Hard wood dust

Synonyms/Trade Names Hard wood dust, Soft wood dust, Western red cedar dust ... 

Coal tar and pitch Hard wood dusts Vinyl chloride monomer Mineral oil Beryllium Ionising radiation... 

Toxic substances are ones which impede or prevent the function of one or more organs within the body, such as the kidneys, liver and heart. A toxic substance is, therefore, a poisonous one. Lead, mercury, pesticides and the gas carbon monoxide are toxic substances. Carcinogenic substances are ones which are known or suspected of promoting abnormal development of body cells to become cancers. Asbestos, hard wood dust, creosote and some mineral oils are carcinogenic. It is very important that the health and safety rules accompanying the substance are strictly followed. 

Hard wood dust Nasal sinuses Furniture manufacture... 

Intestinal-type adenocarcinomas (ITACs) are rare tumors of the sinonasal tract that bear a remarkable histologic resemblance to tumors arising in the intestines. Rare cases can even resemble normal small intestinal mucosa. There is an epidemiologic linkage to occupational exposure to wood dust, particularly the hard woods, as found in furniture making. ITAC is more common in males by a ratio of 4 1 and occurs over a broad age range, with an average of 58 years. 

To illustrate the problem for the product developer, one only has to enumerate the soils and surfaces. The soils can vary from simple dust and hair to dirt, hard water spots, and fingerprints to hardened grease, soap scum, and excrement. Although the usual household cleaning tasks are concentrated in only two rooms of the house, kitchen and bathroom, the number of different surfaces encountered are many. In the U.S., for example, there may be Formica , ceramic tiles, grout, lacquered wood, vinyl flooring, painted surfaces, brass, stainless steel, enamel, porcelain, aluminum, chrome, glass, marble, methyl methacrylate, and other types of plastics. All of these materials may occur within only two rooms of the same home ... 

Another Method, —Another method of flUing bad places iu wood-work is to get Ado dust, as made with a Aue rasp or Ale, and mix this dust with thm glue, and rub it into the interstices, letting it remain until hard and solid, and then finish same as the adjoining wood. Keither this nor shellac will adhere where there is oil, or where the surface to adhere has boon oiled. 

Cost savings Reinforcement Hardness Thermai insuiation Chemical resistance Wood flour, saw dust, cotton flock Glass fibers, cellulosic fibers, synthetic fibers, asbestos fibers Metallic powders, mineral powders, silica, graphite Asbestos, ceramic oxides, silica Glass fibers, synthetic fibers, metallic oxides, graphites... 

Rigid or Hard Materiai Fiooring. Ceramic tile, ceramic mosaic tile, quarry tile, slate, and marble are all examples of the more rigid flooring materials. All can be installed with adhesives. The subfloor or substrate is likely to be either a concrete slab or plywood or similar composition wood material. Once again it is important that these subfloors be clean, diy, and free from dust, dirt, oil, grease, etc. Most installations of these rigid substrates utilize similar adhesives. 

CUTTING CORNERS. If you have wall-to-wall carpet, you need to focus on the corners only every third or fourth vacuuming. You may need to use the wand or nozzle attachment for hard-to-reach parts. If your floor is a hard surface or wood, you may need to do this each time because of dust bunnies. Warning Vacuums can scratch wood floors. Check and wipe down the vacuum s wheels before you begin to get rid of grit. Switch off the beater bar and work parallel to the planks. 

We have seen that porous surfaces may be divided into those that are soft and flexible like paper, fabrics, leather, wood, etc or those that are hard and rigid like some ceramics, concrete, stone, and so on. Because they are porous they tend to absorb not only any liquids they come into contact with but also fats or greases as well as picking up dust and dirt particles. It is necessary then to make sure that all foreign matter is removed from the joint faces as a first step. 

---