Get attribute

You have a mapped design obtained after compile but the following command get attribute current design is.unmapped... 

The get.attribute command can be used to query the technology library for the delay model used as shown below ... 

The following table shows the driver type attribute associated with the integer output of the get attribute command... 

To check if a particular output pin of a cell in a library libA has a function attribute, use the get.attribute command as shown below ... 

The inspector also needs to accurately identify the motor carrier. This is critical so that the inspection results get attributed to the correct carrier. The inspector needs to do more than go by the company name that is on the door or on a single docmnent. Other docmnents need to be considered to verify the company name, including vehicle registration, lease agreement, or shipping papers. 

Stichlmair uses the ratio of actual velocity to this maximum velocity together with a term that increases entrainment as the distance gets small between the hquid-vapor layer and the tray deck above. His correlation spans a 10 fold range in entrainment. He shows a sharp increase in entrainment at 60 percent of the maximum velocity and attributes the increase to a shift to the spray regime. 

Except as an index of respiration, carbon dioxide is seldom considered in fermentations but plays important roles. Its participation in carbonate equilibria affects pH removal of carbon dioxide by photosynthesis can force the pH above 10 in dense, well-illuminated algal cultures. Several biochemical reactions involve carbon dioxide, so their kinetics and equilibrium concentrations are dependent on gas concentrations, and metabolic rates of associated reactions may also change. Attempts to increase oxygen transfer rates by elevating pressure to get more driving force sometimes encounter poor process performance that might oe attributed to excessive dissolved carbon dioxide. 

The key here was the theory. The pioneers familiarity with both the kinematic and the dynamic theory of diffraction and with the real structure of real crystals (the subject-matter of Lai s review cited in Section 4.2.4) enabled them to work out, by degrees, how to get good contrast for dislocations of various kinds and, later, other defects such as stacking-faults. Several other physicists who have since become well known, such as A. Kelly and J. Menter, were also involved Hirsch goes to considerable pains in his 1986 paper to attribute credit to all those who played a major part. 

As indicated above, one of the main attributes of acrylic PSAs is their broad formulation and processing latitude. While this is an important benefit to the end user, it also poses a significant challenge to the adhesive developer not only to understand what each component can do for the performance of the adhesive, but also on how to combine these components to get the best balance of properties. To help understand acrylic PSA formulation, one needs to know the major components and their impact on the PSA properties. 

These problems cannot always be attributed to the owner. An industrial client is not usually a regular developer of buildings, which are, in most cases, secondary to whatever process or production facility he wishes to construct. He is, after all, not engaged in the construction industry on a day-to-day basis. He should be entitled to expect good advice from the team he appoints, and to expect them to ask the right questions. But whatever the project, and however limited the owner s resources, it is vital that he is able to provide the necessary input to ensure that he gets what he wants. 

It is precisely the loosening of a portion of polymer to which the authors of [47] attribute the observed decrease of viscosity when small quantities of filler are added. In their opinion, the filler particles added to the polymer melt tend to form a double shell (the inner one characterized by high density and a looser outer one) around themselves. The viscosity diminishes until so much filler is added that the entire polymer gets involved in the boundary layer. On further increase of filler content, the boundary layers on the new particles will be formed on account of the already loosened regions of the polymeric matrix. Finally, the layers on all particles become dense and the viscosity rises sharply after that the particle with adsorbed polymer will exhibit the usual hydrodynamic drag. 

Most accounts of the larger A,p.,.o in carnivores have attributed this effect to higher proportion of lipids in the diet of carnivores. This arises because carnivores obtain all or most of their nutrition from the flesh of other animals, a significant part of which is composed of lipid. By contrast, lipids make up a much smaller fraction of the total carbon pool in the diet of herbivores, particularly mminants which get much of their energy from digestion of cellulose. Humans who selectively use seeds and grains as food sources obtain a... 

Why does psychotherapy - either alone or in combination with antidepressants - have more lasting effects than medication If you take antidepressants and get better, you are likely to attribute your improvement to the medication. So when you stop taking it, you might expect to get worse again. In Chapter... 

Edgar But if you allow the divisions and force the cells to differentiate in G2 instead of G1, then what would you get Perhaps these kinds of defects can be attributed to just not having enough cells to get you the right juxtaposition of cells to signal to each other to set up the fates. 

Enantioselective hydrogenation of 2,3-butanedione and 3,4-hexanedione has been studied over cinchonidine - Pt/Al203 catalyst system in the presence or absence of achiral tertiary amines (quinuclidine, DABCO) using solvents such as toluene and ethanol. Kinetic results confirmed that (i) added achiral tertiary amines increase both the reaction rate and the enantioselectivity, (ii) both substrates have a strong poisoning effect, (iii) an accurate purification of the substrates is needed to get adequate kinetic data. The observed poisoning effect is attributed to the oligomers formed from diketones. 

---