Detectors element

Therefore it is reasonable to prepare already the data acquisition for a three dimensional evaluation in cone-beam-technique by means of two-dimensional detectors. The system is already prepared to integrate a second detector- system for this purpose. An array of up to four flat panel detectors is foreseen. The detector- elements are based on amorphous silicon. Because of the high photon energy and the high dose rates special attention was necessary to protect the read-out electronics. Details of the detector arrangement and the software for reconstruction, visualisation and comparison between the CT results and CAD data are part of a separate paper during this conference [2]. 

There is potential confusion in the use of the word array in mass spectrometry. Historically, array has been used to describe an assemblage of small single-point ion detectors (elements), each of which acts as a separate ion current generator. Thus, arrival of ions in one of the array elements generates an ion current specifically from that element. An ion of any given m/z value is collected by one of the elements of the array. An ion of different m/z value is collected by another element. Ions of different m/z value are dispersed in space over the face of the array, and the ions are detected by m/z value at different elements (Figure 30.4). 

The NEP may be written in terms of the detector element active area, the number of detector pixels elements cormected for additive output the electronic noise bandwidth B and the detector element detectivity, D. Typically = 1, but may be increased for improved sensitivity with an attendant loss in resolution. 

Ap = the detector element (pixel) active area, typically 1.5 E-5 cm ... 

There are important figures of merit (5) that describe the performance of a photodetector. These are responsivity, noise, noise equivalent power, detectivity, and response time (2,6). However, there are several related parameters of measurement, eg, temperature of operation, bias power, spectral response, background photon flux, noise spectra, impedance, and linearity. Operational concerns include detector-element size, uniformity of response, array density, reflabiUty, cooling time, radiation tolerance, vibration and shock resistance, shelf life, availabiUty of arrays, and cost. 

Detector elements are prepared either by sublimation in the presence of a small partial pressure of O2 or by chemical deposition from alkaline solution containing a lead salt and thiourea or selenourea (63). Lead sulfide and lead selenide deposit from solutions as mirror-like coatings made up of cubic crystallites 0.2—1 p.m on a side. The reaction may nominally be represented by the following ... 

Several practical issues of the scatterometer must be considered in the case of characterizing nominally smooth surfaces. The incident laser beam may be collimated, but more commonly it is brought to a focus at a distance defined by the arc in which the detector rotates. In addition, a deflection mirror or an optical fiber might be used to direct light to the detector element. These features permit measurements close to the specular and transmitted beams, and this is critical to folly characterize the scattered light. This is especially significant since the scattered light intensity... 

The use of a linear detector array in the image plane of a polychromator in place of the fluorescence monochromator in Figure 12.1 enables the parallel data accumulation of complete fluorescence spectra. Silicon photodiode arrays, operated in a CCD mode(34) are the most widely used detector elements. The spectral response of the diodes enables fluorescence to be detected from the near-UV up to ca. 1100 nm with a peak response in the near-IR. Up to 8192 elements are now available commercially in a single linear array at low cost. However, the small length of each element (ca. 10 [im) presently limits sensitivity and hence cylindrical lens demagnification is often necessary. 

Detectors are used to convert X-ray flux into an electrical signal, which can then be digitized and stored. For imaging cabinet X-ray systems, the detectors usually consist of a folded linear array of scintillators optically coupled to photodiodes. Typically, 500-1000 such detector elements are present for single-energy imaging... 

Because the response time of the detector depends on the thermal time constant of the detector element / electrode assembly, coupled with the electrical time constant of the device capacitance and load resistor - the response versus modulation frequency (f shows a typical l//m form. 

The difference between a photoconductive detector and a photodiode detector lies in the presence of a thin p-doped layer at the surface of the detector element, above the bulk n-type semiconductor. Holes accumulate in the p-layer, and electrons in the n-type bulk, so between the two there is a region with a reduced number density of carriers, known as the depletion layer. The important effect of this is that electron-hole pairs, generated by photon absorption within this depletion layer, are subjected to an internal electric field (without the application of an external bias voltage) and are automatically swept to the p and n regions, and... 

---