Humidity various

Process Requirements. Typical inside dry-bulb temperatures and relative humidities used for preparing, processing, and manufacturing various products, and for storing both raw and finished goods, are Hsted in Table 1. In some instances, the conditions have been compromised for the sake of worker comfort and do not represent the optimum for the product. In others, the conditions Hsted have no effect on the product or process other than to increase worker efficiency. 

The main advantage of wholesale climate control Hes in easy access to the objects, and the absence of differences in conditions between various spaces within the institution, eg, storage areas, conservation laboratories, and exhibition galleries. The actual values set for the rh are a matter of compromise metals, stone, and ceramics are best served by humidities as low as possible, but organic materials generally require higher values. An accepted... 

Finishing sprays and spritzes are sprayed on clean, dry hair and tested for drying time, stiffness, combing ease, flaking after combing and stickiness upon contact with moisture. Additionally, hair hoi ding properties are evaluated by measurements of the cud retention at various humidities. Standardized water-set cuds are sprayed with standard amounts of product under controlled circumstances. They are then dried, placed into vadous humidity levels, and the cud fall monitored at vadous time pedods. 

Chemical treatments commonly appHed to cormgated paperboard packaging materials include additives that impart various degrees of water resistance, humidity resistance, oil and grease resistance, product abrasion resistance, product corrosion resistance, adhesion release properties, flame-retardant properties, nonskid properties, and static electricity control properties to the finished package (1,2). 

Effective antistatic agents must act at a relative humidity below 40%, preferably below 15%. The agent must form a film on various surfaces and be apphed from a solution or dispersion in water or other inexpensive solvents. The antistatic agent must not interfere with subsequent processing of the product, impair the hand, or affect color, odor, appearance, and performance properties of the substrate. It should be nontoxic and nonflammable. 

The electrical properties will also depend on the above factors as well as on the test conditions, in particular temperature, test frequency and humidity. Table 26.12 quotes ranges for figures quoted in the literature for various electrical properties. 

Figure 28 shows the key features of the humidity chart. The chart consists of the following four parameters plotted as ordinates against temperature on the abscissas (1) Humidity H, as pounds of water per pound of dry air, for air of various relative humidities (2) Specific volume, as cubic feet of dry air per pound of dry air (3) Saturated volume in units of cubic feet of saturated mixture per pound of dry air and (4) latent heat of vaporization (r) in units of Btu per pound of water vaporized. The chart also shows plotted hiunid heat (s) as abscissa versus the humidity (H) as ordinates, and adiabatic humidification curves (i.e., humidity versus temperature). Figure 28 represents mixtures of dry air and water vapor, whereby the total pressure of the mixture is taken as normal barometric. Defining the actual pressure of the water vapor in the mixture as p (in units of mm of mercury), the pressure of the dry air is simply 760 - p. The molal ratio of water vapor to air is p/(760-p), and hence the mass ratio is ... 

We denoted the mass of dry air in a volume V as that is, p, - w,/Vj, and the mass of water vapor in V as m, that is, pp = mp/Yp. In practical calculations we usually handle volume flow volume flow is known in the suction inlet of a fan when the operating point of the fan is defined. Volume flow q, expressing the total air flow or the combined volume flow of water vapor and dry air, is not constant in various parts of the duct, because the pressure and temperature can vary. Therefore in technical calculations dealing with humid air, materia flows are treated as mass flows. Also, while the humidity can vary, the basic quantity is dry air mass flow w,(kg d.a./s). If, for instance, we know the volume flow q,. of a fan, the dry air mass flow through the fan is... 

In many cases the incoming and outgoing air flows can consist of various air flows in different states (temperature, humidity), which must be treated separately. This means that the air enthalpy flow must be divided into corresponding parts. 

TTie ability of the ventilation system to protect the worker efficiently can readily be determined by personal samples. The PIMEX method (see Chapter 12) can be used to determine the worker s exposure during various work phases. The capture efficiency as well as the supply air fraction can be measured using tracer gas techniques. Simple evaluation is carried out visually with smoke tube or pellet tests. Daily system evaluation is recommended using airflow or static pressure measurements at appropriate parts of the system. The air velocities, turbulence intensities, air temperature, mean radiant temperature, and air humidity should also be measured to provide an assessment ol thermal comfort. 

TABLE 12.5 Relative Humidity of Air over Various Saturated Solutions of Salts ... 

Table 26 Relative humidities over various concentrations of sulfuric acid at 20°C.

Several of the gas turbine cycle options discussed m this section (intercooling, recuperation, and reheat) are illustrated in Figure 4. These cycle options can be applied singly or in various combinations with other cycles to improve thermal efficiency. Other possible cycle concepts that are discussed include thermochemical recuperation, partial oxidation, use of a humid air turbine, and use of fuel cells. 

Human occupants, electrical/electronic equipment and process plant all emit varying quantities of sensible and latent heat. Equally, these various elements require (or can tolerate) differing environmental conditions. Depending on these operational constraints, the need may well exist to provide natural (or powered) ventilation to maintain environmental conditions (temperature and/or humidity) consistent with the occupational/process requirements. 

---