GENERAL INDEX quality

The basic condition of the Standard application - the availability of stable coupled probabilistic or the multiple probabilistic relations between then controlled quality indexes and magnetic characteristics of steel. All the probabilistic estimates, used in the Standard, are applied at confidence level not less than 0,95. General requirements to the means of control and procedure of its performance are also stipulated. Engineers of standard development endeavoured take into consideration the existed practice of technical control performance and test at the enterprises that is why the preparation of object control for the performance of nondestructive test can be done during the process of ordinary acceptance test. It is suggested that every enterprise is operated in correspondence with direct and non-destructive tests, obtained exactly at it, for detailed process chart and definite product type, however the tests have long since been performed after development of the Standard displayed that process gives way to unification. 

Even in modern quality control laboratories you will find a number of traditional methods for the identification of single flavour compounds, for example the estimation of optical rotation, refractive index, density and melting point, since these methods are generally accepted, effective and less time-consuming. Especially for the purpose of fast identification checks of more complex systems, spectroscopic methods, above all infrared (IR) and near-IR spectroscopy, are gaining more and more importance. 

Considerable data have been published and additional unpublished confirmatory data have been collected which indicate that for a given degree of refinement, measured by increased viscosity index or decreased viscosity gravity constant, the quality of refined oils produced by all popular solvent refining processes is so nearly equivalent that there is no clear-cut generalization possible which would favor one process over another. From the point of view of economy, two other considerations are important—namely, selectivity and... 

Aromaticity is the most important property of a carbon black feedstock. It is generally measured by the Bureau of Mines Correlation Index (BMCI) and is an indication of the carbon-to-hydrogen ratio. The sulfur content is limited to reduce corrosion, loss of yield, and sulfur in the product. It may be limited in certain locations for environmental reasons. The boiling range must be low enough so that it will be completely volatilized under furnace time—temperature conditions. Alkane insolubles or asphaltenes must be kept below critical levels in order to maintain product quality. Excessive asphaltene content results in a loss of reinforcement and poor treadwear in tire applications. 

Burning-quality index an empirical numerical indication of the likely burning performance of a furnace or heater oil derived from the distillation profile (q.v.) and the API gravity (q.v.), and generally recognizing the factors of paraffinicity and volatility. 

Toraya s WPPD approach is quite similar to the Rietveld method it requires knowledge of the chemical composition of the individual phases (mass absorption coefficients of phases of the sample), and their unit cell parameters from indexing. The benefit of this method is that it does not require the structural model required by the Rietveld method. Furthermore, if the quality of the crystallographic structure is poor and contains disordered pharmaceutical or poorly refined solvent molecules, quantification by the WPPD approach will be unbiased by an inadequate structural model, in contrast to the Rietveld method. If an appropriate internal standard of known quantity is introduced to the sample, the method can be applied to determine the amorphous phase composition as well as the crystalline components.9 The Rietveld method uses structural-based parameters such as atomic coordinates and atomic site occupancies are required for the calculation of the structure factor, in addition to the parameters refined by the WPPD method of Toraya. The additional complexity of the Rietveld method affords a greater amount of information to be extracted from the data set, due to the increased number of refinable parameters. Furthermore, the method is commonly referred to as a standardless method, since the structural model serves the role of a standard crystalline phase. It is generally best to minimize the effect of preferred orientation through sample preparation. In certain instances models of its influence on the powder pattern can be used to improve the refinement.12... 

In this chapter we have reviewed a number of techniques used for optical characterization of organic samples, in particular those concerning the determination of complex optical constants and the dynamics of elementary photoexcitations. It has been stressed that very good optical quality samples are needed in order to obtain reliable estimates of the refractive index. In general, samples with controlled morphology, low defect and impurity concentration, and good optical quality allow more reliable photophysical studies and hence better determination of the intrinsic properties of the material. 

---