Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Hazardous electrical locations

The majority of analytical systems required for the petrochemical and refining industries are located in Hazardous Electrical Locations. [Pg.341]

ISA S12.11. 1973. Electrical Instruments in Hazardous Dust Locations. Instrument Society of America, Research Triangle Park, N. C. [Pg.151]

NFPA 497 Classification of Flammable Liquids, Gases, or Vapors and of Hazardous (Classified) Locations for Electrical Installations in Chemical Process Areas, 1997 edition. National Fire Protection Association, Quincy, MA. [Pg.155]

Electrical Equipment for Use in Class I, Division 2 Hazardous (Classified) Locations... [Pg.550]

Standard for Purged and Pressurized Enclosures for Electrical Equipment in Hazardous (Classified) Locations Recommended Practice for Classification of Class I Hazardous Locations for Electrical Installations in Chemical Plants... [Pg.551]

FPN) Through the exercise of ingenuity in the layout of electrical installations for hazardous (classified) locations, it is frequently possible to locate much of the equipment in less hazardous or in nonhazardous locations, and, thus, to reduce the amount of special equipment required. [Pg.636]

All other applicable rules contained in this Code shall apply to electrical equipment and wiring installed in hazardous (classified) locations. [Pg.636]

FPN) Explosionproof apparatus is defined in Article 100. For further information, see Explosionproof and Dust-Ignitionproof Electrical Equipment for Use in Hazardous (Classified) Locations, ANSI/UL 1203-1988. [Pg.637]

FPN No. 5) For further information on electrical system for hazardous (classified) locations on offshore oil and gas platforms, see Design and Installation of Electrical Systems for Offshore Production Platforms, ANSl/APl RP 14F-1991. [Pg.638]

FPN No. 1) For additional information on the properties and group classification of Class I materials, see Manual for Classification of Gases, Vapors, and Dusts for Electrical Equipment in Hazardous (Classified) Locations, NFPA 497M-1991, and Guide to Eire Hazard Properties ofElammable Liquids, Gases, and Volatile Solids, NFPA 325—1994. [Pg.638]

NFPA-325 Guide to Fire Hazard Properties of Flammable Liquids, Gases and Volatile Solids, (1994 ed.), NFPA-321 Basic Classification of Flammable and Combustible Liquids (1991 ed.), NFPA-497A, Classification of Class 1 Hazardous (Classified) Locations for Electrical Installations in Chemical Process Areas (1992 ed.), and NFPA-497B, Classification of Class II Hazardous (Classified) Locations for Electrical Installations in Chemical Process Areas (1991 ed.), National Fire Protection Association, Quincy, MA. [Pg.688]

Underwriters Laboratories Inc. (UL), UL 674, Safety Electric Motors and Generators for Use in Division 1 Hazardous (Classified) Locations, Third Edition, UL, Northbrook, IL, 1994. [Pg.153]

Locate electrical equipment outside of hazardous (classified) locations or replace electrical operators with manual or pneumatic operators. [Pg.158]

NFPA 497A—Recommended Practice for Classification of Class I Hazardous (Classified) Locations for Electrical Installations in Chemical Process Areas contains recommendations for wiring requirements in an enclosed area where lighter-than-air flammable gases may be released [5.12]. While these recommendations are for chemical processing areas, the releases are similar in the hazard they present to what would be found for natural gas released in repair garages. These recommendations are also illustrated in Figure 5-1. [Pg.147]

NFPA 497 (2004) Recommended practice for the classification of flammable liquids, gases or vapors and of hazardous (classified) locations for electrical installations in chemical process areas. (National Fire Protection Association). [Pg.537]

A detailed account of the factors to be considered when designing electrical distribution systems for chemical process plants and the equipment used (transformers, switch gear, and cables) is given by Silverman (1964). Requirements for electrical equipment used in hazardous (classified) locations are given in the National Electrical Code (NFPA 70), as described in Section 9.3.5. [Pg.1075]

NFPA. 1986. Manual for classification of gases, vapors, and dusts for electrical equipment in hazardous (classified) locations. Quincy, MA National Fire Protection Association, NFPA publication no. 497M. [Pg.155]


See other pages where Hazardous electrical locations is mentioned: [Pg.237]    [Pg.230]    [Pg.237]    [Pg.230]    [Pg.786]    [Pg.2300]    [Pg.2332]    [Pg.637]    [Pg.637]    [Pg.638]    [Pg.638]    [Pg.640]    [Pg.640]    [Pg.22]    [Pg.23]    [Pg.144]    [Pg.157]    [Pg.157]    [Pg.610]    [Pg.2055]    [Pg.2087]    [Pg.2524]   
See also in sourсe #XX -- [ Pg.230 ]




SEARCH



Electrical machines hazardous locations

Electricity hazards

Hazards, electrical

© 2024 chempedia.info