Inorganics, volume

Relative (a) tensile modulus and (b) yield stress of polypropylene nanocomposites plotted as a function of inorganic volume fraction of filler. The dotted lines serve as guides. (Reproduced from Mittal, V., Eur. Polym. 43, 3727, 2007. With permission from Elsevier.)... 

E and E correspond to the elastic moduli of composite and matrix, respectively represents the shape factor, which is dependent on filler geometry and loading direction q)f is the inorganic volume fraction 11 is given by the expression... 

Reviews of batch calorimeters for a variety of applications are published in the volume on Solution Calorimetry [8] cryogenic conditions by Zollweg [22], high temperature molten metals and alloys by Colinet andPasturel [19], enthalpies of reaction of inorganic substances by Cordfunke and Ouweltjes [16], electrolyte... 

Absolute diethyl ether. The chief impurities in commercial ether (sp. gr. 0- 720) are water, ethyl alcohol, and, in samples which have been exposed to the air and light for some time, ethyl peroxide. The presence of peroxides may be detected either by the liberation of iodine (brown colouration or blue colouration with starch solution) when a small sample is shaken with an equal volume of 2 per cent, potassium iodide solution and a few drops of dilute hydrochloric acid, or by carrying out the perchromio acid test of inorganic analysis with potassium dichromate solution acidified with dilute sulphuric acid. The peroxides may be removed by shaking with a concentrated solution of a ferrous salt, say, 6-10 g. of ferrous salt (s 10-20 ml. of the prepared concentrated solution) to 1 litre of ether. The concentrated solution of ferrous salt is prepared either from 60 g. of crystallised ferrous sulphate, 6 ml. of concentrated sulphuric acid and 110 ml. of water or from 100 g. of crystallised ferrous chloride, 42 ml. of concentrated hydiochloric acid and 85 ml. of water. Peroxides may also be removed by shaking with an aqueous solution of sodium sulphite (for the removal with stannous chloride, see Section VI,12). 

Physical Properties. Physical properties of importance include particle size, density, volume fraction of intraparticle and extraparticle voids when packed into adsorbent beds, strength, attrition resistance, and dustiness. These properties can be varied intentionally to tailor adsorbents to specific apphcations (See Adsorption liquid separation Aluminum compounds, aluminum oxide (alumna) Carbon, activated carbon Ion exchange Molecular sieves and Silicon compounds, synthetic inorganic silicates). 

Traditional adsorbents such as sihca [7631 -86-9] Si02 activated alumina [1318-23-6] AI2O2 and activated carbon [7440-44-0], C, exhibit large surface areas and micropore volumes. The surface chemical properties of these adsorbents make them potentially useful for separations by molecular class. However, the micropore size distribution is fairly broad for these materials (45). This characteristic makes them unsuitable for use in separations in which steric hindrance can potentially be exploited (see Aluminum compounds, aluminum oxide (ALUMINA) Silicon compounds, synthetic inorganic silicates). 

Oxidizers. The characteristics of the oxidizer affect the baUistic and mechanical properties of a composite propellant as well as the processibihty. Oxidizers are selected to provide the best combination of available oxygen, high density, low heat of formation, and maximum gas volume in reaction with binders. Increases in oxidizer content increase the density, the adiabatic flame temperature, and the specific impulse of a propellant up to a maximum. The most commonly used inorganic oxidizer in both composite and nitroceUulose-based rocket propellant is ammonium perchlorate. The primary combustion products of an ammonium perchlorate propellant and a polymeric binder containing C, H, and O are CO2, H2, O2, and HCl. Ammonium nitrate has been used in slow burning propellants, and where a smokeless exhaust is requited. Nitramines such as RDX and HMX have also been used where maximum energy is essential. 

Fire Resista.nce. Many fillers, particularly inorganic oxides, are noncombustible and provide a measure of passive fire resistance to filled plastics by reducing the volume of combustible matter in the filled composition. Depending on their density, they may also serve as insulation. 

Inert Gas Dilution. Inert gas dilution involves the use of additives that produce large volumes of noncombustible gases when the polymer is decomposed. These gases dilute the oxygen supply to the flame or dilute the fuel concentration below the flammability limit. Metal hydroxides, metal carbonates, and some nitrogen-producing compounds function in this way as flame retardants (see Flame retardants, antimony and other inorganic compounds). 

Sprays are the most common means of insecticide appHcation and generally involve the use of water as the principal carrier, although volatile oils sometimes are used. With the older inorganic insecticides, suspensions in water were used at dilutions of 0.1 ndash 0.2%. The development of the more effective organic insecticides has allowed the widespread use of concentrate sprays in which the toxicant is contained at 10 ndash 98% and the amount of carrier to be appHed is enormously reduced. The use of concentrate or ultralow volume sprays has brought about a revolution in spray equipment away... 

The lUPAC Commission on Nomenclature of Inorganic Chemistry continues its work, which is effectively open-ended. Guidance in the use of lUPAC rules (38) as well as explanations of their formulation (39) are available. A second volume on nomenclature of inorganic chemistry is in preparation it will be devoted to specialized areas. Some of the contents have had preliminary pubHcation in the journal Pure andJipplied Chemist, eg, "Names and Symbols of Transfermium Elements" in 1944. 

Spheres. HoUow spherical fillers have become extremely useflil for the plastics industry and others. A wide range of hoUow spherical fillers are currently available, including inorganic hoUow spheres made from glass, carbon, fly ash, alumina, and 2h conia and organic hoUow spheres made from epoxy, polystyrene, urea—formaldehyde, and phenol—formaldehyde. Although phenol—formaldehyde hoUow spheres are not the largest-volume product, they serve in some important appHcations and show potential for future use. 

Fig. 2. 1993 Production volumes for (a) principal inorganic pigments ia units of millions of metric tons, and (b) some of the other pigments in thousands...

---