Extraction glass

Glass Cement extract Glass Cement extract... 

Arsenic salts are sensitizers, but most often irritants. They are used in copper or gold extraction, glass, feeds, weedkillers, insecticides and ceramics. A recent case was reported in a crystal factory worker with positive patch tests to sodium arsenate, CAS registry number [7778-43-0]. 

Precipitation chromatogr. 73-23°C, column extraction glass beads... 

Cobalt compounds have been in use for centuries, notably as pigments ( cobalt blue ) in glass and porcelain (a double silicate of cobalt and potassium) the metal itself has been produced on an industrial scale only during the twentieth century. Cobalt is relatively uncommon but widely distributed it occurs biologically in vitamin B12 (a complex of cobalt(III) in which the cobalt is bonded octahedrally to nitrogen atoms and the carbon atom of a CN group). In its ores, it is usually in combination with sulphur or arsenic, and other metals, notably copper and silver, are often present. Extraction is carried out by a process essentially similar to that used for iron, but is complicate because of the need to remove arsenic and other metals. 

The sodium fusion and extraction, if performed strictly in accordance with the above directions, should be safe operations. In crowded laboratories, however, additional safety may be obtained by employing the follow ing modification. Suspend the hard-glass test-tube by the rim through a hole in a piece of stout copper sheet (Fig. 69). Place 1 -2 pellets of sodium in the tube, and heat gently until the sodium melts. Then drop the organic compound, in small quantities at a time, down — =. the tube, allowing the reaction to subside after each addition before the next is made. (If the compound is liquid, allow two or three small drops to fall at intervals from a fine dropping-tube directly on to the molten sodium.) Then heat the complete mixture as before until no further reaction occurs. 

Now grind up the mixture of solution and glass in the mortar to ensure extraction of the sodium salts, and then filter. Divide the filtrate into three portions, reserving two portions for testing for halogens and sulphur. 

Basic Component. The filtrate from (a), or the HCl extract from b), now contains the basic component in the form of its hydrochloride. Add 30% aqueous NaOH solution until alkaline to litmus. Cool, and scratch the sides of the vessel with a glass rod a white precipitate indicates a solid amine, e.g, p-toluidine or a naphthylamine. Dilute, filter off, wash well with water (recrystallise if necessary), dry and identify. 

Solids by solvents. The various forms of Soxhlet apparatus illus trated in Section 11,44 can be purchased with ground glass joints. A simplified form, in which the fragile side tubes are absent, is shown in Fig. II, 58, 1. The material to be extracted, if of granular form, may rest upon a sintered glass disc or upon a removable septum ... 

For alcohols of b.p. below 150°, mix 0- 5 g. of 3-nitrophthalic anhydride (Section VII,19) and 0-5 ml. (0-4 g.) of the dry alcohol in a test-tube fitted with a short condenser, and heat under reflux for 10 minutes after the mixture liquefies. For alcohols boiling above 150°, use the same quantities of reactants, add 5 ml. of dry toluene, heat under reflux until all the anhydride has dissolved and then for 20 minutes more remove the toluene under reduced pressure (suction with water pump). The reaction product usually solidifies upon cooling, particularly upon rubbing with a glass rod and standing. If it does not crystallise, extract it with dilute sodium bicarbonate solution, wash the extract with ether, and acidify. Recrystallise from hot water, or from 30 to 40 per cent, ethanol or from toluene. It may be noted that the m.p. of 3-nitrophthalic acid is 218°. 

Pimelic acid. Heat a mixture of 18 g. of pentamethylene dicyanide and 250 g. of 50 per cent, sulphuric acid by weight in a 750 ml. round-bottomed flask under reflux for 9 hours. INIost of the pimehc acid separates from the cold reaction mixture. Filter oflF the crystaUine acid upon a sintered glass funnel. Saturate the filtrate with ammonium sulphate and extract it with three 50 ml. portions of ether. Dissolve the residue on the filter (which is shghtly discoloured, but is fairly pure pimehc acid) in the combined ethereal extracts, dry with anhydrous sodium or magnesium sulphate, and remove the ether by distiUation. Recrystallise the residual sohd acid from benzene containing 5 per cent, of ether. The yield of pure pimehc acid, m.p, 105-106°, is 22 g. 

---