Radiation sources infrared

With the recently developed spin-flip laser a monochromatic and powerful infrared radiation source is available which can be tuned within the S/mi—lOOjum region. 

Fig. 10. Infrared radiation source with temperature controller. Infrared Industries, Inc)...

Because of its high operating temperature and the energy distribution in the middle infrared spectrum area the Nernst stick is the most used infrared radiation source. However, it is mechanically very sensitive and can be deformed by heating. This can change the optical characteristics of the spectrophotometer. 

There are a few common methods of measuring oxygen concentration in the gas phase. Electrochemical sensors and paramagnetic sensors are typically used to measure oxygen concentration on a wet and dry basis, respectively. Carbon monoxide (CO) is most commonly measured using a nondispersive infrared technique. A gas sample flows between an infrared radiation source and an infrared detector. Carbon monoxide absorbs infrared radiation, hence the difference in intensity proportional to the concentration of CO in the gas sample. 

Infrared radiation does not penetrate below the superficial layer of the skin, so that its only effect is to heat the skin and the tissues immediately below it. Except for thermal burns, the health hazard upon exposure to low-level conventional infrared radiation sources is negligible. 

Figure 10.1 Infrared radiation sources on a jet aircraft and their peak emission wavelength together, and the polar diagram of radiant intensity at various aspect angles.

INFRARED RADIATION SOURCES FOR TRANSMISSION AND REFLECTION SPECTROMETRY... 

The first requirement is a source of infrared radiation that emits all frequencies of the spectral range being studied. This polychromatic beam is analyzed by a monochromator, formerly a system of prisms, today diffraction gratings. The movement of the monochromator causes the spectrum from the source to scan across an exit slit onto the detector. This kind of spectrometer in which the range of wavelengths is swept as a function of time and monochromator movement is called the dispersive type. 

In order to achieve a reasonable signal strength from the nonlinear response of approximately one atomic monolayer at an interface, a laser source with high peak power is generally required. Conuuon sources include Q-switched ( 10 ns pulsewidth) and mode-locked ( 100 ps) Nd YAG lasers, and mode-locked ( 10 fs-1 ps) Ti sapphire lasers. Broadly tunable sources have traditionally been based on dye lasers. More recently, optical parametric oscillator/amplifier (OPO/OPA) systems are coming into widespread use for tunable sources of both visible and infrared radiation. 

Infrared instruments using a monochromator for wavelength selection are constructed using double-beam optics similar to that shown in Figure 10.26. Doublebeam optics are preferred over single-beam optics because the sources and detectors for infrared radiation are less stable than that for UV/Vis radiation. In addition, it is easier to correct for the absorption of infrared radiation by atmospheric CO2 and 1420 vapor when using double-beam optics. Resolutions of 1-3 cm are typical for most instruments. 

The primary reference method used for measuring carbon monoxide in the United States is based on nondispersive infrared (NDIR) photometry (1, 2). The principle involved is the preferential absorption of infrared radiation by carbon monoxide. Figure 14-1 is a schematic representation of an NDIR analyzer. The analyzer has a hot filament source of infrared radiation, a chopper, a sample cell, reference cell, and a detector. The reference cell is filled with a non-infrared-absorbing gas, and the sample cell is continuously flushed with ambient air containing an unknown amount of CO. The detector cell is divided into two compartments by a flexible membrane, with each compartment filled with CO. Movement of the membrane causes a change in electrical capacitance in a control circuit whose signal is processed and fed to a recorder. 

The goal of the basic infrared experiment is to determine changes in the intensity of a beam of infrared radiation as a function of wavelength or frequency (2.5-50 im or 4000—200 cm respectively) after it interacts with the sample. The centerpiece of most equipment configurations is the infrared spectrophotometer. Its function is to disperse the light from a broadband infrared source and to measure its intensity at each frequency. The ratio of the intensity before and after the light interacts with the sample is determined. The plot of this ratio versus frequency is the infrared spectrum. 

When samples are heated, they emit infrared radiation with a characteristic spectrum. The IR emission of ceramics, coals, and other complicated solids and thin films can be studied. Also, if conditions make it difficult to use an infrared source... 

In an FTIR spectrometer, a source (usually a resistively heated ceramic rod) emits infrared radiation that is focused onto an interferometer whose main components consist of a beamsplitter, fixed mirror, movable mirror, and detector. The beamsplitter divides the beam into two beams. One beam is reflected off the beamsplitter toward the fixed mirror and is then reflected back through the beamsplitter to the detector. The other beam is transmitted through the beamsplitter toward the movable mirror and is then reflected off of the beamsplitter and to the detector [1],... 

Technology Description Infrared radiators can be used as the heat source in the destruction of hazardous waste. This system (Figure 35) is made up of a primary chamber consisting of a rectangular carbon steel box lined with layers of a light weight. 

Infrared Methods Commercial instrumentation for recording infrared radiation has been available for some years and has been explored by the electrical power industry in the UK for assessing corrosion in boiler tubes at power-station shut-down. An external heal source is played onto the outside of boiler tubes at the same time as cold water is circulated inside the tubes. Hot spots due to poor heat conductivity caused by excessive corrosion product indicated areas of high corrosion. 

The main sources of infrared radiation used in spectrophotometers are (1) a nichrome wire wound on a ceramic support, (2) the Nernst glower, which is a filament containing zirconium, thorium and cerium oxides held together by a binder, (3) the Globar, a bonded silicon carbide rod. These are heated electrically to temperatures within the range 1200- 2000 °C when they will glow and produce the infrared radiation approximating to that of a black body. 

The nondestructive temperature differential test by infrared is used. In this method, heat is applied to a product and the surface is scanned to determine the amount of infrared radiation is emitted. Heat may be applied continuously from a controlled source, or the product may be heated prior to inspection. The rate at which radiant energy is diffused or transmitted to the surface reveals defects within the product. Delaminations, unbonds, and voids are detected in this manner. This test is particularly useful with RPs. 

Is the product thermally labile Most reactions using an immersion source are run at room temperature. Since fairly large amounts of infrared radiation are emitted from the light source, cooling is necessary. 

---