Glass fibres, analysis

Hydrazine in air Lab method using sampling either onto acid-coated glass-fibre filters followed by solvent desorption or into specially constructed impingers. Linal analysis by derivatization and high performance liquid chromatography 86... 

The main features of PC are low cost, need for small sample amount, high level of resolution, ease of detection and quantitation, simplicity of apparatus and use, difficult reproducibility (because of variation in fibres) and susceptibility to chemical attack. Identification of the separated components is facilitated by the reproducible Rj values. Detection methods in PC have been reviewed [368]. Fluorescence has been used for many years as a means of locating the components of a mixture separated by PC or TLC. However, also ATR-IR and SERS are useful. Preparative PC is unsuitable for trace analysis because filter paper inevitably contains contaminants (e.g. phthalate esters, plasticisers) [369]. For that purpose an acceptable substitute is glass-fibre paper [28]. 

As microwave sample preparation has evolved, standard microwave procedures have been developed and approved by numerous standard methods organisations (ASTM, AOAC International, EPA, etc.), see ref. [64]. Examples are standard test methods for carbon black/ash content (ASTM Method D 1506-97), lead analysis in direct paint samples (ASTM Method E 1645-94), etc. Table 8.15 shows some microwave ashing references (detection weight). A French AFNOR method utilises the atmospheric pressure single-mode microwave method as an alternative sample preparation procedure for Kjeldahl nitrogen determination [84], The performance of a microwave-assisted decomposition for rapid determination of glass fibre content in plastics for QC has been described [85]. 

Figure 6.3 Diagrammatic representation of the dry reagent strips known as reagent carriers, which are used in the Boehringer Reflotron System for the chemical analysis of blood samples. Red blood cells are removed in the separating layer and the plasma passing into the glass fibre transport layer is analysed. The magnetic code carries information about the analytical procedure.

Air particulates are usually dissolved before analysis, but again, solid samples (e.g. on glass-fibre filters) have been analysed directly in furnaces. 

Keywords E glass surface analysis silane coupling agent fibre composites. 

The precipitates were separated by glass fibre filter, washed by ethanol and air-dried. In some cases X-ray diffraction (by Philips 3710) for polymorphism and SEM analysis (by Philips XL 30 ESEM) for habit determination were made. 

This paper presents results from a study of assemblies composed of glass fibre reinforced epoxy composites. First, tests performed to produce mixed mode fracture envelopes are presented. Then results from tests on lap shear and L-stiffener specimens are given. These enabled failure mechanisms to be examined in more detail using an image analysis technique to quantify local strain fields. Finally the application of a fracture-mechanics-based analysis to predict the failure loads of top-hat stiffeners with and without implanted bond-line defects is described. Correlation between test results and predictions is reasonable, but special attention is needed to account for size effects and micro-structural variations induced by the assembly process. 

The paper is presented in three parts. First, the tests employed to determine the mixed mode fracture envelope of a glass fibre reinforced epoxy composite adhesively bonded with either a brittle or a ductile adhesive are briefly described. These include mode I (DCB), and mixed mode (MMB) with various mixed mode (I/II) ratios. In the second part of the paper different structural joints will be discussed. These include single and double lap shear and L-specimens. In a recent European thematic network lap shear and double lap shear composite joints were tested, and predictions of failure load were made by different academic and industrial partners [9,10]. It was apparent that considerable differences existed between different analytical predictions and FE analyses, and correlation with tests proved complex. In particular, the progressive damage development in assemblies bonded with a ductile adhesive was not treated adequately. A more detailed study of damage mechanisms was therefore undertaken, using image analysis combined with microscopy to examine the crack tip strain fields and measure adherend displacements. This is described below and correlation is made between predicted displacements and failure loads, based on the mixed mode envelope determined previously, and measured values. 

Abstract The effects of the amount of rubber, the concentration of fibres and the state of the fibre/matrix interface upon the mechanical behaviour of short glass fibre-reinforced rubber-toughened nylon 6 ternary blends are described. First, tensile tests were carried out on different intermediate materials and then on the ternary blends to derive the stress-strain curves and document the damage mechanisms. Fracture toughness tests were implemented on compact tension specimens and the results were correlated to fractographic observations and acoustic emission analysis to assess the role of the different constituents. 

Keywords rubber-toughened thermoplastic glass fibre ternary blends mechanical tests fracture toughness J-integral image analysis fractographic observations acoustic emission. 

The potential of ultrasonic extraction for field-based extractions has been put into use in the industrial hygiene and environmental single-element analysis of, for example, lead from glass fibre filter ambient air samples [13,14] or from lead-based paint, urban dust and river sediment [15] hexavalent chromium from coal fly ash and paint chips [16] and strontium from river sediment [17]. Ultrasonic extraction has also proved effective as a prior step in multi-element determinations of heavy metals. 

A personal sampling method for common organophosphate additives in hydraulic fluids in occupational air was developed with the aim of exposure assessment in working atmospheres potentially contaminated by hydraulic fluids, simultaneously collecting both the aerosols and the vapours. The described sampler combined a glass fibre filter with a Chromosorb 106 adsorbent tube. Desorption was performed with dichloromethane for GC/MS analysis (Solbu et al. 2007). 

An alternative method for examining the dynamic mechanical properties of liquids is to coat them onto an inert support (typically a glass fibre braid). This measurement is termed Torsional Braid Analysis and does not provide quantitative modulus measurements since it is difficult to decouple the response of the substrate from that of the sample. 

---