Dry abrasion

Dry abrasive blast cleaning should be used on new steelwork where the main contaminant is mill scale. For heavily rusted and pitted steelwork, increased durability can be obtained by the use of wet abrasive blasting where this is practicable. The water will be more effective in removing the potentially destructive and corrosive soluble iron-corrosion products that form at the bottom of corrosion pits. 

As for dry abrasive cleaning, but with the advantage that there is reduced dust nuisance. 

Abrasion-resistant duties may involve abrasion in an aqueous phase or abrasion by dry particulate materials. The selection of the polyurethane type is most important to obtain the best results. Polyester-based polyurethanes perform best in dry abrasion due to their low hysteresis properties and excellent resistance to cut initiation and propagation. However, polyester polyurethanes are susceptible to hydrolytic degradation, and therefore polyether polyurethanes are normally used for aqueous abrasion duties. 

The Crimean shelf extends from Cape Khersones in the west to Cape Meganom in the east. It is widest off Cape Sarych (35-40 km) and narrowest off Cape Ayu Dag (5 km) [1,2]. This region is subjected to intensive wave action because it is exposed to all the southerly winds. The boundary of the underwater coastal slope is located at depths of 30-40 m. The near-shore zone is the area of alongshore sediment transport and smoothing of the bottom topography. Underwater and dried abrasive remnants are common the largest of them are confined to the capes composed of strong volcanic rocks [7,8]. 

For removal of surface contamination, rust scale, mill scale, and other bound moieties by wet or dry abrasion (including surface layers of metal itself) by wet or dry abrasion, erosion, and/or cavitation processes... 

Faust (13) has found deeper damage caused by lapping in boiling water, lapping with dry abrasive, and lapping with irregular SiC particles rather than the more spherical alundum. 

Despite the introduction of synthetic elastomers, ceramics and other abrasion resisting metals such as manganese, natural rubber holds a dominant position in this field of application and is the primary choice for abrasion resistance. Synthetic rubbers (particularly styrene-butadiene rubber which is dominant in the tyre industry sector) are used in dry abrasion application such as general purpose abrasion resistant sheets and conveyor belt covers, since the rubber can be reinforced with fine particles of carbon blacks to achieve dry abrasion resistance close to that of natural rubber. It should be noted that styrene-butadiene rubber is inferior to natural rubber in cutting and chipping resistance. 

Fig. 13.42 Grade 40 gray cast iron ASTM C 55 wear test results. Friction stir processing TiB particles into the surface resulted in a fourfold increase in ASTM C 55 dry abrasive wear resistance over that seen in samples without TiB particles. Courtesy of South Dakota School of Mines.

Chem. Descrip. Aliphatic poiyamine adduct (80%) in water Uses Curing agent for solid epoxy resin disps. or emulsified liq. resins to formulate coatings for min. substrates Features Prods, are very fast drying, abrasion resist., chem. resist., water and sait spray resist. 

A process has been developed to separate carpet waste using a cold, dry abrasive step [55]. Dry ice pellets are shot into an abrasive zone as a segment of discarded carpet on a conveyor system is stripped apart and disassembled. The dry ice pellets freeze the binder material (usually latex), lowering it to a temperature that makes the binder brittle and easy to break apart. The dry ice pellets sublimate directly into gas without any liquid residues. This process eliminates the need for a drying operation, which saves energy and avoids potential chemical pollution. 

COMPARATIVE DRY ABRASION RESISTANCE OF POLYURETHANES VERSUS OTHER COMMON RUBBERS, PLASTICS AND METALS... 

Dry abrasive blast consists of a uniform blasting of the surface with a clean, fine, nonmetaUic grit such as flintstones, silica, silicon carbide, aluminum oxide, or glass beads. The particle size will vary with the surface and the material. The degree of blasting for metal substrates should be a white metal blast —complete removal of... 

MBI Methylene Blue Index MCC Test. (Metodo Centro Ceramica) is a test for the surface abrasion resistance of glazed tiles, specified in BS 6431 Pt 20. It uses a dry abrasive, in contrast to the PEI TEST (q.v.) which is also specified. MCC - IP. Static Leach TesL Speciments of known geometric surface are immersed in selected leachants, without agitation, for defined time intervals at defined temperatures. The test has been applied to dental ceramics, with leach periods of 1,7,14 and 28 days at OO C, with leachants chosen to... 

Carbon steel flat-top chains normally are made from cold-finished carbon or low-alloy steel. Some carbon steel in flat-top chains is hardened for better abrasion resistance. Carbon steel flat-top chains are good for conveying paper, glassware, and metal parts in dry abrasive conditions. 

Teflon and lubricant-impregnated wood are sometimes used in wear strips. Teflon wear strips should only be used in low-speed and low-load applications. Lubricant-impregnated wood can be used in some dry abrasive applications. 

In the most-commonly used blasting technique — dry abrasive blasting — velocity of the blasting particles is controlled by the pressure of compressed air. It is more or less a constant for any given dry blasting equipment the mass of the abrasive particle therefore determines its impact on the steel surface. 

---