Elastomer commercial

The 1,4-polymers of isoprene and 1,3-butadiene and some of their copolymers (Butyl, SBR, NBR) comprise the largest group of elastomers. Commercial vulcanization is achieved almost exclusively by heating with sulfur. The reaction mechanism is probably ionic and involves both sulfur addition to the double bonds in the polymer chains and substitution at the allylic hydrogen... 

An alternating copolymer of TFE and propylene (TEE/P) and a terpolymer TFE/P/VDF are fluorocarbon elastomers commercially available under the trademark APE AS. They are characterized by improved low-temperature and electrical properties and steam resistance when compared with FKM and are comparable to PPKM in chemical resistance at lower cost (details in next section). TFE/P has the ASTM D1418 and the ISO 1629 designations FEPM, and in ASTM D2000/SAE J200 it is classified as Type/Class HK. 

Styrene-butadiene rubber is the largest volume synthetic elastomer commercially available. It ean be produced by free-radical emulsion polymerization of styrene and butadiene either at 50 to 60°C (hot emulsion SBR) or at about 5°C (cold emulsion SBR). The two kinds of SBR have sigmfieantly different properties. The hot emulsion SBR process, which was developed st, leads to a more branehed polymer than the cold emulsion process. Cold SBR has a better abrasion resistance and, eonsequently, provides better tread wear and dynamic properties. 

NR, cw-l,4-polyisoprene, is an elastomer. Commercially, NR is almost exclusively obtained from Hevea brasiliensis It exists in two isomeric forms, the cis-, and trans-, because of the presence of double bond in its chains. The NR... 

Nitrile rubbers are broadly defined as copolymers of a diene and a vinyl unsaturated nitrile. This chapter will focus primarily on emulsion-polymerized copolymers of 1,3-butadiene and acrylonitrile, which represent the bulk of the commercially available nitrile elastomers. Commercial nitrile rubbers contain between 15 and 50% acrylonitrile, and have the following general structure ... 

As the demand for rubber increased so did the chemical industry s efforts to prepare a synthetic sub stitute One of the first elastomers (a synthetic poly mer that possesses elasticity) to find a commercial niche was neoprene discovered by chemists at Du Pont in 1931 Neoprene is produced by free radical polymerization of 2 chloro 1 3 butadiene and has the greatest variety of applications of any elastomer Some uses include electrical insulation conveyer belts hoses and weather balloons... 

These ethers readily copolymerize with tetrafluoroethylene and other fluoroalkenes to commercially significant plastics, elastomers, and ion-exchange resins such as Teflon PFA, Kalrez, andNafton (see Fluorine compounds organic-tethafluoroethylene-perfluorovinylETHERcopolya rs EuASTOPffiRS, SYNTHETIC-FLUOROCARBONELASTOTffiRS lONIC POLYTffiRS). 

FLUOROTRIAZINES Riag-fluoriaated triaziaes are used ia fiber-reactive dyes. Perfluoroalkyl triaziaes are offered commercially as mass spectral markers and have been iatensively evaluated for elastomer and hydraulic fluid appHcations. Physical properties of representative fluorotriaziaes are listed ia Table 13. Toxicity data are available. For cyanuric fluoride, LD g =3.1 ppm for 4 h (iahalatioa, rat) and 160 mg/kg (skin, rabbit) (127). 

Uses. Vinyhdene fluoride is used for the manufacture of PVDF and for copolymerization with many fluorinated monomers. One commercially significant use is the manufacture of high performance fluoroelastomers that include copolymers of VDF with hexafluoropropylene (HFP) (62) or chlorotrifluoroethylene (CTFE) (63) and terpolymers with HEP and tetrafluoroethylene (TEE) (64) (see Elastomers, synthetic-fluorocarbon elastomers). There is intense commercial interest in thermoplastic copolymers of VDE with HEP (65,66), CTEE (67), or TEE (68). Less common are copolymers with trifluoroethene (69), 3,3,3-trifluoro-2-trifluoromethylpropene (70), or hexafluoroacetone (71). Thermoplastic terpolymers of VDE, HEP, and TEE are also of interest as coatings and film. A thermoplastic elastomer that has an elastomeric VDE copolymer chain as backbone and a grafted PVDE side chain has been developed (72). 

Hydrocarbon resins are used extensively as modifiers in adhesives, sealants, printing inks, paints and varnishes, plastics, road marking, flooring, and oil field appHcations. In most cases, they ate compounded with elastomers, plastics, waxes, or oils. Selection of a resin for a particular appHcation is dependent on composition, molecular weight, color, and oxidative and thermal stabiHty, as weU as cost. A listing of all hydrocarbon resin suppHers and the types of resins that they produce is impractical. A representative listing of commercially available hydrocarbon resins and their suppHers is included in Table 6. 

At one time, the only commercial route to 2-chloro-1,3-butadiene (chloroprene), the monomer for neoprene, was from acetylene (see Elastomers, synthetic). In the United States, Du Pont operated two plants in which acetylene was dimeri2ed to vinylacetylene with a cuprous chloride catalyst and the vinyl-acetylene reacted with hydrogen chloride to give 2-chloro-1,3-butadiene. This process was replaced in 1970 with a butadiene-based process in which butadiene is chlorinated and dehydrochlorinated to yield the desired product (see Chlorocarbonsandchlorohydrocarbons). 

Butyl mbber, a copolymer of isobutjiene with 0.5—2.5% isoprene to make vulcanization possible, is the most important commercial polymer made by cationic polymerization (see Elastomers, synthetic-butyl rubber). The polymerization is initiated by water in conjunction with AlCl and carried out at low temperature (—90 to —100° C) to prevent chain transfer that limits the molecular weight (1). Another important commercial appHcation of cationic polymerization is the manufacture of polybutenes, low molecular weight copolymers of isobutylene and a smaller amount of other butenes (1) used in adhesives, sealants, lubricants, viscosity improvers, etc. 

Applications. Among the P—O- and P—N-substituted polymers, the fluoroalkoxy- and aryloxy-substituted polymers have so far shown the greatest commercial promise (14—16). Both poly[bis(2,2,2-trifluoroethoxy)phosphazene] [27290-40-0] and poly(diphenoxyphosphazene) [28212-48-8] are microcrystalline, thermoplastic polymers. However, when the substituent symmetry is dismpted with a randomly placed second substituent of different length, the polymers become amorphous and serve as good elastomers. Following initial development of the fluorophosphazene elastomers by the Firestone Tire and Rubber Co., both the fluoroalkoxy (EYPEL-F) and aryloxy (EYPEL-A) elastomers were manufactured by the Ethyl Corp. in the United States from the mid-1980s until 1993 (see ELASTOLffiRS,SYNTHETic-PHOSPHAZENEs). 

This simple reaction is the bedrock of the polyurethane iadustry (see Urethane polymers). Detailed descriptions of the chemistry and process have been published (65—67). Certain carbamates are known to reversibly yield the isocyanate and polyol upon heating. This fact has been commercially used to synthesize a number of blocked isocyanates for elastomer and coating appHcations. 

Oxidation Catalysis. The multiple oxidation states available in molybdenum oxide species make these exceUent catalysts in oxidation reactions. The oxidation of methanol (qv) to formaldehyde (qv) is generally carried out commercially on mixed ferric molybdate—molybdenum trioxide catalysts. The oxidation of propylene (qv) to acrolein (77) and the ammoxidation of propylene to acrylonitrile (qv) (78) are each carried out over bismuth—molybdenum oxide catalyst systems. The latter (Sohio) process produces in excess of 3.6 x 10 t/yr of acrylonitrile, which finds use in the production of fibers (qv), elastomers (qv), and water-soluble polymers. 

Noncrystalline aromatic polycarbonates (qv) and polyesters (polyarylates) and alloys of polycarbonate with other thermoplastics are considered elsewhere, as are aHphatic polyesters derived from natural or biological sources such as poly(3-hydroxybutyrate), poly(glycoHde), or poly(lactide) these, too, are separately covered (see Polymers, environmentally degradable Sutures). Thermoplastic elastomers derived from poly(ester—ether) block copolymers such as PBT/PTMEG-T [82662-36-0] and known by commercial names such as Hytrel and Riteflex are included here in the section on poly(butylene terephthalate). Specific polymers are dealt with largely in order of volume, which puts PET first by virtue of its enormous market volume in bottie resin. 

Thermoplastic copolyester elastomers are generally block copolymers produced from short-chain aUphatic diols, aromatic diacids, and polyalkjlene ether-diols. They are often called polyesterether or polyester elastomers. The most significant commercial product is the copolymer from butane-l,4-diol, dimethyl terephthalate, and polytetramethylene ether glycol [25190-06-1J, which produces a segmented block copolyesterether with the following stmcture. 

Moreover, commercially available triblock copolymers designed to be thermoplastic elastomers, not compatihilizers, are often used in Heu of the more appealing diblock materials. Since the mid-1980s, the generation of block or graft copolymers in situ during blend preparation (158,168—176), called reactive compatibilization, has emerged as an alternative approach and has received considerable commercial attention. 

Cationic Polymerization. For decades cationic polymerization has been used commercially to polymerize isobutylene and alkyl vinyl ethers, which do not respond to free-radical or anionic addition (see Elastomers, synthetic-BUTYLRUBBEr). More recently, development has led to the point where living cationic chains can be made, with many of the advantages described above for anionic polymerization (27,28). 

---