Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

INDEX composition

The above discussion reveals how NR can be used to provide direct information concerning both the thickness and the composition via the SLD of the various layers in the interface. This constitutes an advantage over ellipsometry or surface plasmon resonance methods where the value of the refractive index (composition) of the film is usually assumed in order to determine its thickness. However, to use the kinematic approach to directly determine these quantities, the reflectivity has to be measured in a sufficiently large range of so that at least one-half of the longest period interference fringe, corresponding to the thirmest layer in the interface, is observed on the reflectivity curve. The spatial resolution for a film of thickness ris defined as t= 7r/Qz,max, where is the maximum momentum... [Pg.167]

We explain the method in detail below. It is imperative to fully understand the following parts of the contribution to risk in terms of (1) portfolio composition and (2) index composition. [Pg.798]

Dept. Risk Index Relative Risk % Risk Index Composite Exposure ( X1000) Composite Dollars Risk ( x 1000) Rank... [Pg.503]

Before sample preparation the sample should be thoroughly blended. In the case of grains and powdered substances, liquids, and slurries, this reduces the possibility of stratification of the material, which can be a serious source of error. Stratification can occur in liquids due to differences in temperature, refractive index, composition, density, and other factors. Blending of forages means ensuring that the correct proportion of leaves to stems is maintained, and that the sample submitted... [Pg.281]

Compared to high refractive index materials the research on low refractive index materials is less prevalent, but low refractive index composites are also a matter of interest in order to broaden the spectrum of accessible polymer materials and to achieve graded refractive index materials, for example, in antireflection coatings. ... [Pg.201]

An important application of this type of analysis is in the determination of the calculated cetane index. The procedure is as follows the cetane number is measured using the standard CFR engine method for a large number of gas oil samples covering a wide range of chemical compositions. It was shown that this measured number is a linear combination of chemical family concentrations as determined by the D 2425 method. An example of the correlation obtained is given in Figure 3.3. [Pg.52]

Figure C2.5.10. The figure gives tire foldability index ct of 27-mer lattice chains witli sets containing different number of amino acids. The sets are generated according to scheme described in [27], The set of 20 amino acids is taken as a standard sample. Each sequence witli 20 amino acids is optimized to fulfil tire stability gap [5]. The residues in tire standard samples are substituted witli four different sets containing a smaller number of amino acids [27]. The foldability of tliese substitutions is indicated by tire full circles. The open diamonds correspond to tire sequences witli same composition. However, tire amino acids are chosen from tire reduced representation and tire resultant sequence is optimized using tire stability gap [5]. Figure C2.5.10. The figure gives tire foldability index ct of 27-mer lattice chains witli sets containing different number of amino acids. The sets are generated according to scheme described in [27], The set of 20 amino acids is taken as a standard sample. Each sequence witli 20 amino acids is optimized to fulfil tire stability gap [5]. The residues in tire standard samples are substituted witli four different sets containing a smaller number of amino acids [27]. The foldability of tliese substitutions is indicated by tire full circles. The open diamonds correspond to tire sequences witli same composition. However, tire amino acids are chosen from tire reduced representation and tire resultant sequence is optimized using tire stability gap [5].
The major use of vinylpyrrohdinone is as a monomer in manufacture of poly(vinylpyrrohdinone) (PVP) homopolymer and in various copolymers, where it frequendy imparts hydrophilic properties. When PVP was first produced, its principal use was as a blood plasma substitute and extender, a use no longer sanctioned. These polymers are used in pharmaceutical and cosmetic appHcations, soft contact lenses, and viscosity index improvers. The monomer serves as a component in radiation-cured polymer compositions, serving as a reactive diluent that reduces viscosity and increases cross-linking rates (see... [Pg.114]

Solution Polymers. Acryflc solution polymers are usually characterized by their composition, solids content, viscosity, molecular weight, glass-transition temperature, and solvent. The compositions of acryflc polymers are most readily determined by physicochemical methods such as spectroscopy, pyrolytic gas—liquid chromatography, and refractive index measurements (97,158). The solids content of acryflc polymers is determined by dilution followed by solvent evaporation to constant weight. Viscosities are most conveniently determined with a Brookfield viscometer, molecular weight by intrinsic viscosity (158), and glass-transition temperature by calorimetry. [Pg.171]

Source sampling of particulates requites isokinetic removal of a composite sample from the stack or vent effluent to determine representative emission rates. Samples are coUected either extractively or using an in-stack filter EPA Method 5 is representative of extractive sampling, EPA Method 17 of in-stack filtration. Other means of source sampling have been used, but they have been largely supplanted by EPA methods. Continuous in-stack monitors of opacity utilize attenuation of radiation across the effluent. Opacity measurements are affected by the particle size, shape, size distribution, refractive index, and the wavelength of the radiation (25,26). [Pg.384]

Optical. The optical properties of fillers and the influence that fillers have on the optical properties of filled systems are often misunderstood. The key parameters in understanding the optical properties of fillers themselves are filler psd, color, and index of refraction. These characteristics influence the optical properties of filled composition, such as color, brightness, opacity, hiding power, and gloss. [Pg.367]

Whereas there is no universally accepted specification for marketed natural gas, standards addressed in the United States are Hsted in Table 6 (8). In addition to these specifications, the combustion behavior of natural gases is frequently characteri2ed by several parameters that aid in assessing the influence of compositional variations on the performance of a gas burner or burner configuration. The parameters of flash-back and blow-off limits help to define the operational limits of a burner with respect to flow rates. The yeUow-tip index helps to define the conditions under which components of the natural gas do not undergo complete combustion, and the characteristic blue flame of natural gas burners begins to show yellow at the flame tip. These... [Pg.172]


See other pages where INDEX composition is mentioned: [Pg.218]    [Pg.184]    [Pg.328]    [Pg.4]    [Pg.170]    [Pg.123]    [Pg.370]    [Pg.187]    [Pg.256]    [Pg.136]    [Pg.258]    [Pg.200]    [Pg.201]    [Pg.218]    [Pg.184]    [Pg.328]    [Pg.4]    [Pg.170]    [Pg.123]    [Pg.370]    [Pg.187]    [Pg.256]    [Pg.136]    [Pg.258]    [Pg.200]    [Pg.201]    [Pg.203]    [Pg.197]    [Pg.530]    [Pg.20]    [Pg.141]    [Pg.133]    [Pg.91]    [Pg.49]    [Pg.449]    [Pg.134]    [Pg.250]    [Pg.251]    [Pg.252]    [Pg.253]    [Pg.253]    [Pg.256]    [Pg.367]    [Pg.173]    [Pg.173]    [Pg.288]    [Pg.301]    [Pg.311]    [Pg.312]    [Pg.325]    [Pg.72]   
See also in sourсe #XX -- [ Pg.266 ]

See also in sourсe #XX -- [ Pg.204 , Pg.239 , Pg.253 ]

See also in sourсe #XX -- [ Pg.480 ]




SEARCH



Calculation of the Composite Risk Index

Composite Risk Index for All Hazardous Substances

Composite indices

Composite indices

Composite sustainability indices

Composition distribution breadth index

Compositional analyses INDEX

Flame Spread Indexes and Fire Rating of Composite Materials

INDEX composition determination

INDEX mixed composition systems

Limiting oxygen index composites

Natural fiber composites INDEX

Risk index, composite

© 2024 chempedia.info