Influence, sources

In remote areas, CMB methods are not applicable due to the mixed influence of numberless sources. FA generally tends to uncover obviously influencing sources such as maritime, crustal, and mixed anthropogenic ones (Heidam 1981). More promising for such regions is the use of enrichment factors (Zoller et al. 1974) and of tracer systems (Rahn 1985). The enrich-... 

L. Loh and N. Venkatraman, "Diffusion of information technology outsourcing Influence sources and the Kodak effect," Information Systems Research, vol. 3, pp. 334-358,1992. 

The simulation is performed at the strategic level and other factors influencing sourcing costs and delivery time are disregarded. 

Figure 2. Project schedule vs safety influence (Source Furst 2009 and Mroszczyk 2008 cited by Kamardeen 2010).

Figure 7.1 Circles of concern/influence. (Source Adapted from Covey 2004.1...

Integral terms extending on R are reduced to iJc using Boundary Integral Elements on the boundaries of the FEM domain (especially the influence of the source field hs). Inside the FEM domain, edge elements are used to compute the reaction field. 

We can then observe ( figure 2 ) the excitation coil length influence towards the range of the signal when the probe is moved in the tube, depending of the excitation source mode ( current I, tension U or power P constant) ... 

Equations 1 and 2 shows that the distance b between the radiation source and the object has big influence on the X-ray image [8]. Therefore you have to find a compromise between a small geometrical unsharpness and a sufficient high magnification to archive an optimal... 

The latter contribute to the fluxes in time-varying conditions and provide source or sink terms in the presence of chemical reaction, but they have no influence on steady state diffusion or flow measurements in a non-reactive sys cem. 

The parameters in the original parameterization are adjusted in order to reproduce the correct results. These results are generally molecular geometries and energy differences. They may be obtained from various types of experimental results or ah initio calculations. The sources of these correct results can also be a source of error. Ah initio results are only correct to some degree of accuracy. Likewise, crystal structures are influenced by crystal-packing forces. 

Sensitivity From equations 10.32 and 10.33 we can see that the sensitivity of a fluorescent or phosphorescent method is influenced by a number of parameters. The importance of quantum yield and the effect of temperature and solution composition on f and p already have been considered. Besides quantum yield, the sensitivity of an analysis can be improved by using an excitation source that has a greater... 

Sensitivity Sensitivity in flame atomic emission is strongly influenced by the temperature of the excitation source and the composition of the sample matrix. Normally, sensitivity is optimized by aspirating a standard solution and adjusting the flame s composition and the height from which emission is monitored until the emission intensity is maximized. Chemical interferences, when present, decrease the sensitivity of the analysis. With plasma emission, sensitivity is less influenced by the sample matrix. In some cases, for example, a plasma calibration curve prepared using standards in a matrix of distilled water can be used for samples with more complex matrices. 

In many cases an optimized method may produce excellent results in the laboratory developing the method, but poor results in other laboratories. This is not surprising since a method is often optimized by a single analyst under an ideal set of conditions, in which the sources of reagents, equipment, and instrumentation remain the same for each trial. The procedure might also be influenced by environmental factors, such as the temperature or relative humidity in the laboratory, whose levels are not specified in the procedure and which may differ between laboratories. Finally, when optimizing a method the analyst usually takes particular care to perform the analysis in exactly the same way during every trial. 

When an analyst performs a single analysis on a sample, the difference between the experimentally determined value and the expected value is influenced by three sources of error random error, systematic errors inherent to the method, and systematic errors unique to the analyst. If enough replicate analyses are performed, a distribution of results can be plotted (Figure 14.16a). The width of this distribution is described by the standard deviation and can be used to determine the effect of random error on the analysis. The position of the distribution relative to the sample s true value, p, is determined both by systematic errors inherent to the method and those systematic errors unique to the analyst. For a single analyst there is no way to separate the total systematic error into its component parts. 

The principal tool for performance-based quality assessment is the control chart. In a control chart the results from the analysis of quality assessment samples are plotted in the order in which they are collected, providing a continuous record of the statistical state of the analytical system. Quality assessment data collected over time can be summarized by a mean value and a standard deviation. The fundamental assumption behind the use of a control chart is that quality assessment data will show only random variations around the mean value when the analytical system is in statistical control. When an analytical system moves out of statistical control, the quality assessment data is influenced by additional sources of error, increasing the standard deviation or changing the mean value. 

One important sem source that is not based on thermionic emission is the field emission (fe) source. Fe-sem systems typically give images of much higher resolution than conventional sems due to the much narrower energy distribution (on the order of 0.25 eV) of the primary electron beam. A fe source is a pointed W tip from which electrons tunnel under the influence of a large electric field. This different mechanism of electron generation also results in a brightness comparable to a conventional thermionic source with much less current. 

Fa.ts nd Oils. Eats and oils from rendering animal and fish offal and vegetable oilseeds provide nutritional by-products used as a source of energy, unsaturated fatty acids, and palatabiHty enhancement. Eats influence the texture in finished pet foods. The use and price of the various melting point fats is deterrnined by the type and appearance of the desired finished food appearance. 

Besides the chemical composition, porosity is another property of stone which has great influence on its preservation. An increased porosity increases the exposed surface and pores allow movement of materials such as water and its solutes through the stones. If the pores are blocked or reduced in diameter such substances may be trapped within resulting in increased local interior damage. Exposure to the climatic elements is one important source of decay. Freeze-thaw cycles, in particular, result in pressures on the pore walls of the stone s interior from changes in volume during the phase transition... 

---