Joining control

An important consideration in scheduling is the effect of control flow in a behavioral description. As shown in Figure 8, if-then-else and case statements imply an exclusive fork-join control block in the CDFG. Operations in the different branches of a block are mutually exclusive if they are scheduled within the control block s boundary. When similar operations in different branches are scheduled into the same c-step, a single FU is required since the operations will never execute concurrently. 

A typical noisy light based CRS experiment involves the splitting of a noisy beam (short autocorrelation time, broadband) into identical twin beams, B and B, tlnough the use of a Michelson interferometer. One ami of the interferometer is computer controlled to introduce a relative delay, x, between B and B. The twin beams exit the interferometer and are joined by a narrowband field, M, to produce the CRS-type third order polarization in the sample ([Pg.1209]

III-V compound semiconductors with precisely controlled compositions and gaps can be prepared from several material systems. Representative III-V compounds are shown in tire gap-lattice constant plots of figure C2.16.3. The points representing binary semiconductors such as GaAs or InP are joined by lines indicating ternary and quaternary alloys. The special nature of tire binary compounds arises from tlieir availability as tire substrate material needed for epitaxial growtli of device stmctures. 

An even wider range of wavelength, toward the infrared, can be covered with quantum well lasers. In the Al Ga As system, compressively strained wells of Ga In As are used. This ternary system is indicated in Figure 6 by the line joining GaAs and In As. In most cases the A1 fraction is quite small, X < 0.2. Such wells are under compressive strain and their thickness must be carefully controlled in order not to exceed the critical layer thickness. Lasers prepared in this way are characterized by unusually low threshold current density, as low as ca 50 A/cm (l )-... 

Adhesives. Contact adhesives are blends of mbber, phenoHc resin, and additives suppHed in solvent or aqueous dispersion form they are typically appHed to both surfaces to be joined (80). Evaporation of the solvent leaves an adhesive film that forms a strong, peel-resistant bond. Contact adhesives are used widely in the furniture and constmction industries and also in the automotive and footwear industries. The phenoHc resins promote adhesion and act as tackifiers, usually at a concentration of 20—40%. In solvent-based contact adhesives, neoprene is preferred, whereas nitrile is used in specialty appHcations. The type and grade of phenoHc resin selected control tack time, bond strength, and durabiHty. 

Magnesium anodes are usually built into the object to be protected through isolating sockets or holes (see Fig. 20-6) and joined to them with cables. They must be readily accessible and easily exchangeable for convenient control [4]. The directions for use have to indicate the necessity for an inspection after 2 years of operation. During operation, control can be exercised by electrical measurements (current, resistance). In addition, acoustic and optical methods exist to determine the amount of anode consumption [4]. The life of the anodes is usually more than 5 years (see Section 6.6). 

The toughness of interfaces between immiscible amorphous polymers without any coupling agent has been the subject of a number of recent studies [15-18]. The width of a polymer/polymer interface is known to be controlled by the Flory-Huggins interaction parameter x between the two polymers. The value of x between a random copolymer and a homopolymer can be adjusted by changing the copolymer composition, so the main experimental protocol has been to measure the interface toughness between a copolymer and a homopolymer as a function of copolymer composition. In addition, the interface width has been measured by neutron reflection. Four different experimental systems have been used, all containing styrene. Schnell et al. studied PS joined to random copolymers of styrene with bromostyrene and styrene with paramethyl styrene [17,18]. Benkoski et al. joined polystyrene to a random copolymer of styrene with vinyl pyridine (PS/PS-r-PVP) [16], whilst Brown joined PMMA to a random copolymer of styrene with methacrylate (PMMA/PS-r-PMMA) [15]. The results of the latter study are shown in Fig. 9. 

Polychloroprene rubber (CR) is the most popular and versatile of the elastomers used in adhesives. In the early 1920s, Dr. Nieuwland of the University of Notre Dame synthesized divinyl acetylene from acetylene using copper(l) chloride as catalyst. A few years later, Du Pont scientists joined Dr. Nieuwland s research and prepared monovinyl acetylene, from which, by controlled reaction with hydrochloric acid, the chloroprene monomer (2-chloro-l, 3-butadiene) was obtained. Upon polymerization of chloroprene a rubber-like polymer was obtained. In 1932 it was commercialized under the tradename DuPrene which was changed to Neoprene by DuPont de Nemours in 1936. 

There are a number of powerful synthetic reactions which join two trigonal carbons to form a CC single bond in a stereocontrolled way under proper reaction conditions. Included in this group are the aldol, Michael, Claisen rearrangement, ene and metalloallyl-carbonyl addition reactions. The corresponding transforms are powerfully stereosimplifying, especially when rendered enantioselective as well as diastereoselective by the use of chiral controller groups. Some examples are listed in Chart 20. 

Relationships between stereocenters vary between two extremes. On the one hand, stereocenters may interact strongly in a spatial sense if they are directly joined, proximate to one another, or part of a compact rigid-ring structure. On the other hand, two stereocenters which are remote from one another and/or flexibly connected may be so independent that one cannot be used to provide substrate spatial control for the other. Nonetheless, this latter type of stereorelationship may still be clearable if the target molecule can be disconnected to divide the two stereocenters between two precursors or if an appropriate enantioselective transform is available. 

Also in 1950 Sakliarov and Tamm proposed an idea for a controlled thermonuclear fusion reactor, the TOKAMAK (acronym for the Russian phrase for toroidal chamber with magnetic coiF ), which achieved the highest ratio of output power to input power of any fusion device of the twentieth centuiy. This reactor grew out of interest in a controlled nuclear fusion reaction, since 1950. Sakharov first considered electrostatic confinement, but soon came to the idea of magnetic confinement. Tamm joined the effort with his work on particle motion in a magnetic field, including cyclotron motion, drifts, and magnetic surfaces. Sakharov and Tamm realized that... 

---