Important factors

Polymerization reactions. Polymers are characterized by the distribution of molecular w eight about the mean as well as by the mean itself. The breadth of this distribution depends on whether a batch or plug-flow reactor is used on the one hand or a continuous well-mixed reactor on the other. The breadth has an important influence on the mechanical and other properties of the polymer, and this is an important factor in the choice of reactor. 

The first major hazard in process plants is fire, which is usually regarded as having a disaster potential lower than both explosion or toxic release. However, fire is still a major hazard and can, under the worst conditions, approach explosion in its disaster potential. It may, for example, give rise to toxic fumes. Let us start by examining the important factors in assessing fire as a hazard. 

The increase in demand for good quality white products and the reduced consumption of fuel-oil related to pollution controls are going to be important factors in residue processing and heavy oil conversion in the years to come. 

The most important factor for maturation and hydrocarbon type is therefore heat. The increase of temperature with depth is dependent on the geothermal gradient which varies from basin to basin An average value is about 3°C per 100 meters of depth. 

As probes must be manufactured individually for each different tube type, the probe development is an important factor for the economic use of the method. The classical procedure of probe development is a combination of experience and experiment. The new probe design is based on the experience with already manufactured probes. For an evaluation of the new design the probe must be manufactured. If the probe design is complicated, for example due to dual exciter coil arrangement or segmented differential detector coil systems, the costs of the development can be very high. Therefore a method for the pre-calculation of the probe performance is extremely useful. 

Attenuation is also an important factor in air-bome ultrasound. For exampe, attenuation in air at 1 MHz is 1.2 dB/cm, compared with a figure of 0.0022 dB/cm in water [1]. In addition, environmental conditions (temperature, turbulences) can affect the inspection with air-bome... 

From an electrochemical viewpoint, stable pit growtli is maintained as long as tire local environment witliin tire pit keeps tire pit under active conditions. Thus, tire effective potential at tire pit base must be less anodic tlian tire passivation potential (U ) of tire metal in tire pit electrolyte. This may require tire presence of voltage-drop (IR-drop) elements. In tliis respect the most important factor appears to be tire fonnation of a salt film at tire pit base. (The salt film fonns because tire solubility limit of e.g. FeCl2 is exceeded in tire vicinity of tire dissolving surface in tlie highly Cl -concentrated electrolyte.)... 

This lineshape analysis also implies tliat electron-transfer rates should be vibrational-state dependent, which has been observed experimentally [44]- Spin-orbit relaxation has also been identified as an important factor in controlling tire identity of botli electron and vibrational-state distributions in radiationless ET reactions. 

The very low bond dissociation enthalpy of fluorine is an important factor contributing to the greater reactivity of fluorine. (This low energy may be due to repulsion between non-bonding electrons on the two adjacent fluorine atoms.) The higher hydration and lattice enthalpies of the fluoride ion are due to the smaller size of this ion. 

The dipole moments of the hydrogen halides decrease with increasing atomic number of the hydrogen, the largest difference occurring between HF and HCl, and association of molecules is not an important factor in the properties of FICl, HBr and HI. This change in dipole moment is reflected in the diminishing permittivity (dielectric constant) values from HF to HI. 

Water-soluble globular proteins usually have an interior composed almost entirely of non polar, hydrophobic amino acids such as phenylalanine, tryptophan, valine and leucine witl polar and charged amino acids such as lysine and arginine located on the surface of thi molecule. This packing of hydrophobic residues is a consequence of the hydrophobic effeci which is the most important factor that contributes to protein stability. The molecula basis for the hydrophobic effect continues to be the subject of some debate but is general considered to be entropic in origin. Moreover, it is the entropy change of the solvent that i... 

Chapter XII is concerned with Semimicro Technique. There can be little doubt that preparations on a smaller scale than has hitherto been customary have many advantages particular reference may be made to cost, time and bench space, all of which are important factors in teaching laboratories and also in training for research. Once the student has mastered the special technique, no difficulty should be experienced in adapting most of the preparations described in the book to the semimicro scale. A few examples of small-scale preparations are included together with a suggested list of experiments for an elementary course. 

Consideration of the orientation of substitution Orientation is an important factor to be considered in recognising both changes in the effective electrophile and in the nature of the aromatic substrate. Cases of the former type, which will be met at several places... 

The little-studied conjugated base of 2-aminothiazoles is able to react on either ring nitrogen or exocvclic nitrogen. Steric hindrance of R2 and R. is clearly an important factor in this reactivity (Scheme 147). 

Table 2 3 lists the heats of combustion of several alkanes Unbranched alkanes have slightly higher heats of combustion than their 2 methyl branched isomers but the most important factor is the number of carbons The unbranched alkanes and the 2 methyl branched alkanes constitute two separate homologous senes (see Section 2 9) m which there is a regular increase of about 653 kJ/mol (156 kcal/mol) m the heat of combustion for each additional CH2 group... 

To summarize the most important factor to consider m assessing carbocation sta bility IS the degree of substitution at the positively charged carbon... 

Analogous data for a host of alkenes tell us that the most important factors gov emmg alkene stability are... 

Steric effects may be an even more important factor m controlling the regioselec tivity of addition Boron with its attached substituents is much larger than a hydrogen atom and becomes bonded to the less crowded carbon of the double bond whereas hydrogen becomes bonded to the more crowded carbon... 

The major influence of the methyl group is electronic The most important factor IS relative carbocation stability To a small extent the methyl group sterically hinders the ortho positions making attack slightly more likely at the para carbon than at a single ortho carbon However para substitution is at a statistical disadvantage because there are two equivalent ortho positions but only one para position... 

The carbonyl carbon of a ketone bears two electron releasing alkyl groups an aldehyde carbonyl group has only one Just as a disubstituted double bond m an alkene is more stable than a monosubstituted double bond a ketone carbonyl is more stable than an aldehyde carbonyl We 11 see later m this chapter that structural effects on the relative stability of carbonyl groups m aldehydes and ketones are an important factor m then rel ative reactivity... 

Precision For samples and standards in which the concentration of analyte exceeds the detection limit by at least a factor of 50, the relative standard deviation for both flame and plasma emission is about 1-5%. Perhaps the most important factor affecting precision is the stability of the flame s or plasma s temperature. For example, in a 2500 K flame a temperature fluctuation of +2.5 K gives a relative standard deviation of 1% in emission intensity. Significant improvements in precision may be realized when using internal standards. 

Besides resolution, another important factor in chromatography is the amount of time required to elute a pair of solutes. The time needed to elute solute B is... 

Because volatility is such an important factor in GC, the chromatographic column is contained in an oven, the temperature of which can be closely and reproducibly controlled. For very volatile... 

Figure 2.5 shows, for a sample in the gas phase, a typical absorption line with a HWHM (half-width at half-maximum) of Av and a characteristic line shape. The line is not infinitely narrow even if we assume that the instmment used for observation has not imposed any broadening of its own. We shall consider three important factors that may contribute to the line width and shape. 

---