General-Type Flash

In general, one may wish to set any two specifications on flash products or conditions. For example, one may specify component concentrations in one of the products, or a product rate, plus the temperature or pressure. A flash may be operated to satisfy separation specifications, such as in multistage separation processes. The following section discusses the performance of a single equilibrium stage as a separation process for different types of systems. 

---

A lower capacity is required at critical flow for a valve with less pressure recovery. Although this may not lead to a smaller body size because of velocity and stability considerations, the choice of a more economical body type and a smaller actuator requirement is attractive. The heavy-duty angle valve finds its application generally on flashing-hydrocarbon liquid service with a coking tendency. 

The type of direct injection liners used greatly affects the quality of megabore chromatography. There are three general types of direct injection liners the straight tube, the direct flash vaporization liner, and the hot on-column. 

There are three general types of aboveground storage tanks used in the petroleum and petrochemical industries. They are selected based on the service intended and the flash points of the content. These tanks include fixed roof, external floating roof, and internal floating roof... 

Polyethers such as monensin, lasalocid, salinomycin, and narasin are sold in many countries in crystalline or highly purified forms for incorporation into feeds or sustained-release bolus devices (see Controlled-RELEASE technology). There are also mycelial or biomass products, especially in the United States. The mycelial products are generally prepared by separation of the mycelium and then drying by azeotropic evaporation, fluid-bed driers, continuous tray driers, flash driers, and other types of commercial driers (163). In countries allowing biomass products, crystalline polyethers may be added to increase the potency of the product. 

Flash thermolysis of compounds of the type (120), derivatives of Meldrum s acid , is a fairly general synthesis of ketenes (Scheme 103). Brown and coworkers (77AJC179) found that the spirooxirane (121) gave ketene, possibly via the expected carbonyloxirane (122) and probably by isomerization of carbenaoxirane (Scheme 104). 

Figure 19 illustrates one type of compression mold suitable for molding lip type shaft seals with a metal outside diameter (O.D.). Figure 19a shows the compound preform resting on the shelf and the mold beginning to close. The mold continues to close until it gets to the position shown in Fig. 19b. Finally, the mold opens as shown in Fig. 19c. It can be seen that this molding technique produces a molded lip seal with the flash already removed. In general, when using a vacuum chamber on the press, to ensure that all the air and/or gases are evacuated from the mold after closure, one or...

Pneumatic dryers, also called flash dryers, are similar in their operating principle to spray dryers. The product to be dried is dispersed into an upward-flowing stream of hot gas by a suitable feeder. The equipment acts as a pneumatic conveyor and dryer. Contact times are short, and this limits the size of particle that can be dried. Pneumatic dryers are suitable for materials that are too fine to be dried in a fluidised bed dryer but which are heat sensitive and must be dried rapidly. The thermal efficiency of this type is generally low. 

The procedure begins with a material factor that is a function only of the type of chemical or chemicals used. This factor is adjusted for general and special process hazards. These adjustments or penalties are based on conditions such as storage above the flash or boiling point, endo- or exothermic reactions, and fired heaters. Credits for various safety systems and procedures are used for estimating the consequences of the hazard, after the fire and explosion index has been determined. 

Squib. 1) (General). Any of various small size pyrotechnic or explosive devices 2) (Specific). A small explosive device similar in appearance to a detonator, but loaded with low explosive, so that its output is primarily heat (flash). Usually electrically initiated, and provided to initiate action of burning type munitions, pyrotechnic devices and rocket propellants. An electrical squib consists essentially of a tube containing a flammable material, and a small charge of powder compressed around a fine resistance wire connected to electrical leads or terminals (Ref 40a, p 135)... 

Output tests for detonator type components are generally based on an attempt to measure the brisance or the peak pressure of the shock wave. The common tests for detonators are practically all applicable to each of the three main varieties, namely stab, electric and flash detonators. Following are brief descriptions of output test for detonators and primers ... 

Whether laser flash photolysis (LFP) is used to detect RIs before they react, or matrix isolation at very low temperatures is employed to slow down or quench these reactions, spectroscopic characterization of RIs is frequently limited to infrared (IR) and/or ultraviolet-visible (UV-vis) spectroscopy. Nuclear magnetic resonance (NMR) spectroscopy, which is generally the most useful spectroscopic technique for unequivocally assigning structures to stable organic molecules, is inapplicable to many types of RI. 

---