Large-diameter lines

High temperature lines that grow due to thermal expansion are supported by shoes welded or strapped to the bottom of the pipe at the pipe support locations. Insulated lines must have insulation breaks at the support or be supported by shoes. Large-diameter lines are often used to support smaller lines at locations in between the supports by miming a support beam attached to two larger-sized lines below the smaller lines. 

Ductile fracture of large diameter line pipe showing scalloped fracture edges.120... 

Three major kinds of steel are used for large diameter line pipe operating under extreme climatic... 

Figure 8.31 Large diameter lined elbow and tee. (Courtesy RMB Products.)...

Figure 7-54 shows one level of yard piping. Regardless of the service, heavy lines (very large diameter lines, large lines full of liquid) are placed... 

In almost all plants, spacing between yard support bents is about 16 to 20 feet. Neverless, consideration should be given to (a) line sizes smaller lines have to be supported more frequently than large diameter lines (b) liquid filled lines require a shorter span than gas lines (c) line temperature very hot lines span shorter distances than cold ones of same size and wall thickness (d)... 

C906 PE plastic pipe for water distribution and large diameter line pipe... 

Semi-submersible rigs are often referred to as semis , and are a floating type of rig. Like the jack-up, a semi is self contained. The structure is supported by large pontoons which are ballasted with water to provide the required stability and height. The rig is held in position by anchors and mooring lines or dynamically positioned by thrusters. A large diameter steel pipe ( riser ) is connected to the sea-bed and serves as a conduit for the drill string. The blowout preventer (BOP) is also located at the sea-bed ( sub sea stack ). 

Multielevation piperacks are usually needed to handle all the required services for piping, electrical, utilities, and instmmentation. The two-level rack is one of the most common but three-level ones are also used. The utility lines are usually mn in the upper level and the process lines in the lower levels. The larger-diameter lines are located to the outside of the rack to be closest to the column supports. Access platforms are required at the battery limit to provide operators access to the block valves and blinds. If long mns of hot pipe are required, a portion of the pipe rack needs to be dedicated to an expansion loop. A horizontal space in the piperack is provided for a set of lines to be flat-turned into a set of expansion loops with the large pipes located on the outside. AH of the pipe turns are in the same horizontal plane, which is an exception to normal piping practice. A flat turn takes up and blocks space for other pipes. Flat turns are generally only made from the outside of the rack to minimize this blockage. 

Cost rules out almost all alternative materials for long-distance pipe lines it is much cheaper to build and protect a mild steel pipe than to use stainless steel instead - even though no protection is then needed. The only competing material is a polymer, which is completely immune to wet corrosion of this kind. City gas mains are now being replaced by polymeric ones but for large diameter transmission lines, the mechanical strength of steel makes it the preferred choice. 

The calender was developed over a century ago to produce natural rubber products. With the developments of TPs, these multimillion dollar extremely heavy calender lines started using TPs and more recently process principally much more TP materials. The calender consists essentially of a system of large diameter heated precision rolls whose function is to convert high viscosity plastic melt into film, sheet, or coating substrates. The equipment can be arranged in a number of ways with different combinations available to provide different specific advantages to meet different product requirements. Automatic web-thickness profile process control is used via computer, microprocessor control. 

Quenching the vapour with cold air in the chamber may increase the rate of heat removal although excessive nucleation is likely and the product crystals will be very small. Condenser walls may be kept free of solid by using internal scrapers, brushes, and other devices, and all vapour lines in sublimation units should be of large diameter, be adequately insulated, and if necessary, be provided with supplementary heating to minimise blockage due to the buildup of sublimate. One of the main hazards of air-entrainment sublimation is the risk of explosion since many solids that are considered safe in their normal state can form explosive mixtures with air. All electrical equipment should therefore be flame-proof, and all parts of the plant should be efficiently earthed to avoid build-up of static electricity. 

---