Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Insulation metal building

A mercury-in-glass thermometer having e 0.9 hangs in a metal building and indicates a temperature of 20°C. The walls of the building are poorly insulated and have a temperature of 5°C. The value of h for the thermometer may be taken as 8.3 W/m °C. Calculate the true air temperature. [Pg.470]

Pre-engineered metal buildings including foundation, insulation, doors, trim, and lighting 40/ft. ... [Pg.287]

The insulation markets holding tremendous potential for penetration during the current decade include commercial, industrial (retrofit and new construction), residential (retrofit and new construction) farm buildings and metal buildings. [Pg.50]

Metal Building Segment. The present market potential for insulation materials is 293,000,000 square feet. We estimate... [Pg.52]

The ability to print complex multilayer stacks and the ability to separate the deposition and patterning steps effectively make nTP a powerful tool for building devices on plastic. For example. Loo and coworkers demonstrated the versatility of nTP by fabricating metal-insulator-metal capacitors on plastic at ambient conditions... [Pg.455]

Mexims. Matched Expansion Insulator/ Metal Systems. These are ceramic-to-metal seals. (Trade-name English Electric Co., Stafford, England). MG-Block, MG-plank. Perforated building units, 9in x AVz x 9in (228 x 114 x 228 mm) (block) or storey-height (plank), made from fired clay. Developed by the Mellor Green Laboratories of British Ceramic Research Ltd. [Pg.201]

Mineral-insulated, metal-sheathed (MIMS) cable is suitable for use in most environments, but it is not so suitable for use where there may be vibration. In an old paint spray booth which predated the Highly Flammable Liquids and Liquefied Petroleum Gases Regulations, a spider-frame-mounted, electrical extractor fan had been positioned at the mouth of the extract duct and connected by MIMS cable. The fan motor was totally enclosed and explosion-protected as the paints used were flammable. The maintenance was poor and paint accumulations were allowed to build up on the fan blades causing an imbalance and vibration. This led to embrittlement of the copper sheath of the cable, which cracked and broke. Then one of the conductors fractured and sparking occurred between the ends. Ignition of the spray started a fire in the paint accumulations on nearby surfaces and the factory was burnt down. [Pg.21]

Decorative panels are made by laminating vinyl or wood veneer to structural panels which can be steel, aluminum, pl)nvood, or particle board. Foam cores between the structural panels offer stiffness, sound deadening, and thermal insulation. Metal-polymer laminates are used as decorative panels in buildings. A viscoelastic core can be added between the metal sheets for sound damping. [Pg.197]

Stmctural insulation boards are used primarily for wall sheathing in constmctions where wall diaphragm racking resistance is provided by other means, such as stmctural panel corner bracing or metal strip bracing. Where allowed by building codes, these methods of constmction do provide more economical constmction. [Pg.386]

Building Wires. These wires conduct electricity at relatively low voltages (eg, 110 V and 220 V). Typically they contain a metallic conductor (copper or aluminum) that is insulated with polymeric compounds based on polyethylene or PVC which are appHed over a conductor using an extmder. [Pg.323]

So that the function of the spark gap isolators is not cancelled, cables with lightning protection must have insulated sleeves installed at their ends, in addition to the spark gap isolators, so that the metal sheathing or the shield that is connected at soldered joints to the lightning reinforcement is also separated from the operational ground of the building (foundation ground) and from the ground at the remote end. [Pg.332]

Insulation is widely used in laminate form with plasterboard, chipboard, cement board, and metal sheeting, etc. Applications are generally as lining board systems in buildings but prefabricated metal panels and ceiling tiles are also produced. [Pg.120]

Mineral wool is perhaps the best known of the whole range of insulation types. It is widely used in all sectors of industry, transport and building for thermal, acoustic and fire-protection purposes. There is a common misconception that mineral wool is a specific product type - it is not. Mineral wool is a generic name for a range of man-made non-metallic inorganic fibers. The following definitions should help to clarify the situation ... [Pg.120]

Contacts are the elementary building blocks for all electronic devices. These include interfaces between semiconductors of different doping type (homojunctions) or of different composition (heterojunctions), and junctions between a metal and a semiconductor, which can be either rectifying (Schotlky junction) or ohmic. Because of their primary importance, the physics of semiconductor junctions is largely dealt with in numerous textbooks [11, 12]. We shall concentrate here on basic aspects of the metal-semiconductor (MS) and, above all, metal-insulator-semiconductor (MIS) junctions, which arc involved in the oiganic field-effect transistors. [Pg.245]


See other pages where Insulation metal building is mentioned: [Pg.674]    [Pg.24]    [Pg.361]    [Pg.399]    [Pg.375]    [Pg.519]    [Pg.121]    [Pg.226]    [Pg.179]    [Pg.166]    [Pg.54]    [Pg.219]    [Pg.204]    [Pg.314]    [Pg.45]    [Pg.353]    [Pg.326]    [Pg.332]    [Pg.291]    [Pg.291]    [Pg.298]    [Pg.353]    [Pg.312]    [Pg.7]    [Pg.52]    [Pg.33]    [Pg.70]    [Pg.175]    [Pg.100]    [Pg.292]    [Pg.1072]    [Pg.461]    [Pg.612]    [Pg.258]    [Pg.340]    [Pg.109]    [Pg.110]   
See also in sourсe #XX -- [ Pg.52 ]




SEARCH



Building insulation

© 2024 chempedia.info