor into tank 16 to distil tetraethyllead. The tank should already be filled with ground sulfure and ferric iron chloride. Iron chloride reduces the alkalinity of the dross and improves its consistency due to the formation of the colloid solution of iron hydroxide ground sulfure is uniformly distributed through the dross, also improving its consistency and preventing clotting of lead particles. 

The etherification of phosphorus chlorooxide with cresol is carried out in etherificator 5, a cast iron cylindrical apparatus lined with two layers of diabase tiles. The reactor is filled with a necessary amount of phosphorus chlorooxide from batch box 2 magnesium chloride is loaded through a hatch and dried cresol is loaded out of batch box 1. After the reactants have been loaded, the apparatus is heated to 80 °C. The reaction is started at this temperature, but then it is gradually raised to 170 °C. At 170 °C the mixture is held for about 5 hours after that, the acidity number is determined. When the acidity number is 30 mg KOH/g, the reaction is stopped. 

Preparation of sodium p-nitrophenolate. The production of sodium p-nitrophenolate (p-NphNa) is conducted periodically in reactor 1 (Fig. 108). First of all, p-nitrophenol is loaded out of wooden cylinders into agitator 2 at agitation. Agitator 2 has been filled with a necessary amount of hot water (75-80 °C). In the agitator pieces of p-nitrophenol are ground, forming... 

Current industry trends are toward the installation of enclosed conveyors and the construction of enclosed areas with negative pressure aspiration for oilseed unloading and meal load-out. Highly efficient dust collection systems and control equipment (cyclones and bag houses) are used throughout the processes to control both fugitive and point source emissions. 

F - fresh catalyst (after 100 h of work loaded out of the central part of the catalyst bed), F-B300/14 - fresh catalyst after 14 h of barotheimal treatment at 300jC ... 

The properties of VPBiO catalyst loaded out of the industrial unit central zone after... 

Excess feed that overflows through the chute (30), poor quality briquettes, or chips from the screen (17) as well as chips and fines from the load-out screen (20) are collected by conveyors (22 and 24) and transported to the reject hopper (23). From there, the material is extracted at a controlled rate and is conditioned... 

Moist particulate solid wastes, such as predried FGD gypsum filter cake, can be extruded (Fig. 8.20) in, for example, flat die pellet presses (4 in Fig. 8.20) yielding cylindrical agglomerates, which are dried and screened prior to load-out. 

The products are stored in bunkers, from which they can be either loaded out, or transferred to another plant for grinding (section 17.2) or hydrating (section 20.3). 

Another truck that raises the operator with the load is the order picker truck. However, unlike the above trucks which are designed primarily for unit load in and unit load out, an order picker track allows the operator to start with an empty pallet (or magazine) and stack various containers or parts on it as he/she picks the appropriate parts/products from unit loads stored in the rack. 

After unloading the last FSA of start-up load out of the core the reactor goes into the self-maintaining operation regime. Thus criticality is maintained mainly by own plutonium and reactor... 

Skip loading To ensure that the right cunount of material is loaded into the skip each sequence has to be mejisured (weight md volume). This can be achieved by either a high speed conveyor load-out system or a loading pocket. 

Advantages for a high speed conveyor load-out system ... 

Small impact on head ropes during loading the into skip Disadvantages for a high speed conveyor load-out system ... 

Loading pocket causes increased maintenance costs (near the shaft) Recommendation—High speed conveyor load-out system with load cells and volume measuring. 

High-Speed Load-Out Conveyor Designs and Skip Loading Time Optimization... 

---