Heat treatment state

Experiments studying the corrosion behaviour of pipes and pipe connections made of the steel 1.4301 (SAE 304 UNS S30400) were carried out in cold drinking water in field tests lasting five years [34]. Table 20 contains data for pipes in various heat treatment states. The pipe connections were made of the same material as the pipes. Pressed fittings with a non-metallic seal and solder fittings were tested. The chemical composition of the solders used is shown in Table 21. 

Outside the pipe connections, the pipes were completely corrosion-resistant, regardless of the heat treatment state investigated. According to [30], intercrystalline corrosion should not exceed 10 mm when testing for resistance to this form of corrosion. 

Table 20 Chemical composition and heat treatment state of longitudinally welded ND 20 pipes 22 mm x 0.7 mm) consisting of 1.4301 (SAE 304, UNS S30400) [34]...

Unlike CVD, PVD invoives depositing hard materials from the chemical vapour by physical means. Materials such as hard alloys and cermets can be PVD coated, as well as steels. Depending on the steel material, its heat treatment state and the hard alloy (target material), lower treatment temperatures in the range of approx. 

In order to describe inherited stress state of weldment the finite element modelling results are used. A series of finite element calculations were conducted to model step-by-step residual stresses as well as its redistribution due to heat treatment and operation [3]. The solutions for the reference weldment geometries are collected in the data base. If necessary (some variants of repair) the modelling is executed for this specific case. 

Inactivation and Removal of Viruses. In developing methods of plasma fractionation, the possibiHty of transmitting infection from human vimses present in the starting plasma pool has been recognized (4,5). Consequentiy, studies of product stabiHty encompass investigation of heat treatment of products in both solution (100) and dried (101) states to estabHsh vimcidal procedures that could be appHed to the final product. Salts of fatty acid anions, such as sodium caprylate [1984-06-17, and the acetyl derivative of the amino acid tryptophan, sodium acetyl-tryptophanate [87-32-17, are capable of stabilizing albumin solutions to 60°C for 10 hours (100) this procedure prevents the transmission of viral hepatitis (102,103). The degree of protein stabilization obtained (104) and the safety of the product in clinical practice have been confirmed (105,106). The procedure has also been shown to inactivate the human immunodeficiency vims (HIV) (107). 

Extrusion Resins. Extmsion of VDC—VC copolymers is the main fabrication technique for filaments, films, rods, and tubing or pipe, and involves the same concerns for thermal degradation, streamlined flow, and noncatalytic materials of constmction as described for injection-molding resins (84,122). The plastic leaves the extmsion die in a completely amorphous condition and is maintained in this state by quenching in a water bath to about 10°C, thereby inhibiting recrystallization. In this state, the plastic is soft, weak, and pHable. If it is allowed to remain at room temperature, it hardens gradually and recrystallizes partially at a slow rate with a random crystal arrangement. Heat treatment can be used to recrystallize at controlled rates. 

Pitches can be transformed to a mesophase state by further chemical and physical operations. Heat treatment of conventional pitches results in additional aromatic polymeriza tion and the distillation of low molecular weight components. This results in an increase in size and concentration of large planar aromatic molecular species whereupon the precursor pitch is transformed to a mesophase state exhibiting the characteristics of nematic Hquid crystals (1). Additional heat treatment converts the mesophase pitch to an infusible aromatic hydrocarbon polymer designated as coke. 

The plate dryer is limited in its scope of apphcations only in the consistency of the feed material (the products must be friable, free flowing, and not undergo phase changes) and diying temperatures up to 320°C. Applications include speci ty chemicals, pharmaceuticals, foods, polymers, pigments, etc. Initial moisture or volatile level can be as high as 65 percent and the unit is often used as a final dryer to take materials to a bone-dry state, if necessary. The plate dryer can also be used for heat treatment, removal of waters of hydration (bound moisture), solvent removal, and as a product cooler. 

Having selected the appropriate material for an item of plant, it is imperative that this material is used in the required state of heat treatment, surface finishes, etc. for its construction. 

The mechanical properties reported in the literature for molybdenum and its alloys are frequently at variance. That this should be so is not surprising as the properties of molybdenum and its alloys are greatly affected by the prior history of the material, both thermal and mechanical. Far too often values are used without reference to the sources of the material, various states of heat treatment, etc. When mechanical properties are an important feature of the design application, advice should always be sought on the suitability as only the manufacturer has the complete data on the history of his own product. Physical and some typical mechanical properties given for general guidance are shown in Tables 5.2 and 5.3. 

---