Physical meaning

One can see from the formulas (1) and (2) that PT sensitivity strongly depends on the thickness of a developer s layer. But during liquid s penetration into developer s layer the powder particles are sinking and more tightly packing each other. It results in decrease of layer thickness h Physical meaning of the influence of this process upon defect s detection is obvious as follows. 

While the result should not have very exact physical meaning, as an exercise, calculating the f potential of lithium ion, knowing that its equivalent conductivity is 39 cm /(eq)(ohm) in water at 25°C. 

It turns out to be considerably easier to obtain fairly precise measurements of a change in the surface free energy of a solid than it is to get an absolute experimental value. The procedures and methods may now be clear-cut, and the calculation has a thermodynamic basis, but there remain some questions about the physical meaning of the change. This point is discussed further in the following material and in Section X-6. 

Thus from an adsorption isotherm and its temperature variation, one can calculate either the differential or the integral entropy of adsorption as a function of surface coverage. The former probably has the greater direct physical meaning, but the latter is the quantity usually first obtained in a statistical thermodynamic adsorption model. 

Unlike the pressure where p = 0 has physical meaning, the zero of free energy is arbitrary, so, instead of the ideal gas volume, we can use as a reference the molar volume of the real fluid at its critical point. A reduced Helmlioltz free energy in tenns of the reduced variables and F can be obtained by replacing a and b by their values m tenns of the critical constants... 

The absolute energy of a molecule in molecular nicchari ics has no iulriusic physical mean mg values are useful on ly for com-... 

The physical meaning of the sections on transformation matrices and unitary matrices is that we can try to rotate our coordinate system so that each component... 

It should be noted that the Hartree-Fock equations F ( )i = 8i ([)] possess solutions for the spin-orbitals which appear in F (the so-called occupied spin-orbitals) as well as for orbitals which are not occupied in F (the so-called virtual spin-orbitals). In fact, the F operator is hermitian, so it possesses a complete set of orthonormal eigenfunctions only those which appear in F appear in the coulomb and exchange potentials of the Foek operator. The physical meaning of the occupied and virtual orbitals will be clarified later in this Chapter (Section VITA)... 

So far as rule 2 is concerned, since AJ is conventionally taken to refer to J -J", where J is the quantum number of the upper state and J" that of the lower state of the transition, AJ = — 1 has no physical meaning (although it emerges from the quantum mechanics). It is commonly, but incorrectly, thought that AJ = +1 and AJ = — 1 refer to absorption and emission, respectively in fact AJ = +1 applies to both. Transition wavenumbers or frequencies are given by... 

Filtration is often referred to as mechanical separation because the separation is accompHshed by physical means. This does not preclude chemical or thermal pretreatment used to enhance filtration. Although some slurries separate well without chemical conditioning, most pulps of a widely varying nature can benefit from pretreatment (see Flocculating agents). 

Materials for flavoring may be divided into several groups. The most common groupings are either natural or artificial flavorings. Natural materials include spices and herbs essential oils and thek extracts, concentrates, and isolates fmit, fmit juices, and fmit essence animal and vegetable materials and thek extracts and aromatic chemicals isolated by physical means from natural products, eg, citral from lemongrass and linalool from hois de rose. 

Isolate. A relatively pure chemical produced from natural raw materials by physical means, eg, distillation, extraction, crystallization, etc, and therefore natural or by chemical means, ie, via hydrolysis, bisulfite addition products, and regeneration, etc, and therefore artificial by 1993 U.S. labeling regulations. 

Albumen has the largest number of acid and basic groups. It is the most soluble of the proteins present in a hide. The albumen is not a fibrous material, however, and therefore has no value in the leather. Keratin is the protein of the hair and the outermost surface of the hide. Unless the hair is desired for the final product it is removed by chemical and/or physical means. The elastin has Htde acid- or base-binding capacity and is the least soluble of the proteins present. The lack of reactivity of the elastin is a detriment for most leather manufacture. The presence of elastin in the leather greatly limits the softness of the leather. 

A number of other valuable aroma chemicals can be isolated from essential oils, eg, eugenol from clove leaf oil, which can also, on treatment with strong caustic, be isomerked to isoeugenol, which on further chemical treatment can be converted to vanillin (qv). Sometimes the naturally occurring component does not requke prior isolation or concentration, as in the case of cinnamaldehyde in cassia oil which, on dkect treatment of the oil by a retro-aldol reaction, yields natural ben2aldehyde (qv). This product is purified by physical means. 

Physiological Effects. The sulfur and nitrogen mustards act first as cell irritants and finally as a cell poison on all tissue surfaces contacted. The first symptoms usually appear in 4—6 h (4). The higher the concentration, the shorter the interval of time between the exposure to the agent and the first symptoms. Local action of the mustards results in conjunctivitis (inflammation of the eyes) erythema (redness of the skin), which may be followed by blistering or ulceration and an inflammatory reaction of the nose, throat, trachea, bronchi, and lung tissue. Injuries produced by mustard heal much more slowly and are much more Fable to infection than bums of similar intensity produced by physical means or by other chemicals. 

The ceramic oxide carrier is bonded to the monolith by both chemical and physical means. The bonding differs for a ceramic monolith and a metallic monolith. Attrition is a physical loss of the carrier from the monolith from the surface shear effects caused by the exhaust gas, a sudden start-up or shutdown causing a thermal shock as a result of different coefficients of thermal expansion at the boundary between the carrier and the monolith, physical vibration of the cataly2ed honeycomb, or abrasion from particulates in the exhaust air (21) (see Fig. 6d). 

Similarity Variables The physical meaning of the term similarity relates to internal similitude, or self-similitude. Thus, similar solutions in boundaiy-layer flow over a horizontal flat plate are those for which the horizontal component of velocity u has the property that two velocity profiles located at different coordinates x differ only by a scale factor. The mathematical interpretation of the term similarity is a transformation of variables carried out so that a reduction in the number of independent variables is achieved. There are essentially two methods for finding similarity variables, separation of variables (not the classical concept) and the use of continuous transformation groups. The basic theoiy is available in Ames (see the references). 

A common use of statistics in structural biology is as a tool for deriving predictive distributions of strucmral parameters based on sequence. The simplest of these are predictions of secondary structure and side-chain surface accessibility. Various algorithms that can learn from data and then make predictions have been used to predict secondary structure and surface accessibility, including ordinary statistics [79], infonnation theory [80], neural networks [81-86], and Bayesian methods [87-89]. A disadvantage of some neural network methods is that the parameters of the network sometimes have no physical meaning and are difficult to interpret. 

---