Elastic modulus elasticity

Youngscher Modul modulus of elasticity, elastic modulus, tensile modulus. 

Modulus of elasticity (elastic modulus, Young s modulus) The ratio of stress to corresponding strain below the elastic limit of a material. 

The importance of polymer composites arises largely from the fact that such low density materials can have unusually high elastic modulus and tensile strength. Polymers have extensive applications in various fields of industry and agriculture. They are used as constructional materials or protective coatings. Exploitation of polymers is of special importance for products that may be exposed to the radiation or temperature, since the use of polymers make it possible to decrease the consumption of expensive (and, sometimes, deficient) metals and alloys, and to extent the lifetime of the whole product. 

These fascinating bicontinuous or sponge phases have attracted considerable theoretical interest. Percolation theory [112] is an important component of such models as it can be used to describe conductivity and other physical properties of microemulsions. Topological analysis [113] and geometric models [114] are useful, as are thermodynamic analyses [115-118] balancing curvature elasticity and entropy. Similar elastic modulus considerations enter into models of the properties and stability of droplet phases [119-121] and phase behavior of microemulsions in general [97, 122]. 

In AFM, the relative approach of sample and tip is nonnally stopped after contact is reached. Flowever, the instrument may also be used as a nanoindenter, measuring the penetration deptli of the tip as it is pressed into the surface of the material under test. Infomiation such as the elastic modulus at a given point on the surface may be obtained in tliis way [114], altliough producing enough points to synthesize an elastic modulus image is very time consuming. 

Secondly, the ultimate properties of polymers are of continuous interest. Ultimate properties are the properties of ideal, defect free, structures. So far, for polymer crystals the ultimate elastic modulus and the ultimate tensile strength have not been calculated at an appropriate level. In particular, convergence as a function of basis set size has not been demonstrated, and most calculations have been applied to a single isolated chain rather than a three-dimensional polymer crystal. Using the Car-Parrinello method, we have been able to achieve basis set convergence for the elastic modulus of a three-dimensional infinite polyethylene crystal. These results will also be fliscussed. 

In Figure 5.24 the predicted direct stress distributions for a glass-filled epoxy resin under unconstrained conditions for both pha.ses are shown. The material parameters used in this calculation are elasticity modulus and Poisson s ratio of (3.01 GPa, 0.35) for the epoxy matrix and (76.0 GPa, 0.21) for glass spheres, respectively. According to this result the position of maximum stress concentration is almost directly above the pole of the spherical particle. Therefore for a... 

The glass-ceramic phase assemblage, ie, the types of crystals and the proportion of crystals to glass, is responsible for many of the physical and chemical properties, such as thermal and electrical characteristics, chemical durabiUty, elastic modulus, and hardness. In many cases these properties are additive for example, a phase assemblage comprising high and low expansion crystals has a bulk thermal expansion proportional to the amounts of each of these crystals. 

Nylon-6. Nylon-6—clay nanometer composites using montmorillonite clay intercalated with 12-aminolauric acid have been produced (37,38). When mixed with S-caprolactam and polymerized at 100°C for 30 min, a nylon clay—hybrid (NCH) was produced. Transmission electron microscopy (tern) and x-ray diffraction of the NCH confirm both the intercalation and molecular level of mixing between the two phases. The benefits of such materials over ordinary nylon-6 or nonmolecularly mixed, clay-reinforced nylon-6 include increased heat distortion temperature, elastic modulus, tensile strength, and dynamic elastic modulus throughout the —150 to 250°C temperature range. 

Hardness is a measure of a material s resistance to deformation. In this article hardness is taken to be the measure of a material s resistance to indentation by a tool or indenter harder than itself This seems a relatively simple concept until mathematical analysis is attempted the elastic, plastic, and elastic recovery properties of a material are involved, making the relationship quite complex. Further complications are introduced by variations in elastic modulus and frictional coefficients. 

For most hydrardic pressure-driven processes (eg, reverse osmosis), dense membranes in hoUow-fiber configuration can be employed only if the internal diameters of the fibers are kept within the order of magnitude of the fiber-wall thickness. The asymmetric hoUow fiber has to have a high elastic modulus to prevent catastrophic coUapse of the filament. The yield-stress CJy of the fiber material, operating under hydrardic pressure, can be related to the fiber coUapse pressure to yield a more reaUstic estimate of plastic coUapse ... 

Industrially, polyurethane flexible foam manufacturers combine a version of the carbamate-forming reaction and the amine—isocyanate reaction to provide both density reduction and elastic modulus increases. The overall scheme involves the reaction of one mole of water with one mole of isocyanate to produce a carbamic acid intermediate. The carbamic acid intermediate spontaneously loses carbon dioxide to yield a primary amine which reacts with a second mole of isocyanate to yield a substituted urea. 

Metal-Matrix Composites. A metal-matrix composite (MMC) is comprised of a metal ahoy, less than 50% by volume that is reinforced by one or more constituents with a significantly higher elastic modulus. Reinforcement materials include carbides, oxides, graphite, borides, intermetahics or even polymeric products. These materials can be used in the form of whiskers, continuous or discontinuous fibers, or particles. Matrices can be made from metal ahoys of Mg, Al, Ti, Cu, Ni or Fe. In addition, intermetahic compounds such as titanium and nickel aluminides, Ti Al and Ni Al, respectively, are also used as a matrix material (58,59). P/M MMC can be formed by a variety of full-density hot consolidation processes, including hot pressing, hot isostatic pressing, extmsion, or forging. 

Fig. 11. Modulus inciease as a function of fibei volume fraction alumina fiber-reinforced aluminum—lithium alloy matrix for (a) E (elastic modulus),...

Al—Li. Ahoys containing about two to three percent lithium [7439-93-2] Li, (Fig. 15) received much attention in the 1980s because of their low density and high elastic modulus. Each weight percent of lithium in aluminum ahoys decreases density by about three percent and increases elastic modulus by about six percent. The system is characteri2ed by a eutectic reaction at 8.1% Li at 579°C. The maximum soHd solubiHty is 4.7% Li. The strengthening precipitate in binary Al—Li ahoys is metastable Al Li [12359-85-2] having the cubic LI2 crystal stmcture, and the equhibrium precipitate is complex cubic... 

Nonoxide fibers, such as carbides, nitrides, and carbons, are produced by high temperature chemical processes that often result in fiber lengths shorter than those of oxide fibers. Mechanical properties such as high elastic modulus and tensile strength of these materials make them excellent as reinforcements for plastics, glass, metals, and ceramics. Because these products oxidize at high temperatures, they are primarily suited for use in vacuum or inert atmospheres, but may also be used for relatively short exposures in oxidizing atmospheres above 1000°C. 

The most important properties of refractory fibers are thermal conductivity, resistance to thermal and physical degradation at high temperatures, tensile strength, and elastic modulus. Thermal conductivity is affected by the material s bulk density, its fiber diameter, the amount of unfiberized material in the product, and the mean temperature of the insulation. Products fabricated from fine fibers with few unfiberized additions have the lowest thermal conductivities at high temperatures. A plot of thermal conductivity versus mean temperature for three oxide fibers having equal bulk densities is shown in Figure 2. 

---