External source

Autoignition temperature. The autoignition temperature of a material is the temperature at which it will ignite spontaneously in air without any external source of ignition. 

Natural gas cap drive may be supplemented by reinjection of produced gas, with the possible addition of make-up gas from an external source. The gas injection well would be located in the crest of the structure, injecting into the existing gas cap. 

In spectroscopy it is common for transitions to be observed as absorptive lines because the Boltzmaim distribution, at equilibrium, ensures a higher population of the lower state than the upper state. Examples where emission is observed, which are by definition non-equilibrium situations, are usually cases where excess population is created in the higher level by infiising energy into the system from an external source. 

Here t. is the intrinsic lifetime of tire excitation residing on molecule (i.e. tire fluorescence lifetime one would observe for tire isolated molecule), is tire pairwise energy transfer rate and F. is tire rate of excitation of tire molecule by the external source (tire photon flux multiplied by tire absorjDtion cross section). The master equation system (C3.4.4) allows one to calculate tire complete dynamics of energy migration between all molecules in an ensemble, but tire computation can become quite complicated if tire number of molecules is large. Moreover, it is commonly tire case that tire ensemble contains molecules of two, tliree or more spectral types, and experimentally it is practically impossible to distinguish tire contributions of individual molecules from each spectral pool. 

In contrast to the point charge model, which needs atom-centered charges from an external source (because of the geometry dependence of the charge distribution they cannot be parameterized and are often pre-calculated by quantum mechanics), the relatively few different bond dipoles are parameterized. An elegant way to calculate charges is by the use of so-called bond increments (Eq. (26)), which are defined as the charge contribution of each atom j bound to atom i. 

HypcrCb cm in tegrates cq tiation s 26 an d 27 to describe tb c mot ion s of atom s. In the absence of temperature regulation, tli ere are no external sources or depositories of energy, fhat is. no other energy terms exist in the Hamiltonian, and the total energy of the system is con slant. 

ZIXDO/S is parameteri/ed to reproduce spectroscopic transitions, therefore we do not recommend using this method for geometry optim i/ation. You can obtain better results by performing a single-point calculation wuth ZIXDO/S on a geometry obtained from the Model Builder, an optim Ization iisln g one of IlyperChem s oth er methods, or an external source. 

Selectivity in FIA is often better than that for conventional methods of analysis. In many cases this is due to the kinetic nature of the measurement process, in which potential interferents may react more slowly than the analyte. Contamination from external sources also is less of a problem since reagents are stored in closed reservoirs and are pumped through a system of transport tubing that, except for waste lines, is closed to the environment. 

Direct-inlet probe. A shaft or tube having a sample holder at one end that is inserted into the vacuum system of a mass spectrometer through a vacuum lock to place the sample near to, at the entrance of, or within the ion source. The sample is vaporized by heat from the ion source, by heat applied from an external source, or by exposure to ion or atom bombardment. Direct-inlet probe, direct-introduction probe, and direct-insertion probe are synonymous terms. The use of DIP as an abbreviation for these terms is not recommended. 

Additional improvements have been incorporated since 1966 with the availabihty of thinner float glass. Glass thickness and interlayer thickness have been studied to optimize the product for occupant retention, occupant injury, and damage to the windshield from external sources (30,31). The thinner float glass windshields are more resistant to stone impacts than the early plate glass windshields. The majority of laminated windshields are made of two pieces of 2—2.5 mm aimealed glass and 0.76 mm of controlled adhesion interlayer. 

In principle, after initiation the laser should be operatable purely by chemical reaction, without any external sources of electrical power. In practice, most chemical lasers do use a sustaining source of electrical power. 

The ignition temperature or autoignition temperature is the minimum temperature of a flammable mixture that is required to initiate or cause self-sustained combustion without ignition from an external source of energy such as a spark or flame (ASTM D2155). 

P. M. Noiling, "Accessiag Technology fiom External Sources Usiag External Sources foi CEC Alternatives," Industrial Research Institute Roundtable, Washiagtoa, D.C., July 28, 1994. 

A critical but often overlooked aspect of the technical service function is the value of relationships that develop between more senior members of the technical service staff and their coUeagues at customer sites. Professional relationships provide value both to suppHer and customer by virtue of the tmst and respect generated in a successhil technical service interaction, analogous to the types of mutuaUy valuable relationships that can develop between suppHer sales personnel and a customer s purchasing personnel. A more efficient process of gathering and dispersing new and usehil technical information can result from these relationships, because the persons involved work in different environments and are exposed in the course of their work to different external sources of information. 

In general, low level detection is masked by the noise level inherent in any measuring device. Electrochemical methods are susceptible to electrical interference from external sources, variations in reference electrode parameters resulting from aging or contamination, and interference from redox... 

External Control. The use of external control to govern the release of dmgs from dehvery systems has largely been experimental. A number of mechanisms have been explored, and include external sources such as electrical currents, magnetism, ultrasound, temperature changes, and irradiation. 

Leachate in landfills. Leachate may be defined as hquid that has percolated through sohd waste and has extracted dissolved or suspended materials from it. In most landfills, the liqiiid portion of the leachate is composed of the liquid produced from the decomposition of the wastes and liquid that has entered the landfill from external sources, such as surface drainage, rainfall, groundwater, and water form underground springs. Representative data on chemical characteristics of leachate are reported in Table 25-72. 

Examples of the sacrificial-anode method include the use of zinc, magnesium, or aluminum as anodes in electrical contact with the metal to be protected. These may be anodes buried in the ground for protection of underground pipe lines or attachments to the surfaces of equipment such as condenser water boxes or on ship hulls. The current required is generated in this method by corrosion of the sacrificial-anode material. In the case of the impressed emf, the direct current is provided by external sources and is passed through the system by use of essentially nonsacrificial anodes such as carbon, noncor-rodible alloys, or platinum buried in the ground or suspended in the electrolyte in the case of aqueous systems. 

Attack always occurs beneath a deposit. Cooling water system deposits are ubiquitous. Deposits can be generated internally as precipitates, laid down as transported corrosion products, or brought into the system from external sources. Hence, underdeposit corrosion can be found in virtually any cooling water system at any location. Especially troubled... 

Iq = generator rated current in A. eos (p = generator rated p.f. which is quite high compared to a motor, as the reactive power is now supplied by the external source. 

A back-pressure (noncondensing) turbine may also be used if there is a profitable use for intermediate-pressure steam. In the unlikely event that large quantities of steam are required, additional high-pressure steam from an external source might be necessary. However, while it is theoretically possible that the amount of heat generated in the nitric acid plant will be insufficient to cover the entire demand, this is not usually a valid concern. 

---