Distillation, avoiding

If necessary to interrupt the procedure, the benzene solution of 3-thenyl bromide may be stored over calcium carbonate and distilled directly from the carbonate later. The addition of a little calcium carbonate before distillation avoids the formation of a difficultly removable tarry residue. 

Purification by extraction and then distillation led to violent decomposition. Steam distillation avoided this problem. 

If an azeotropic mixture is to be separated by distillation, then use of pressure change to alter the azeotropic composition should be considered before use of an extraneous mass-separating agent. Avoiding the use of extraneous materials often can prevent environmental problems later in the design. 

Relief systems are expensive and introduce considerable environmental problems. Sometimes it is possibly to dispense with relief valves and all that comes after them by using stronger vessels, strong enough to withstand the highest pressures that can be reached. For example, if the vessel can withstand the pump delivery pressure, then a relief valve for overpressurization by the pump may not be needed. However, there may still be a need for a small relief device to guard against overpressurization in the event of a fire. It may be possible to avoid the need for a relief valve on a distillation column... 

Wastewater leaves the process from the bottom of the second column and the decanter of the azeotropic distillation column. Although both these streams are essentially pure water, they will nevertheless contain small quantities of organics and must be treated before final discharge. This treatment can be avoided altogether by recycling the wastewater to the reactor inlet to substitute part of the freshwater feed (see Fig. 10.36). 

Pure water for use in the laboratory can be obtained from tap water (hard or soft) by distillation if water of great purity is required, distillation must be carried out in special apparatus, usually made of quartz, not glass or metal precautions must be taken to avoid any spray getting into the distillate. Water which is sufficiently pure for most laboratory purposes can, however, be obtained by passing tap water through cation-exchangers and anion-exchangers as described above, when the water is deionised . 

Add 15 g, of chloroacetic acid to 300 ml. of aqueous ammonia solution d, o-88o) contained in a 750 ml. conical flask. (The manipulation of the concentrated ammonia should preferably be carried out in a fume-cupboard, and great care taken to avoid ammonia fumes.) Cork the flask loosely and set aside overnight at room temperature. Now concentrate the solution to about 30 ml. by distillation under reduced pressure. For this purpose, place the solution in a suitable distilling-flask with some fragments of unglazed porcelain, fit a capillary tube to the neck of the flask, and connect the flask through a water-condenser and receiver to a water-pump then heat the flask carefully on a water-bath. Make the concentrated solution up to 40 ml. by the addition of water, filter, and then add 250 ml. of methanol. Cool the solution in ice-water, stir well, and set aside for ca. I hour, when the precipitation of the glycine will be complete. 

Commercial diethyl carbonate may be purified by the following process. Wash 100 ml. of diethyl carbonate successively with 20 ml. of 10 per cent, sodium carbonate solution, 20 ml. of saturated calcium chloride solution, and 25 ml. of water. Allow to stand for one hour over anhydrous calcium chloride with occasional shaking, filter into a dry fiask containing 5 g. of the same desiccant, and allow to stand for a further hour. Distil and collect the fraction boiling at 125-126°. Diethyl carbonate combines with anhydrous calcium chloride slowly and prolonged contact should therefore be avoided. Anhydrous calcium sulphate may also be used. 

It is not advisable to distil the mixture almost to dryness, since, towards the end of the distillation, the inflammable butylene is formed. Butylene formation is avoided by conducting the distillation in two stages as described. 

By the controlled oxidation of primary alcohols with a solution of potassium or sodium dichromate in dilute sulphuric acid. To avoid the further oxidation to the corresponding acid, the aldehyde is removed as rapidly as possible by distillation through a fractionating column, for example ... 

Liberate the free base by adding to the phenylhydrazine hydrochloride 125 ml. of 25 per cent, sodium hydroxide solution. Extract the phenyl-hydrazine with two 40 ml. portions of benzene, dry the extracts with 25 g. of sodium hydroxide pellets or with anhydrous potassium carbonate thorough drying is essential if foaming in the subsequent distillation is to be avoided. Most of the benzene may now be distilled under atmospheric pressure, and the residual phenylhydrazine under reduced pressure. For this purpose, fit a small dropping funnel to the main neck of a 100 ml. Claisen flask (which contains a few fragments of porous porcelain) and assemble the rest of the apparatus as in Fig. II, 20, 1, but do not connect the Perkin triangle to the pump. Run in about 40 ml. of the benzene, solution into the flask, heat the latter in an air bath (Fig. II, 5, 3) so that... 

In a 500 ml. flask, fitted with a reflux condenser, place 53 g. of 1-chloro-methylnaphthalene (Section IV.23), 84 g, of hexamethylenetetramine and 250 ml. of 1 1 acetic acid [CAUTION 1-Chloromethylnaphtha-lene and, to a lesser degree, a-naphthaldehyde have lachrymatory and vesicant properties adequate precautions should therefore be taken to avoid contact with these substances.] Heat the mixture under reflux for 2 hours it becomes homogeneous after about 15 minutes and then an oil commences to separate. Add 100 ml. of concentrated hydrochloric acid and reflux for a further 15 minutes this will hydrolyse any SchifiF s bases which may be formed from amine and aldehyde present and will also convert any amines into the ether-insoluble hydrochlorides. Cool, and extract the mixture with 150 ml. of ether. Wash the ether layer with three 50 ml. portions of water, then cautiously with 50 ml. of 10 per cent, sodium carbonate solution, followed by 50 ml. of water. Dry the ethereal solution with anhydrous magnesium sulphate, remove the ether by distillation on a steam bath, and distil the residue under reduced pressure. Collect the a-naphthaldehyde at 160-162718 mm. the yield is 38 g. 

Any water present will distil with the carbon tetrachloride the hydrolysis of the chloride is thus avoided. 

---