Diffused reflectance IR Fourier transform spectroscopy DRIFTS

Diffuse Reflectance IR Fourier Transform Spectroscopy (DRIFTS) can be employed with high surface area catalytic samples that are not sufficiently transparent to be studied in transmission. In this technique, the diffusely scattered IR radiation from a sample is collected, refocussed, and analysed. Samples can be measured in the form of loose powders. 

Diffuse Reflection IR Fourier Transform Spectroscopy (DRIFT)... 

Two methods, diffuse reflectance IR Fourier transform spectroscopy (DRIFTS) and standard transmittance Fourier transform IR spectroscopy (FTIR), were compared to quantitatively determine the amoimts of silicon dioxide and phosphorous pentoxide in mixed water samples. For these studies a range of concentrations of each pure compound were prepared and IR spectra obtained on them. The spectra were analyzed in the regions of 750 to 820 cm for SiOi and 950 to 1050 cm for P2O5 chosen because their respective IR absorptions have minimal overlap in these regions. Using Beer s law plot program from the instrument, a Perkin Elmer 1000, standard curves were established for each compound and used to determine the amoimts of each compoimd in mixed samples. 

Diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) is used to obtain spectra of powders and rough polymeric surfaces such as textiles and paper. IR radiation is focused onto the surface of the sample in a cup resulting in both specular reflectance (which directly reflects off the surface having equal angles of incidence and reflectance) and diffuse reflectance (which penetrates into the sample subsequently scattering in all angles). Special mirrors allow the specular reflectance to be minimized. 

Diffuse Reflectance Infrared Fourier Transform Spectroscopy (DRIFT).6 When IR radiation is directed onto the surface of a solid sample, two types of energy reflectance can occur specular and diffuse. The specular component is the radiation that reflects directly off the sample surface (i.e., not absorbed by the sample). Diffuse reflectance is the radiation that penetrates into the sample and then emerges. Diffuse reflectance accessories are designed to optimize the diffuse reflected energy and suppress the specular component. The optics therefore selectively directs the scattered radiation to the IR detector. 

A number of experimental alternatives to traditional IR transmission spectroscopy are suitable for overcoming some of these complicating experimental factors. In the technique of diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) (Hartauer et al. 1992 Neville et al. 1992) the sample is dispersed in a matrix of powdered alkali halide, a procedure which is less likely to lead to polymorphic transformations or loss of solvent than the more aggressive grinding necessary for mull preparation or pressure required to make a pellet (Roston et al. 1993). For these reasons, Threlfall (1995) suggests that DRIFTS should be the method of choice for the initial IR examination of polymorphs. He has also discussed the possible use of attenuated total reflection (ATR) methods in the examination of polymorphs and provided a comparison and discussion of the results obtained on sulphathiazole polymorphs from spectra run on KBr disks, Nujol mulls and ATR. 

High quality IR spectra of different carbon surfaces were obtained by photo-thermal beam deflection spectroscopy (IR-PBDS) [123,124]. This technique was developed with the intention of providing an IR technique that could be used to study the surface properties of materials that are difficult or impossible to examine by conventional means. Recently, diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) has been successfully applied to study the effect of different pretreatments on the surface functional groups of carbon materials [101,125-128]. Several studies aiming to improve the characterization of the carbon electrode surface and the electrode-electrolyte interface have been carried out using various in situ IR techniques [14,128-132]. The development of in situ spec-troelectrochemical methods has made it possible to detect changes in the surface oxides in electrolyte solutions during electrochemical actions. 

For some sample types, for example a coated substrate, it is not possible to collect an infrared transmission spectrum, whereas in some cases (e.g. when there are concerns over the effects of sample preparation) it may be more desirable to collect a reflected spectrum. The most popular reflection techniques nowadays are internal reflection spectroscopy (IRS) and diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS)... 

IR spectroscopy is one of the few analytical techniques that can be used for the characterization of solid, liquid, and gas samples. The choice of sampling technique depends upon the goal of the analysis, qualitative identification or quantitative measurement of specific analytes, upon the sample size available, and upon sample composition. Water content of the sample is a major concern, since the most common IR-transparent materials are soluble in water. Samples in different phases must be treated differently. Sampling techniques are available for transmission (absorption) measurements and, since the advent of FTIR, for several types of reflectance (reflection) measurements. The common reflectance measurements are attenuated total reflectance (ATR), diffuse reflectance or diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS), and specular reflectance. The term reflection may be used in place of reflectance and may be more accurate specular reflection is actually what occurs in that measurement, for example. However, the term reflectance is widely used in the literature and will be used here. 

The primary components and the chemical structure of the raw peat and the solid product were further analyzed by Fourier transform infrared spectroscopy (FTIR) 0ASCO 670 Plus) using the Diffuse Reflectance Infrared Fourier Transform Spectroscopy (DRIFTS) technique and the JASCO IR Mentor Pro 6.5 software for spectral analysis. The cross polarization/magic angle spinning (CP/MAS) NMR spectrum of raw peat and the solid... 

Diffuse reflectance infrared Fourier transform spectroscopy (DRIFT) has become a frequently used technique to obtain IR spectra from materials intractable by transmission spectroscopy. A number of high-performance reflection accessories are available from different manufacturers (see below), allowing... 

Although acetone was a major product, it was not observed by infrared spectroscopy. Flowing helium/acetone over the catalyst at room temperature gave a prominent carbonyl band at 1723 cm 1 (not show here). In this study, a DRIFTS (diffuse reflectance infrared Fourier transform spectroscopy) cell was placed in front of a fixed reactor DRIFTS only monitored the adsorbed and gaseous species in the front end of the catalyst bed. The absence of acetone s carbonyl IR band in Figure 3 and its presence in the reactor effluent suggest the following possibilities (i) acetone formation from partial oxidation is slower than epoxidation to form PO and/or (ii) acetone is produced from a secondary reaction of PO. 

Diffuse Reflectance IR Fourier Transform (DRIFT) Spectroscopy of Air Oxidation... 

In the MIR, diffuse reflectance is very weak and could only be measured after routine FT-IR spectrometers became available (DRIFT spectroscopy, diffuse reflectance infrared Fourier-transform spectroscopy). Due to the lack of ideal non-absorbing scattering substrates in the MIR, the diffusely reflected MIR radiation is generally collected by large ellipsoidal mirrors, which cover as much area above the sample as possible. Two optical configurations are commercially available, on-axis and off-axis designs (Fig. 5.9). 

---