Free-radical polymers copolymers

The spectra of the methyl methacrylate-a-methylstyrene copolymers are similar to those of the methyl methacrylate-styrene copolymers and are not shown. The backbone methylene regions (8.1—8.6t) of the two comonomer units cannot be distinguished from each other. On the other hand, the methyl methacrylate a-methyl resonances are clearly multiple except at the two lowest values of f . In the spectrum of the 46 54 methyl methacrylate-a-methylstyrene copolymer, the shape of the methyl methacrylate a-methyl resonance is markedly altered from that observed at higher f , the peak at lower field (8.83r), which corresponds to isotactic triads in the homopolymers and is normally very small in free radical polymers, appears to be the most prominent. The a-methyl protons of the a-methylstyrene units appear at highest field, 9.6r—9.8t. Peak positions for the a-methylstyrene copolymers are... 

Effect of Substrate. Again, polyethylene and ethylene-propylene copolymers are better substrates for block formation than polypropylene (Table XI). Polyethylene is better than polypropylene, and a polyethylene-polypropylene-polyethylene type of block polymer is better than polyethylene. This agrees with what has been found for AFR polymers containing methylvinylpyridine and acrylonitrile. It also supports our belief that AFR polymers are formed by the growing of a free radical polymer onto active ends of anionic polymer chains. If it were a random grafting reaction, it would be hard to explain why a propylene polymer with a more vulnerable tertiary hydrogen should give a lower... 

While a munber of alternative polymer membranes have been developed. Nation is still considered the benchmark of proton conducting polymer membranes, and has the largest body of research hterature devoted to its study. Alternative polymer membranes are almost invariably compared to Nation . Nation is a free radical initiated copolymer consisting of crystaUiz-able, hydrophobic tetrafluoroethylene and a perfluorinated vinyl ether terminated by perfluorosulfonic acid. Nation 117 possesses an equivalent weight of 1100 (EW = mass of dry ionized polymer (g) in the protonic acid form that would neutralize one equivalent of base). Thus, there are 13 perfluoro-methylene groups (-CF2-) ( = 6.5) between pendent ionic side chains. 

The concentration of (Z)-configuration varies indirectly proportional with the polymerization temperatnre whereas the other three configurations vary directly proportional with the polymerization temperature. The total amoimt of E-, 1,2-, and 3,4- configurations vary from 5% at —40°C to 30% of the total polymer backbone at 100°C polymerization temperatures. Other structvu-al studies have involved 2,3-dichloro- butadiene homopolymer (52), the free-radical random copolymer with methyl methacrylate (53) with chloroprene, and the alternating copolymer of sulfur dioxide with chloroprene (54). Petiaud and Pham studied the thermodynamics of the various modes of imit addition (55). 

Polymeric vinylidene chloride generally produced by free radical polymerization of CH2 = CCl2. Homopolymers and copolymers are used. A thermoplastic used in moulding, coatings and fibres. The polymers have high thermal stability and low permeability to gases, and are self extinguishing. 

The elastomer produced in greatest amount is styrene-butadiene rubber (SBR) Annually just under 10 lb of SBR IS produced in the United States and al most all of it IS used in automobile tires As its name suggests SBR is prepared from styrene and 1 3 buta diene It is an example of a copolymer a polymer as sembled from two or more different monomers Free radical polymerization of a mixture of styrene and 1 3 butadiene gives SBR... 

Remember from Sec. 1.3 that graft copolymers have polymeric side chains which differ in the nature of the repeat unit from the backbone. These can be prepared by introducing a prepolymerized sample of the backbone polymer into a reactive mixture—i.e., one containing a source of free radicals—of the side-chain monomer. As an example, consider introducing polybutadiene into a reactive mixture of styrene ... 

Emulsion Adhesives. The most widely used emulsion-based adhesive is that based upon poly(vinyl acetate)—poly(vinyl alcohol) copolymers formed by free-radical polymerization in an emulsion system. Poly(vinyl alcohol) is typically formed by hydrolysis of the poly(vinyl acetate). The properties of the emulsion are derived from the polymer employed in the polymerization as weU as from the system used to emulsify the polymer in water. The emulsion is stabilized by a combination of a surfactant plus a coUoid protection system. The protective coUoids are similar to those used paint (qv) to stabilize latex. For poly(vinyl acetate), the protective coUoids are isolated from natural gums and ceUulosic resins (carboxymethylceUulose or hydroxyethjdceUulose). The hydroHzed polymer may also be used. The physical properties of the poly(vinyl acetate) polymer can be modified by changing the co-monomer used in the polymerization. Any material which is free-radically active and participates in an emulsion polymerization can be employed. Plasticizers (qv), tackifiers, viscosity modifiers, solvents (added to coalesce the emulsion particles), fillers, humectants, and other materials are often added to the adhesive to meet specifications for the intended appHcation. Because the presence of foam in the bond line could decrease performance of the adhesion joint, agents that control the amount of air entrapped in an adhesive bond must be added. Biocides are also necessary many of the materials that are used to stabilize poly(vinyl acetate) emulsions are natural products. Poly(vinyl acetate) adhesives known as "white glue" or "carpenter s glue" are available under a number of different trade names. AppHcations are found mosdy in the area of adhesion to paper and wood (see Vinyl polymers). 

Polymerization of methacrylates is also possible via what is known as group-transfer polymerization. Although only limited commercial use has been made of this technique, it does provide a route to block copolymers that is not available from ordinary free-radical polymerizations. In a prototypical group-transfer polymerization the fluoride-ion-catalyzed reaction of a methacrylate (or acrylate) in the presence of a silyl ketene acetal gives a high molecular weight polymer (45—50). 

The second type of solution polymerization concept uses mixtures of supercritical ethylene and molten PE as the medium for ethylene polymerization. Some reactors previously used for free-radical ethylene polymerization in supercritical ethylene at high pressure (see Olefin POLYMERS,LOW DENSITY polyethylene) were converted for the catalytic synthesis of LLDPE. Both stirred and tubular autoclaves operating at 30—200 MPa (4,500—30,000 psig) and 170—350°C can also be used for this purpose. Residence times in these reactors are short, from 1 to 5 minutes. Three types of catalysts are used in these processes. The first type includes pseudo-homogeneous Ziegler catalysts. In this case, all catalyst components are introduced into a reactor as hquids or solutions but form soHd catalysts when combined in the reactor. Examples of such catalysts include titanium tetrachloride as well as its mixtures with vanadium oxytrichloride and a trialkyl aluminum compound (53,54). The second type of catalysts are soHd Ziegler catalysts (55). Both of these catalysts produce compositionaHy nonuniform LLDPE resins. Exxon Chemical Company uses a third type of catalysts, metallocene catalysts, in a similar solution process to produce uniformly branched ethylene copolymers with 1-butene and 1-hexene called Exact resins (56). 

Olig omerization and Polymerization. Siace an aHyl radical is stable, linear a-olefins are not readily polymerized by free-radical processes such as those employed ia the polymerization of styrene. However, ia the presence of Ziegler-Natta catalysts, these a-olefins can be smoothly converted to copolymers of various descriptions. Addition of higher olefins during polymerization of ethylene is commonly practiced to yield finished polymers with improved physical characteristics. 

Organic peroxides are used in the polymer industry as thermal sources of free radicals. They are used primarily to initiate the polymerisation and copolymerisation of vinyl and diene monomers, eg, ethylene, vinyl chloride, styrene, acryUc acid and esters, methacrylic acid and esters, vinyl acetate, acrylonitrile, and butadiene (see Initiators). They ate also used to cute or cross-link resins, eg, unsaturated polyester—styrene blends, thermoplastics such as polyethylene, elastomers such as ethylene—propylene copolymers and terpolymers and ethylene—vinyl acetate copolymer, and mbbets such as siUcone mbbet and styrene-butadiene mbbet. 

Styrene is a colorless Hquid with an aromatic odor. Important physical properties of styrene are shown in Table 1 (1). Styrene is infinitely soluble in acetone, carbon tetrachloride, benzene, ether, / -heptane, and ethanol. Nearly all of the commercial styrene is consumed in polymerization and copolymerization processes. Common methods in plastics technology such as mass, suspension, solution, and emulsion polymerization can be used to manufacture polystyrene and styrene copolymers with different physical characteristics, but processes relating to the first two methods account for most of the styrene polymers currendy (ca 1996) being manufactured (2—8). Polymerization generally takes place by free-radical reactions initiated thermally or catalyticaHy. Polymerization occurs slowly even at ambient temperatures. It can be retarded by inhibitors. 

Eree-radical initiation of emulsion copolymers produces a random polymerisation in which the trans/cis ratio caimot be controlled. The nature of ESBR free-radical polymerisation results in the polymer being heterogeneous, with a broad molecular weight distribution and random copolymer composition. The microstmcture is not amenable to manipulation, although the temperature of the polymerisation affects the ratio of trans to cis somewhat. 

Polymers ndResins. / fZ-Butyl peroxyneopentanoate and other peroxyesters of neopentanoic acid can be used as free-radical initiators for the polymeri2ation of vinyl chloride [75-01-4] (38) or of ethylene [74-85-1]. These peresters have also been used in the preparation of ethylene—vinyl acetate copolymers [24937-78-8] (39), modified polyester granules (40), graft polymers of arninoalkyl acrylates with vinyl chloride resins (41), and copolymers of A/-vinyl-pyrrohdinone [88-12-0] and vinyl acetate [108-05-4] (42). They can also be used as curing agents for unsaturated polyesters (43). 

---