Extraction organic layer

Sample preparation 50 g Milk + 2 drops penicillinase (Difco Laboratories), let stand 1 h at 37°, add 50 mL MeCN, shake vigorously for 1 min, centrifuge at 9000 g for 10 min, decant, add 5 g NaCl, swirl to dissolve, add 100 mL dichloromethane, shake for 1 min, centrifuge at 1000 g for 10 min. Remove top aqueous layer and extract organic layer with 25 mL 10% NaCl by shaking and centrifuging as before. Combine aqueous layers, add 1 mL 0.3% mercuric chloride in water, let stand 30 min, add 1 mL 2 M HCl, extract with three 50 mL portions of dichloromethane by shaking each portion for 1 min and centri-... 

Like bromine, iodine is soluble in organic solvents, for example chloroform, which can be used to extract it from an aqueous solution. The iodine imparts a characteristic purple colour to the organic layer this is used as a test for iodine (p. 349). NB Brown solutions are formed when iodine dissolves in ether, alcohol, and acetone. In chloroform and benzene a purple solution is formed, whilst a violet solution is produced in carbon disulphide and some hydrocarbons. These colours arise due to charge transfer (p. 60) to and from the iodine and the solvent organic molecules. 

Reduction of A-nitrosomethylaniline. Into a 1 litre round-bottomed flask, fitted with a reflux condenser, place 39 g. of A-nitroso-methylaniline and 75 g. of granulated tin. Add 150 ml. of concentrated hydrochloric acid in portions of 25 ml. (compare Section IV.34) do not add the second portion until the vigorous action produced by the previous portion has subsided, etc. Heat the reaction mixture on a water bath for 45 minutes, and allow to cool. Add cautiously a solution of 135 g. of sodium hydroxide in 175 ml. of water, and steam distil (see Fig. II, 40, 1) collect about 500 ml. of distillate. Saturate the solution with salt, separate the organic layer, extract the aqueous layer with 50 ml. of ether and combine the extract with the organic layer. Dry with anhydrous potassium carbonate, remove the ether on a water bath (compare Fig. II, 13, 4), and distil the residual liquid using an air bath (Fig. II, 5, 3). Collect the pure methylaniline at 193-194° as a colourless liquid. The yield is 23 g. 

Neutralise the cold contents of the flask with 500-600 ml. of 40 per cent, aqueous sodium hydroxide solution, equip the flask for steam distillation and steam distil until about 1 litre of distillate is collected. The steam distillate separates into two layers. Add solid sodium hydroxide (< 100 g.) to complete the separation of the two layers as far as possible. Remove the upper (organic) layer and extract the aqueous layer with three 50 ml. portions of chloroform. Dry the combined organic layer and chloroform extracts with anhydrous potassium carbonate and distil the mixture through a short fractionating column (e.g., an 8 Dufton column) after a fore run of chloroform, followed by pyridine, collect the crude 4-ethylpyridine at 150-166° (49 g.). Redistil through a Fenske-... 

Introduce a solution of 100 g. of sodium bisulphite in 200 ml. of water and continue the stirring, preferably for 10 hours with exclusion of air. A thick precipitate separates after a few minutes. Collect the bisulphite compound by suction filtration, wash it with ether until colourless, and then decompose it in a flask with a lukewarm solution of 125 g. of sodium carbonate in 150 ml. of water. Separate the ketone layer, extract the aqueous layer with four 30 ml. portions of ether, dry the combined organic layers over anhydrous magnesium sulphate, remove the ether at atmospheric pressure, and distil the residual oil under reduced pressure from a Qaisen flask with fractionating side arm (Fig. II, 24, 5). Collect the cyclo-heptanone at 64r-65°/12 mm. the yield is 23 g. 

Alkvl Azides from Alkyl Bromides and Sodium Azide General procedure for the synthesis of alkyl azides. In a typical experiment, benzyl bromide (360 mg, 2.1 mmol) in petroleum ether (3 mL) and sodium azide (180 mg, 2.76 mmol) in water (3 mL) are admixed in a round-bottomed flask. To this stirred solution, pillared clay (100 mg) is added and the reaction mixture is refluxed with constant stirring at 90-100 C until all the starting material is consumed, as obsen/ed by thin layer chromatographv using pure hexane as solvent. The reaction is quenched with water and the product extracted into ether. The ether extracts are washed with water and the organic layer dried over sodium sulfate. The removal of solvent under reduced pressure affords the pure alkyl azides as confirmed by the spectral analysis. ... 

To a solution of 0.35 mol of allenyllithium in 240 ml of hexane and 200 ml of THF (see Chapter II, Exp. 13) were added 25 g of dry HMPT at -80°C. Subsequently 0.30 mol of l-bromo-3-chloropropane were added in 10 min. The reaction was very exothermic, but could be kept under control by occasional cooling in a bath with liquid nitrogen. After an additional 10 min the cooling bath was removed and the temperature was allowed to rise to -30°C. The solution was then poured into 500 ml of water. The organic layer and three ethereal extracts were dried over magnesium sulfate. The solvents were distilled off as thoroughly as possible at... 

A mixture of 0.10 mol of freshly distilled 3-methyl-3-chloro-l-butyne (see Chapter VIII-3, Exp. 5) and 170 ml of dry diethyl ether was cooled to -100°C and 0.10 mol of butyllithium in about 70 ml of hexane was added at this temperature in 10 min. Five minutes later 0.10 mol of dimethyl disulfide was introduced within 1 min with cooling betv/een -100 and -90°C. The cooling bath vjas subsequently removed and the temperature was allowed to rise. Above -25°C the clear light--brown solution became turbid and later a white precipitate was formed. When the temperature had reached lO C, the reaction mixture was hydrolyzed by addition of 200 ml of water. The organic layer and one ethereal extract were dried over potassium carbonate and subsequently concentrated in a water-pump vacuum (bath... 

A solution of methylmagnesium bromide in 150 ml of diethyl ether, prepared from 0.5 mol of methyl bromide (see Chapter II, Exp. 5) was subsequently added in 20 min with cooling at about 20°C. After the addition the mixture was warmed for 2 h under reflux (the thermometer and gas outlet were replaced with a reflux condenser), a black slurry being formed on the bottom of the flask. The mixture was cooled in a bath of dry-ice and acetone and a solution of 30 g of ammonium chlori.de in 200 ml of water was added with vigorous stirring. The organic layer and four ethereal extracts were combined, dried over potassium carbonate and subsequently concentrated in a water-pump vacuum. Careful distillation of the residue through a 40-cm... 

A stirred solution of o-methylpivalanilide (50 mmol) in dry THE (100 ml) was maintained at 15°C under a nitrogen atmosphere. A 1.5 M solution of n-butyllithium in hexane (3 equiv.) was added dropwise. The solution was then maintained at room temperature for 16h. The solution was cooled in an ice-bath and treated with 2 N HCl (60 ml). The organic layer was separated and the aqueous layer was further extracted with benzene. The combined layers were dried (MgS04). The product was obtained in 87% yield and recrystallized from ether-cyclohexane. 

Phenyl-3-oxopropanoic acid (25 mmol) and EtjN (87.5 mmol) were dissolved in THF (150 ml) and cooled to —40°C. Ethyl chloroformate (27.5 mmol) was added dropwise to this solution and then the reaction mixture was stirred for 30 min at —20°C. Di-n-hexylamine (27.5 mmol) was added to the suspension and it was stirred at room temperature for an additional hour. The reaction mixture was diluted with water (100 ml) and extracted with ether (400 ml). The extract was washed with aq. 5% HCl (100 ml) and brine (2 X 100 ml) and dried over NajSO. The crude amide was obtained by removal of the solvent in vacuo and phenylhydrazine (25 mmol) was added. The mixture was heated to 100°C for 30 min. The residue was held in vacuo to remove the water formed and then powdered ZnCl2 (125 mmol) was added. The mixture was heated at 170"C with manual stirring for 5 min. The cooled residue was dissolved in acetone (100 ml) and diluted with ether (500 ml). Water (100 ml) was added. The organic layer was separated and washed successively with 5% aq. HCl (100 ml) and brine (2 x 100 ml) and dried over NajSO. The solvent was removed in vacuo, and the residue was recrystallized from EtOAc-hexane. The yield was 79%. 

A solution of 6-bromoindole (O.lOmol) in toluene (200 ml) was treated with Pd(PPh3)4 (5mol%) and stirred for 30 min. A solution of 4-fluorophenyl-boronic acid (0.25 M, 0.15 mol) in abs. EtOH was added, followed immediately by sal aq. NaHCOj (10 eq.). The biphasic mixture was refluxed for several hours and then cooled to room temperature. The reaction mixture was poured into sat. aq. NaCl (200 ml) and the layers separated. The aq. layer was extracted with additional EtOAc (200 ml) and the combined organic layers dried (Na2S04), filtered and concentrated in vacuo. The solution was filtered through silica gel using hexane-CHjCl -hexanc for elution and evaporated. Final purification by recrystallization gave the product (19 g, 90%). 

If the volumes of the aqueous and organic layers are the same for both extractions, then the cumulative fraction of solute remaining in the aqueous layer after two extractions, (Qaq)i> is... 

An hplc assay was developed suitable for the analysis of enantiomers of ketoprofen (KT), a 2-arylpropionic acid nonsteroidal antiinflammatory dmg (NSAID), in plasma and urine (59). Following the addition of racemic fenprofen as internal standard (IS), plasma containing the KT enantiomers and IS was extracted by Hquid-Hquid extraction at an acidic pH. After evaporation of the organic layer, the dmg and IS were reconstituted in the mobile phase and injected onto the hplc column. The enantiomers were separated at ambient temperature on a commercially available 250 x 4.6 mm amylose carbamate-packed chiral column (chiral AD) with hexane—isopropyl alcohol—trifluoroacetic acid (80 19.9 0.1) as the mobile phase pumped at 1.0 mL/min. The enantiomers of KT were quantified by uv detection with the wavelength set at 254 nm. The assay allows direct quantitation of KT enantiomers in clinical studies in human plasma and urine after adrninistration of therapeutic doses. 

Deoxy-1-N-octadecylamlno-D-fructose (2). A solution of N-octadecyl-O-gluco-sylamlne 1 (2 5 g, 5 8 mmol) in pyridine (25 mL] was mixed with 0 28 N HCI (21 mL) in pyridine (5 8 mmoO- Next day, water (200 mL) was added and the product was extracted with a rnixture of 41 BOAc BuOH (200 mL) The organic layer was washed wrth water and dried (Na2S04)... 

Ethyl 4,5-Dlbenzamldopent-4-enoate (2) Ethyl 3-lmidazol-4(5)-ylpropanoale 1 (9.2 g, 54 mmol) In ElOAc (140 mL) was treated with benzoyl chloride (15 7 g, 112 mmol) In ElOAc (40 mL) and 1M NaHCOa (380 mL) added simultaneously In 1 h under Ice-cooling. The reaction mixture was stirred for 1 h, then a further portion of benzoyl chloride (IS 7 g, 112 mmol) in ElOAc) and iM NaHCOa (280 mL) was added m the same manner, followed by an additional portion o( 1M NaHCOa (200 mL) The reaction mixture was stirred for 24 h, then the organic layer was separated, concentrated, and the residue dissolved in THF (300 mL) The THF solution was stirred with 10% NaHCOa (600 mL) for 24 h to decompose any N-lormyl intermediate and to remove benzoic acxl Extraction with EtOAc, drying (Na2S04), solvent evaporation and recrystallization of the residue from EtOAc hexane afforded 16 24 g of 2 (84%), mp 128-129°C... 

S-Chloro-2-phenyllndole (2). A stirred solution ol N-(4-chioro-2-methylphenyl)-benzamkle 1 (12 25 g, 50 mmol) m THF (100 ml.) was maintained under N2 at 0°C and treated with n-txityllilhlum in hexane (0.1-0 15 mol). The stirred mature was kept at room (emperalure lor 15 h, treated with 2N HCI (60 mL) under ice cooling and extracted with PhH. The combined organic layers were concentrated to dryness to aftord 10 6 g ol 2 (94%). mp 195-196 C (trom Et20-PhH). 

---