Equivalence volume

For an actual determination, first place in J some stable liquid the boiling-point of which is at least 50 above that of the organic liquid the pour density of which is to be measured. This difference in boiling-point is important, because it is essential that the organic liquid, when nbsequently dropped into the bottom of T, should volatilise rapidly nd so push out an equivalent volume of air before the organic vapour can diffuse up the tube T and possibly condense in the cooler ttppcr portion of the tube. Suitable liquids for use in the jacket are ter, chlorobenzene (132°), rym-tetrachloro-ethane (147 ), P ... 

A single bubble rises through a fluid bed at a velocity, proportional to the square root of its diameter, or more accurately, the diameter of a sphere of equivalent volume ... 

Raw material usages per ton of carbon disulfide are approximately 310 m of methane, or equivalent volume of other hydrocarbon gas, and 0.86—0.92 ton of sulfur (87,88), which includes typical Claus sulfur recovery efficiency. Fuel usage, as natural gas, is about 180 m /ton carbon disulfide excluding the fuel gas assist for the incinerator or flare. The process is a net generator of steam the amount depends on process design considerations. 

In Figure 1, the equivalent diameter is related to regular shapes through equivalent volumes by the following formulas ... 

Developing the arguments in the same manner as the plate theory, let a volume (dv) of mobile phase, equivalent to (cadv) ml, enter the cell, and let the concentration of solute (a) in the incremental volume be (Xn). Let an equivalent volume (cadv) of mobile phase be displaced from the cell, and let the concentration of solute in the mobile phase contained by the cell prior to the introduction of the volume (dv) be... 

When it is considered that the volume of 1 km of 900 mm pipe is 636 dm, and if the pressure is allowed to fall from 42 bar to 19 bar, the equivalent volume of gas at standard conditions is 14,628 dm, then this should be compared to the capacity of a low-pressure gas holder of typically 28,320dm (1 million ft ). Two kilometers of pipeline operated under these conditions is therefore the equivalent of one gas holder. 

Charcoal absorption towers (not included in the flowsheet) were used to keep the sulfur content in the fresh feed gas less than 0.1 ppm in equivalent volume of H2S. 

V = equivalent volume of a spherically rotating molecule, R = the gas constant, and T = temperature in Kelvins. 

Transfer an aliquot of the sample extract equivalent to 2 g of matrix into a round-bottom flask (250-mL). Add an equivalent volume of ethyl acetate to the sample to... 

For milk, transfer the entire sample extract into a separatory funnel (250-mL), add an equivalent volume of dichloromethane plus a half equivalent volume of sodium chloride solution (5%, w/v). Shake the separatory funnel for 2 min and allow the phases to separate. Partially fill a glass filter funnel with anhydrous sodium sulfate (approximately 10 g) and filter the lower dichloromethane layer through the sodium sulfate, collecting the filtrate in a round-bottom flask (250-mL). Wash the sodium sulfate with dichloromethane (5 mL) and collect the washings in the same round-bottom flask. Rotary evaporate the sample to dryness under reduced pressure with a water-bath temperature of 40 °C. Dissolve the residue in 4 mL of ethyl acetate-toluene (3 1, v/v) and transfer the solution to a suitable vial ready for GPC cleanup. 

In its simplest form the competition model assumes the entire adsorbent surface is covered by a monolayer of solute and mobile phase molecules. Under normal chromatographic conditions, the concentration of sample molecules will be small and the adsorbed monolayer will consist mainly of mobile phase molecules. Retention of a solute molecule occurs by displacing a roughly equivalent volume of mobile phase molecules from the monolayer to make the surface accessible to the adsorbed solute aiolecule. For elution of the solute to occur -the above process must be reversible, and can be represented by the equilibrium depicted by equation (4.6)... 

Why is it important to have equivalent volumes in the test tubes used in Part B ... 

Equation (1) points to a number of important particle properties. Clearly the particle diameter, by any definition, plays a role in the behavior of the particle. Two other particle properties, density and shape, are of significance. The shape becomes important if particles deviate significantly from sphericity. The majority of pharmaceutical aerosol particles exhibit a high level of rotational symmetry and consequently do not deviate substantially from spherical behavior. The notable exception is that of elongated particles, fibers, or needles, which exhibit shape factors, kp, substantially greater than 1. Density will frequently deviate from unity and must be considered in comparing aerodynamic and equivalent volume diameters. 

In a typical titration with the autotitrator a significant fraction of the equivalence volume is added in a single aliquot and allowed to equilibrate before further titrant is added. The end point is detected by comparing changes in the millivolt output of the light source (Figure 1) ( ). 

TITRATIONS FOR COMPARISON OF METHODS. The automated photometric and turbidimetric methods were compared using 30 cm3 samples of surfactant solution containing a nominal 20 mol SDBS to give an equivalence volume of 5 cm3. The effect of salinity on the titrations was studied using samples prepared containing sodium chloride concentrations of 0.0, 0.14, 0.70 and 1.46 wt%. The influence of the choice of filter (580 or 620 nm) was also investigated. 

Analysis of equivalence volumes from titration curve minima. 

A glass tube fixed-bed reactor was used as a closed static reactor. The cyclotron produced nC-radioisotope (Ti/2=20.4 min) was used for nC-labeled methanol production by radiochemical process. The nC-labeled methanol (shortly nC-methanol, - 3pmol, -600 MBq) was then introduced into 250 mg of zeolite at ambient temperature by He gas flow. Afterwards, equivalent volume of liquid methyl iodide was injected into nC-methanol to have mixture of methanol and methyl iodide and introduced into catalyst for investigation of methyl iodide influence. After adsorption (2 min), the catalyst was heated up to the required temperature. 

Energy of explosion. The energy of explosion values given in Table 16.2 should be considered as the theoretical maxima, and yield factors of 10% are considered reasonable for fuel-air explosions. For equivalent volume storage, hydrogen has the least theoretical explosive potential of the three fuels considered, albeit it has the highest heat of combustion and explosive potential on a mass basis. 

---